Flame

Notes: The Airlectron Sensor Recorder module is equipped with a sunlight independent distance sensor to generate CV output voltages.

A distance sensor reacts to hand movements and varies the CV output voltages (bipolar/max +/- 5 V, unipolar/max 0-+10 V). The range control adjusts the detection distance (2-50 cm). The freeze function keeps the voltage when there is no continuous movement.

The recorder/looper can be used to record motion sequences for up to two minutes. This recorded data can be played back in a loop or once and restarted at the START/RESET input. LEDs indicate the status of the gate inputs and outputs.

Features:

3x controller
1x Vishay distance sensor
3x gate/trigger in- and outputs
2x CV outputs unipolar/bipolar
Power supply via Doepfer connector

8 HP

Notes: Automix is a compact three-channel mixer for audio signals and control voltages. The highlight of this module is the recording function, which makes it possible to automate level changes.

The "AUTOMIX" module is a compact three-channel mixer for audio or CV sources in the voltage range of +-5v (audio modular level).
The mix level of each track can be adjusted and recorded using the track's control. The recording time per track is over a minute. The playback speed is also adjustable.
The recorded track is played once with a short press of the play button (one shot) or with a slightly longer press in the loop.
In addition, the 3 inputs can be switched separately to +6db audio via a slide switch on the back (for external line level sources).
All three tracks have a common reset input. The track data is stored permanently (battery-backed memory).

Overview:

Signal/audio mixer with 3 channels on a sum output

- 3 tracks with 1 mix control each
- Record time (per track) max. 102 sec
- 3 signal/audio inputs (audio or CV) (-5v.. +5v)
- Inputs switchable to audio with line level (separately for each input)
- Resolution 12bit
- Sampling rate approx. 250Hz
- Modes:
- Play back one shot
- play back loop
- Switch between play back and potentiomix manually
- Adjustable playback speed
- Track data permanently stored (battery buffered)
- Common reset input for all 3 tracks

Dimensions
6 HP
38 mm deep

Current Draw
40 mA +12V
30 mA -12V

Notes: The FLAME "C-3 MK2" is a three-channel module for recording and playing back movements of controllers.

Those can be recorded with each channel's individual knob. The movements will be output as control voltages.

The recording time per track is over one minute. The playback speed is adjustable.

All three tracks have a common reset input. The track data remains permanently stored (battery-backed memory).

The module can be globally switched to bipolar or unipolar voltage range (switch on the PCB).

Inputs and outputs:

3 CV outputs bipolar +/-5v or unipolar 0-10v
additional CV input on track 1: bipolar +/-5v or unipolar 0-10v
common reset input for all three tracks
http://flame.fortschritt-musik.de/flame2/instruments_modular.html#automix

Power consumption: 30mA at +12 V and 5mA at -12 V
Depth: 33mm
6 HP

Notes: The FLAME "C-3 MK2" is a three-channel module for recording and playing back movements of controllers. These can be recorded with each channel's individual knob. The movements will be output as control voltages. The recording time per track is over one minute. The playback speed is adjustable. All three tracks have a common reset input. The track data remains permanently stored (battery-backed memory). The module can be globally switched to bipolar or unipolar voltage range (switch on the PCB).

Notes: Crossmix is a dual crossfader with the ability to record or automate crossfades.

The "CROSSMIX" module includes two independent crossfaders with two inputs on one output and is designed for audio or CV sources in the voltage range of +-5v (audio modular level).
In addition, the 4 inputs can be switched separately to +6db audio via a slide switch on the back (for external line level sources).

The two crossmix controls can be recorded. The recording time per channel is over one minute. The playback speed can be adjusted in the playback.
The recorded track is played once with a short press of the play button (one shot) or with a slightly longer press in the loop.

Both crossfaders have a separate reset input as well as a separate CV input ( +-5V ) for the control of the mix e.g. by an LFO.
The track data is stored permanently (battery-backed memory).

Overview:

Dual signal/audio crossmixer with 2 inputs each on a sum output

- 2 channels each with 1 mix control
- Record time (per channel) max. 102 sec
- per channel 2 signal/audio inputs (audio or CV) (-5v.. +5v)
- all inputs on the back can be switched separately to audio with line level
- mix also CV controllable
- each channel has separate reset input
- resolution 12bit
- sampling rate approx. 250Hz
- modes:
- play back one shot
- play back loop
- switching between play back and potimix manually
- adjustable playback speed
- Track data permanently stored (battery buffered)

Dimensions
6 HP
38 mm deep

Current Draw
40 mA +12V
30 mA -12V

Notes: The Flame DUALKEY module is a small pingable trigger envelope module, designed for small mobile euro racks.

There are two channels with following functions:

SHAPE: voltage controllable AR-envelope (release phase channel 1=logarithmic 2=linear)
TIME: voltage controllable time of the AR envelope
LEVEL: set the output voltage of the AR envelope
END-OUT: trigger output of the end of the envelope circle (like a trigger delay)
KEY-OUT: trigger/gate output of the key
KEY-IN: trigger input for pingable envelope

There are three play modes:

SHOT: one shot of the envelope
GATE: hold on the envelope after the release phase
LOOP: the envelope play in loop (like a LFO) while hold down the key

Current consumption: ca. + 40mA / - 5mA
Size: Euro rack format 3U / 10HP 50.5 x 128.5mm

Notes: Small compact joystick module with recording function.

The module can record the joystick movement to a length of about one minute. The sequence remains stored in the battery-backed RAM after switching off. When playing back the sequence, the playback speed can be manipulated.

There is a FREEZE function to hold the current joystick position. Also there are an external reset input. In addition, when moving outside the center position, a GATE is set and an additional positive CV voltage (summation of X and Y) is output in dependence. A GATE / START input is used for resetting or recording in sync.

The ranges of the X / Y output voltages are bipolar adjustable from approx. +/- 5v or unipolar from approx. 0 to + 10v. Both channels X and Y have a passive attenuator potentiometer, so that the voltage range can also be set lower.

Connections:

CV-Out-X: CV output X-axis bipolar or unipolar
CV-Out-Y: CV output Y-axis bipolar or unipolar
CV-OUT MOVE: CV output joystick movement 0..+5v
Trigger-In: Trigger input Reset/Start
Trigger-out: Trigger output Reset/Start signal ca. 10ms lenght
Gate-ACTIVITY: Gate output joystick movement

Power consumption: 30mA at +12 V and 5mA at -12 V

Depth: 40mm

8 HP

Notes: The FLAME "PANMIX" module contains two independent panning mixers with one input each on two outputs left/right and is designed for audio or CV sources in the voltage range +-5v (audio modular level). In addition, the 2 inputs can be switched separately to +6db audio (for external audio line level sources) using the slide switch on the rear panel.

The movements of the two mix controls can be recorded. The recording time per channel is more than one minute. The playback speed can be adjusted in playback. The recorded track is played back once when the Play button is pressed briefly (one shot) or in the loop when the button is pressed a little longer.

Both panning channels have a separate reset input as well as a separate CV input (+-5V ) for controlling the mix e.g. by an LFO. The track data remains permanently stored (battery buffered memory).

In addition, there are three further audio/CV signal inputs (a mono and stereo left+right), which are routed directly to the output and mixed together with the two PAN channels. This allows you to mix in other sources directly and e.g. connect two or more "PANMIX" modules together.

Dimensions
6 HP
38 mm deep

Current Draw
40 mA +12V
30 mA -12V

Notes: The QSlider black is an analogue CV source with four 60 mm faders.

The control range of the four sliders can be defined with two min/max controls.

The Min controller determines the output voltage at zero position of the slider and the Max controller determines the output voltage at the end position of the slider.

The slider now regulates between these two voltages. This allows you to restrict the control range and still have the entire control path of the slider available.

The reverse voltage is available at a second output socket (min and max are reversed). This means that the slider can also be used as a crossmix fader.

Two common channels can be operated unipolar or bipolar. The voltage ranges are 0..+10V or +/- 5V.

The output sockets are located on an extra 4HP panel for mounting at any point (with approx. 40cm long connection cable). This means that several modules can also be mounted seamlessly next to each other.

Power consumption: 30mA at +12V and 20mA at -12V and 12mA at +5V

Depth: 28mm

18 HP

Notes: The QSlider is an analog CV source with four 60 mm faders.

The control range of the four sliders can be set with two min/max controls.
The Min control sets the output voltage at zero position of the slider and the Max control sets the output voltage at the end position of the slider. The slider now controls between these two voltages. This allows you to limit the control range and still have the full control range of the slider available.
At a second output socket the inverted voltage is available (Min and Max are reversed). So the slider can also be used as a crossmix fader.

Two common channels can be operated uni- or bipolar. The voltage ranges are 0..+10V or +/- 5V.

The output sockets are located on an extra 4HP panel for mounting at any place (with approx. 40cm long connection cable). This way several modules can be mounted seamlessly next to each other.

18 HP

Notes: ***B-STOCK: Box opened, product in perfect working order***


The QSlider is an analog CV source with four 60 mm faders.

The control range of the four sliders can be set with two min/max controls.

The Min control sets the output voltage at zero position of the slider and the Max control sets the output voltage at the end position of the slider. The slider now controls between these two voltages. This allows you to limit the control range and still have the full control range of the slider available.

At a second output socket the inverted voltage is available (Min and Max are reversed). So the slider can also be used as a crossmix fader.

Two common channels can be operated uni- or bipolar. The voltage ranges are 0..+10V or +/- 5V.

The output sockets are located on an extra 4HP panel for mounting at any place (with approx. 40cm long connection cable). This way several modules can be mounted seamlessly next to each other.

HP : 18

Notes: The "uMCLK Divider" module can either work as a MIDI clock divider or as an analog clock divider. The divider outputs are assigned differently in both operating modes.

After receiving a MIDI start command, the module works as a MIDI clock divider. There are fixed dividers on 11 outputs. Via the divider output KEYS, triggers can be triggered and mixed via MIDI notes. The keyboard zone extends over three octaves. With the help of the LEARN key, the receive MIDI channel and the lowest note of this 3-octave range can be defined.

When stopped (i.e. after receiving a MIDI stop command or after switching on), the module works as an analog clock divider and divides the analog clock present at the CLOCK input. The 12 analog divider outputs can be reprogrammed via SYSEX. Ready-made SYSEX files are already available (e.g. for even / odd dividers, Fibonacci series, offbeats, etc.). The RESET input resets the analog counters or serves to deactivate the analog divider.

Connections:
- Ribbon cable adapter for Doepfer bus +/-12Volt
- Inputs: 2x Clock/Gate,Reset (0/+5..10V), 1/8th inch mono jacks
- 1x MIDI (TRS-B standard) 1/8th inch stereo jack Outputs: 1x MIDI (TRS-B standard) 1/8th inch stereo jack
- 14x Clock/Gate Divider, 1/8th inch mono jacks

Control elements:
- 1 push button with LED (LEARN key) 16 LED's
- Current consumption: max. +70..80mA / - 0 mA
- Size: Euro rack format 3U / 6HP 30x128,5x40 mm

Dimensions
5 HP
40 mm deep

Current Draw
80 mA +12V

Notes: The Flame uMGT converts 12 Midi notes (one octave) to gates or velocity outputs.

Features:

1 octave MIDI keyboard to 12 gate or velocity outputs
global Velocity CV output
global GATE output
programmable via Learn function or SYSEX
MIDI input and THRU (TRS MIDI B standard)

Power consumption: 60mA at +12 V and 30mA at -12 V

Depth: 40mm

5 HP

Notes: The FLAME uMGT converts 12 Midi notes (one octave) to gates or velocity outputs.

Notes: The Flame uMLFO consists of 14 MIDI LFOs which are synchronized to the clock. The module also works with analog clock.
Additional analog clock and reset inputs allow to create pingable LFOs.
It is possible to adjust the frequency, waveform and phase of each LFO. 12 presets are selectable via MIDI keyboard. Thanks to Sysex it is possible to program new setups.

Features:

14 MIDI LFOs (synced to MIDI clock)
also works with analog clock
additional analog clock and reset inputs (pingable LFOs)
LFO outputs programmable (rate, waveform, phase)
12 presets selectable via MIDI keyboard and LEARN function
Setups programmable also via SYSEX
LFO output voltage between -/+5V
MIDI input and THRU (TRS MIDI B standard)

5 HP

Notes: The "uMM" combines a MIDI merger and two independent THRU distributors in a module that is only 4 HP wide. All sockets on the module are in MIDI TRS-B format.

At the heart of the two-input MIDI merger is a small, powerful ARM processor with plenty of buffer memory. Two MIDI streams are mixed to one output and can also be tapped via an additional second output. Two LEDs signal the operation of the merger: one LED indicates MIDI activity at the inputs, and a second LED warns of too much data at the inputs.

The second group of functions consists of two independent, separate MIDI THRU distributors. The MIDI data at the respective MIDI input can be picked up and distributed at the three THRU outputs. If required, a 1-to-5 distributor can be created from the two units by connecting an output of the left group to the input of the right group.

Features:

4x MIDI IN (TRS-B)
2x MIDI-OUT (TRS-B)
6x MIDI-THRU (TRS-B)
Powered via Doepfer connector

4 HP

Notes: The Flame uQMCV 4Voice provides 1V/oct, gate and velocity CV signals for four voices from the incoming Midi signals and additionally offers an aftertouch and modulation CV output as well as a run transport output and clock output.

Features:

4 Midi to CV channels with Gate,Note, Velocity
5 modes are possible:
A) 4-way polyphonic (all same MIDI channel)
B) 3x polyphonic+1x monophonic (2 different MIDI channels)
C) 2x two voices (2 different MIDI channels)
D) 1x two voices and 2x monophonic (3 different MIDI channels)
E) 4x monophonic (all different MIDI channels)
2 gate outputs for MIDI-Clock Run and 1/16th clock
2 additional controller CV outputs for modulation wheel and pitchbend
MIDI Input and THRU (TRS MIDI B standard)

Power consumption: 70mA at +12 V and 20mA at -12 V

Depth: 40mm

5 HP

Notes: The FLAME "XPANMIX" module is a combination of an XFADER (Crossmixer) recorder and a PANNING Mixer recorder.

The upper part of the module contains the XFADER with two inputs to one output.
In the lower part of the module is the panning mixer with one input to two outputs left/right.
The inputs are designed for audio or CV sources with a voltage range of +-5v (Audio Modular Level).
In addition, the inputs can be switched separately to +6db audio (for external audio line level sources) using the slide switch on the rear panel.

The movements of the two mix controls can be recorded. The recording time per channel is over two minutes. The playback speed is adjustable in playback.
The recorded track is played back once when the Play button is pressed briefly (one shot) or in the loop when the button is pressed a little longer.

Both mixers have a separate reset input as well as a separate CV input ( +-5V ) for controlling the mix e.g. by an LFO.
The track data remains permanently stored (battery buffered memory).

In addition, the output of the XFader is routed to the input of the Panning Mixer if there is no cable in the PAN input.
Both mixers are thus connected in sequence and can additionally mix the XFADER in the stereo image.


Overview:

XFADER and PANNING channels with 1 mix control each
Record time (per channel) approx. 2 min
3 Signal/Audio Inputs (Audio or CV) (-5v..+5v)
all inputs separately switchable to audio with line level at rear
Mix can also be controlled via CV
each channel has separate reset input
XFADER output normalized to panning input
Resolution 12bit
Sampling rate ca.250Hz
Modes:
- Play back one shot (once running)
- play back loop (repeating)
- Switching possibility between play back and Potimix manually
- adjustable playback speed
Track data remain permanently stored (battery buffered)

Power consumption: 40mA at +12 V and 30mA at -12 V

6 HP