Back catalogue: Studio Equipment

Notes: You can now update your Bitbox mk1 or mk2 with a black faceplate. Now you can have an all black rack and have digital sampling capabilities. This is just the faceplate.

Give your module a facelift

These replacement faceplates are designed for use with the module in the traditional orientation with the screen on top. These are the same faceplates used when manufacturing our modules, but now in black. They are anodized aluminium with a bead blasted finish.

Swapping out a faceplate is easy to do, and requires a small wrench or pliers. Here are the steps to replace a faceplate:

Remove the module from the rack.
Use a small wrench or pliers to remove the small round nuts around each of the mini jacks. Note that these nuts have a notch on the top side of them. This notch fits into a specialized tool that can be used to remove these nuts more easily.
Gently tug on the four knobs to pull them off.
Use a small wrench or pliers to remove the hex nuts from the knob stems.
Remove the washers from the knob stems.
Gently pull up on the faceplate and it will slide off easily.
Place the new faceplate on the module.
Replace the washers on the knob stems.
Use a small wrench or pliers to replace the hex nuts on the knob stems.
Use a small wrench or pliers to replace the small round nuts around each of the mini jacks. Note that the notch should be on the top side of the nuts, the side away from the faceplate.
Look at the underside of the knobs and the post that they rest on. You will see that the knobs are keyed. Line up the flat edge of the hole in the knob with the flat edge of the post, and then push the knob onto the post. If you have the knob aligned properly, it should go on with moderate pressure. If it seems to require more force, please check the alignment.

Weight: 0.19 lbs
Dimensions: 5.5 × 5 × 0.25 in
Touchscreen product: bitbox, fxbox, synthbox, toolbox

Notes: Innovative little sampler groovebox. Works as a standalone unit or as a sequencer for other gear. A nice left-field alternative to the usual MPCs and Electribes.

Supplier's notes:
Blackbox is a portable sampler and groovebox that lets you record, save/load, apply effects and edit one-shot samples and beat-sliced loops. Create sequences with samples by tapping on pads, playing a virtual keyboard, using external MIDI controllers or by drawing-in notes using a standard Piano Roll editor on a fast touchscreen interface. Sequences can be played back to create song sections and entire compositions. Finish your song by mixing it, adding stereo effects and by saving it as a Preset for fast and easy recall.

Perform songs live and trigger samples on the fly. Blackbox makes it easy to create and perform music anywhere thanks to its compact and rock-solid hardware design. Just throw it in a backpack and hit the club.

Record hours of song ideas, jam sessions, and performances thanks to a microSD slot that enables you to expand internal memory.

Blackbox comes with gigabytes of premium samples and loops by SoundTrack Loops and Loopmasters to let you start making beats right out of the box.

Blackbox - your own personal sampler.

What Is Included:

- Blackbox compact sampling studio
- MicroSD card with blackbox firmware, about 60 presets and approximately 900 WAV files
- USB power cable and USB wall wart with 3 international adapters
- 2 MIDI Adapters - Male 3.5mm TRS to Female 5 pin DIN, MIDI Class B standard
- Quick Start guide to get you playing right away

Notes: A digital mixer at heart but so much more. 1010's unique take on mixing and recording includes built-in effects and EQ, compression, headphone/monitor mixes and output routing. Clever stuff.

Supplier's Notes:
Bluebox is the portable digital audio mixer that lets you get the most out of your electronic music gear. Connect your eurorack, sampler, drum machine and synthesizer outputs to 6 stereo, 3.5 mm TRS inputs and map them to 12 mono tracks or 6 stereo tracks, all with independent control for recording and playback. It's that keyboard mixer with live performance features that you always hoped someone would make.

Connect the output of your electronic music gear to Bluebox, and then route each track independently to the three outputs and effects sends. Each track offers control of volume, gain, 4 band parametric EQ, pan, mute and solo functions. Apply high-quality global reverb and delay effects along with 4 band EQ per track to add new depth to your sound with total control to quickly tweak incoming audio or track playback as needed.

With Bluebox you can record independent tracks or the Main mix using a standard microSD card. Capture your jam session for later review, or record the ultimate mix of the tracks for your song.

Bluebox's compact 5.5h x 5h x 2h case lets you tuck it into a crowded tabletop studio or throw it in your pack for the next gig.

Interact with the dynamic visual interface on the 3.5h touchscreen along with physical knobs, navigation buttons and transport buttons to quickly access the most important functions. MIDI input and output allow you to sync the clock with external gear for synchronized effects and metronome.

Add Some Colour to Your Mix:
Mix 12 mono/6 stereo tracks of live or prerecorded sound.
Independently route each track to any combination of three stereo TRS outputs:

Stereo Output 1 - Main mix
Stereo Output 2 - Assignable, with dedicated sub-mixer (pre or post fader)
Stereo Output 3 - Headphone output, with dedicated sub-mixer (pre or post fader)
Control one parameter for multiple tracks at once in Mixer mode.
Focus on one track at a time in Track mode.
Adjust the level or mute state of each output independently.
Use touch gestures or knobs to tweak your sound with four band EQ per track with support for Low Cut/Low Shelf, Parametric, and High Shelf/High Cut settings for each band.
Apply high-quality Reverb and Delay effects with independent effects sends for each track.
Override the headphone output with the Main mix on demand.
Maximize the loudness and unify your mix with the built-in global compressor
Sync to external clocks through the MIDI Input and Output.
Record hours of music as 48k, 24 bit WAVs directly to the microSD card as multi-track or as the main stereo mix.
Playback a previously recorded track while recording new ones.
Load firmware updates through the microSD card.
Mix electronic music gear such as the 1010music blackbox, eurorack modules, drum machines, samplers and synthesizers.
Save and recall Project settings including all parameters for tracks, outputs, EQ and effects.
Copyright 1010music LLC 2020 --- CONFIDENTIAL ---
Copyright 1010music LLC 2020 --- CONFIDENTIAL UNTIL 10/10/2020 ---
Fit it into a small spot on your desk and then tuck it in your pack for the next gig.

What is Included:
Bluebox digital recording mixer
A microSD card with bluebox firmware and pre-loaded project files
A USB power cable and AC adapter with 3 international adapters
2 MIDI Adapters . Male 3.5 mm TRS to Female 5 pin DIN, MIDI Class B standard
A Quick Start guide to show you the basics (full user manual available online)

Specs:
6 stereo 3.5 mm TRS inputs
12 mono tracks, 6 stereo tracks or something in between
3 independently controlled stereo 3.5 mm TRS outputs
3.5h touch screen, 4 knobs, 8 navigation buttons and 3 transport buttons
3 effects: reverb, delay and compressor
Records and plays back 48k, 24-bit audio WAV files
4 band EQ per track
MIDI In and Out for beat syncing effects
Dimensions: 5.5 x 5 x 2 (14 cm x 13 cm x 5 cm), 1 lb (450 grams)
Durable aluminum case

Notes: A 4 ft Type B MIDI Adapter

This cable enables you to connect MIDI devices that use standard MIDI cables to the stereo minijacks that use the Type B standard. The adapter cable has a male stereo minijack at one end, and a male 5 pin DIN MIDI connector on the other, and is 1.42 meters/4' 8" long. It is also useful as a converter for connecting to other MIDI devices that use a different mapping of MIDI signals to the stereo minijacks.

Early 1010music music products use the Type B mapping of MIDI signals to stereo minijacks. Bitbox mk2 and bitbox micro can use mini TRS Type A or Type B for MIDI inputs. Bitbox micro uses Type B for MIDI outputs.

The diagram to the right shows the numbering of the pins on a MIDI connector and the labels of the connection components of a stereo minijack. Type B products are compatible with cables that use the following mapping of MIDI signals between female MIDI connectors and stereo minijacks.

Notes: One of 1010music's first miniature Nanobox instruments, the Lemondrop is a granular synth in a compact format. Touchscreen interface gives full hands-on control of the four-voice sound engine.

Supplier's Notes:
Freshly Squeezed Granular Synthesis

Explore a freshly squeezed approach to granular synthesis with Nanobox | Lemondrop, a polyphonic granular mini synthesizer with intuitive touchscreen control. Four voice polyphony, two granulators and an oscillator provide a wide sonic paletteifrom lush environmental pads to rugged and glitched-out textures. Instantly morph and shape sounds with the swipe of a finger using touchscreen X/Y control. Choose from hundreds of professionally designed presets and wav files, or quickly create your own patches with deep parameter control via the 2" touchscreen. Integrate lemondrop seamlessly with your existing tabletop gearior create on-the-go thanks to a compact design that fits in the palm of your hand.

What Is Included

Nanobox | Lemondrop compact polyphonic granular synthesizer with touchscreen control
MicroSD card with presets and wav files
USB power cord
Type B TRS MIDI To MIDI 5 Pin DIN adapter
Quick Start Guide

Technical Specs

Includes 153 presets and 311 wave files
16 grains per oscillator for a total of 128
Sample memory per oscillator 30 seconds
Power: USB-C connection 5V, 500mA
3.5mm audio input and output
Maximum input and output level: 2Vrms
DAC and ADC resolution: 24-bit
Internal resolution: 32-bit
Sample rate: 48kHz
MIDI Input: 3.5mm Type A/B auto sensing
MIDI Output: 3.5mm Type A/B selectable
Clock Input: 4 PPQ
MIDI support: Note On/Off, Mod Wheel, Sustain, Pitch Bend, Mono & poly Aftertouch, assignable CCs, and clock
H x W x D: 1.5" x 3.75" x 3"
Weight: 0.25 lbs.

Notes: 1010's Nanobox range expands with the Razzmatazz, a tiny drum machine with FM synthesis, sampling and a built-in sequencer. Small but powerful, with built-in MIDI and touchscreen control.

Supplier's Notes:
Create the juiciest beats and tastiest rhythms with Nanobox Razzmatazz, a mini drum sequencer that combines powerful FM synthesis and sampling. Featuring advanced voice architecture, razzmatazz puts a huge range of percussive sounds at your fingertips-from deep and gritty kick drums to searing snare hits and crisp hi-hats. Perform using 8 touchscreen pads or your favorite midi controller, and craft up to 16 rhythms using an innovative visual sequencer that allows you to see all pad states and steps simultaneously. Shape the sound of each pad by combining any variation of two FM oscillators and a WAV file-plus two filters, two envelopes, a resonator, a snap generator, and three additional effects.

You can even choose from four unique types of distortion to create incredibly distinct and powerful drum sounds. Enjoy massive analogue drum sounds and an innovative feature set, all in a compact package that goes anywhere.

Technical Specs

Includes 120 presets and 112 wave files
8 pads that can support 2 FM Oscillators and WAV file each
Sample memory per WAV of 30 seconds
Power: USB-C connection 5V, 500mA
3.5mm audio input and output
Maximum input and output level: 2Vrms
DAC and ADC resolution: 24-bit
Internal resolution: 32-bit
Sample rate: 48kHz
MIDI Input: 3.5mm Type A/B auto sensing
MIDI Output: 3.5mm Type B
Clock Input: 1,2, 4, 8, 12 or 24 PPQ selectable
MIDI support: Note On/Off, Velocity, Pressure, Mod Wheel, Aftertouch, assignable CCs, program changes and clock
H x W x D: 1.5" x 3.75" x 3"
Weight: 0.25 lbs.

What is included:

Nanobox | razzmatazz mini drum sequencer with FM synthesis and sampling
MicroSD card with presets and wav files
Color matched USB power cord
Type B TRS MIDI To MIDI 5 Pin DIN adapter
Quick Start Guide

Notes: Looking to expand your Lunchbox? Look no further! 2hp's Flying Bus Cable is the perfect addition to your ever expanding modular meal. Carrying 8 power slots, expanding your system is a breeze by simply inserting the Flying Bus cable into the extra slot of your Lunchbox power. Did somebody say seconds?!

Flying Bus Cable

8 Slots

Malleable for easy cable management

Double your Lunchbox's modular possibilities

Notes: Just when you thought 2HP couldn't go any smaller, the Zero HP Mult has now arrived! The ZHM a 1 to 5 cable splitter, providing utility outside your case for increased patchabilty. Whether it is sending out a master clock, modulation, or simply lengthening a cable to reach the far ends of your rack, the Zero HP Mult is ready for duty!

Notes: 4ms blank panel - 10HP width. Black coloured PCB material with 4ms logo.

Notes: 4ms blank panel - 1HP width. Black coloured PCB material with 4ms logo.

Notes: 4ms blank panel - 2HP width. Black coloured PCB material with 4ms logo.

Notes: Jumper cable for connecting two Listen 4, Listen 4Q, or Listen IO modules & for daisy-chaining multiple Listens to create a larger mixer. Also used for connecting a WAV Recorder to a Listen module in order to record directly from the Listen's main mix. See the Listen module manuals for details and examples.

One cable connects two modules. By adding more cables you can create a chain between multiple modules.

Specifications:

1x3 pin female header
Pin Spacing: 0.1" (2.54mm)
Total length: 4.38" (111mm)

Notes: Power brick for powering Pods. One power brick can power up to 10 typical Pods. Pods can be daisy-chained using a Barrel Cable or Long Barrel Cable.

15V/3A (45W) / 2.1mm Barrel Plug (5.5mm outer diameter) / Positive Centre.

You also may use your own power brick if it meets the following requirements:

- 15V to 20V DC
- Positive centre 2.1mm barrel plug
- Minimum 20W output power
- Low-noise output
- Compatible with an IEC C5 cable

Please note: IEC cable not supplied

Notes: ***B-STOCK: Box damaged, product in perfect working order***


Power brick for powering Pods. One power brick can power up to 10 typical Pods. Pods can be daisy-chained using a Barrel Cable or Long Barrel Cable.

15V/3A (45W) / 2.1mm Barrel Plug (5.5mm outer diameter) / Positive Centre.

You also may use your own power brick if it meets the following requirements:

- 15V to 20V DC
- Positive centre 2.1mm barrel plug
- Minimum 20W output power
- Low-noise output
- Compatible with an IEC C5 cable

Please note: IEC cable not supplied

Notes: 4ms blank panel - 8HP width. Black coloured PCB material with 4ms logo.

Notes: Power brick for powering Pods. One power brick can power up to 10 typical Pods. Pods can be daisy-chained using a Barrel Cable or Long Barrel Cable.

15-20V / 90W / 2.1mm Barrel Plug (5.5mm outer diameter) / Positive Centre.

Compatible power bricks are available wherever ROW POWER modules are sold. You also may use your own power brick if it meets the following requirements:

- 15V to 20V DC
- Positive centre 2.1mm barrel plug
- Minimum 30W output power
- Low-noise output
- Compatible with an IEC C5 cable

Please note: IEC cable not supplied

Notes: Bus Sticks are low-profile, small footprint power distribution boards for powering up to 13 modules using shrouded (keyed) headers. Simply connect to a Row Power module using the included cable. Attaches to your case using adhesive pads (included) or by drilling and screwing.

Notes: Flying Bus (male pin) are passive power distribution cables that work with the Row Power to distribute power to your modules.

Can be daisy-chained if extra headers are needed. One 14" flying bus cables with 7 male header pins.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod20 is 20HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod20 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod32 is 32HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod32 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod34X is 34HP wide and has extra room to fit even the deepest modules (2.16" / 55mm of available module depth). The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

This Pod requires a power brick (not included).

Or, if you already have a Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain power supplies.

Pods are a perfect way to get started in Eurorack, or add a couple more modules to your monster system!

Made from 100% anodized aluminum, Pods are light, tough and perfect for on-the-go set ups. The power supply can handle up to 1.4A of +12V, which is plenty of juice for even the most modern digital modules. (Or if you prefer to DIY your power supply, Pods are also available unpowered)

Each Pod typically will house one or two modules, but three or more can be accommodated using a multi-power cable accessory.

Mix and match your Pods with desktop synths, effect pedals, drum machines or any musical gear for a flexible modular system. Pods can even daisy- chain with the 4ms Row Power system making them a convenient outboard mini-skiff. Need to add another module? Just add a Pod! Need to pack light for a live set? Just grab the Pods you need and go!

Basic Features:

34 HP Eurorack modular space
Standard M3 threaded holes
100% lightweight anodized aluminum
Built-in Power supply
Red, White, and Blue LED power indicators

Includes:
34HP Pod, black anodized aluminum
Extra deep (2.16"/55mm) fits virtually every Eurorack module
Built-in power supply with four Eurorack power headers
M3 x 8mm pan-head screws, stainless steel (10)
Adhesive rubber feet (4)
Does not include barrel cable or power brick
Power Supply:
Four 16-pin Eurorack power shrouded headers
+12V max 1.4A
-12V max 0.65A
+5V max 1.0A
Power input: Two barrel jacks for daisy-chaining
15V-20VDC, 2.1mm positive tip
Exterior dimensions:
Width: 177.3mm (6.98")
Height: 159.5mm (6.28")
Depth: 57mm (2.24")
Interior dimensions:
Max module depth: 55mm (2.16")
Module width: 34HP
Weight:
0.3 kg = 10 oz

Notes: The Pod40X is 40HP with 2.00" (51mm) of available module depth. The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod40 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: The Pod48X is 48HP with 2.00" (51mm) of available module depth. The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod48X includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod60 is 60HP with 1.34" (34mm) of available module depth. The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod60 includes twenty (20) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod60 Unpowered is 60HP with 1.34" (34mm) of available module depth. No power supply is included, you must supply your means of powering modules with a DIY power supply or a front-facing module such as the Row Power. Two holes on the rear face are plugged with removable plastic plugs, and can be used for DIY applications.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod64X Unpowered is 64HP with 2.16" (55mm) of available module depth. No power supply is included, you must supply your means of powering modules with a DIY power supply or a front-facing module such as the Row Power. Two holes on the rear face are plugged with removable plastic plugs, and can be used for DIY applications.

Pods are a perfect way to get started in Eurorack, or add a couple more modules to your monster system!

Made from 100% anodized aluminum, Pods are light, tough and perfect for on-the-go set ups. Mix and match your Pods with desktop synths, effect pedals, drum machines or any musical gear for a flexible modular system. Need to add another module? Just add a Pod! Need to pack light for a live set? Just grab the Pods you need and go!

Basic Features:

64 HP Eurorack modular space
Standard M3 threaded holes
100% lightweight anodized aluminum

Includes:

64HP Pod, black anodized aluminum
M3 x 8mm pan-head screws, stainless steel (20)
Adhesive rubber feet (4)
Unpowered: requires you to provide your own Eurorack power system
Exterior dimensions:
Width: 329.7mm (12.98")
Height: 159.5mm (6.28")
Depth: 57mm (2.24")
Interior dimensions:
Max module depth: 55mm (2.16")
Module width: 64HP
Weight:
0.42 kg = 14.9 oz

Notes: Right angle 2.1mm barrel plug (5.5mm outer diameter, positive tip). Short barrel to barrel cable for daisy-chaining Row Powers and/or Pods. Cable is 11" long (centre of tip to centre of tip), suitable for two Pods next to each other or in front/behind each other. Also compatible with Row Power modules.

Both ends of the cable have a right-angle plug.

Notes: Medium sized spring reverb tank, Type 8 Accutronics 8BB2C1B with 3×1 springs and medium decay (1.75 - 3 seconds).

Input impedance 190 Ohm, output impedance 2575 Ohm. Input connector insulated, output connector grounded.

Notes: Type 1 - Blue Reverb

Features:
Compact and low cost type
2 natural coil spring type
Input impedance are changeable
Length of connect wire are changeable by optional

Application:
Specially suited for small wattage amplifier
For electric organs, guitar amplifier
Ideally suited for practice amps
2 Springs Type

Notes: Introducing ADDAC's Cable Tester, a desktop utility that provides a reliable means to test the integrity of both mono jacks and ribbon cables, ensuring that every connection is secure and electrically sound.

Individual Wire Testing - Featuring the ability to test each wire within the ribbon cables independently with dedicated LEDs for every wire, providing a clear visual indication of the status of each connection, wires are also tested against their neighbouring wires to detect shorts.

Busboard monitor

The busboard monitor LEDs allows the user to check the state of the busboard power lines as well as the special CV/Gate functions. If the busboard has no +5v supply the led will be off likewise for the CV/Gate functions if not in use.

This is a desktop device, ADDAC provide a long power cable so that it can still be plugged into your rack.

As a safety precaution only power this board when you need to test a cable. Leaving it ON at all times can lead to unintended problematic misuses which, in a worst case scenario, can shorten your Eurorack PSU,

! WARNING !
DO NOT POWER MODULES FROM THE TEST SOCKETS!!

Compatible with all ADDAC System ribbon cables (power, expansions and interconnectivity: 112, 213, 807).

Also compatible with any standard Eurorack power ribbon cable (2x5 to 2x8 or 2x8 to 2x8).

! WARNING !
NOT ALL MANUFACTURERS FOLLOW THESE STANDARDS!
ALLWAYS NOTICE THE ORIENTATION OF THE HEADERS IF YOUR CABLE DO NOT FOLLOW THE STANDARD THEN MOST PROBABLY IS NOT COMPATIBLE.

Tech Specs:
30mA +12V
30mA -12V

Notes: These knobs are custom made for AE modular; they fit perfectly on the shafts and can be added to all AE modules, no matter of which generation they are.

As of December 2020, all AE modules will be shipped with these knobs as standard.

Notes: Expand the lid from your case to be another powered rack. This set includes:

Rails
Handle and handle supports
Powered bus board
Case wiring
AC/DC power adapter
All hardware and thermal tape to complete the conversion

Notes: 104hp wide with two 3U rows and a 1U row.
Powder coated aluminum construction
VESA mount compatible (100mm x 100mm)
Plastic handle for easy mobility
Metal feet can be installed to support multiple angles of jamming.
Secure latching lid with enough depth to keep your patches patched

Expandable

Lid - when you're ready to add more space, the lid can be expanded to be another 104hp x 7U. You can add another set of rails, power supply and power jack and double your available space. (Kit available)
Metal feet - The metal feet can have a pair of rails and rack mounted power added to support another 3U row of 104hp. (Kit available in future)

Connectivity

Audio jacks - set of four jacks for stereo in and stereo out.
MIDI jacks - DIN jacks to support IN, OUT, and THRU MIDI.
USB power - can be used for a lamp to light your case or to charge your phone while recording your set.

Dimensions
557mm x 334mm x 169mm
74mm depth for 1U and bottom 3U row
52mm depth for middle 3U row

Power
+12V - 3A (with plenty of allowance for in-rush current)
-12V - 3A
+5V - 3A (shared with USB power)
36 shrouded power headers

In The Box
Main case
Lid
Metal feet
Power adapter 20V at 6A

Notes: After Later Audio Braided Patch Cables for Eurorack in Gold and Black. One size per pack of five cables. Packs come in 15, 30, 45, and 60 centimeters, or 6, 12, 18, and 24 inches.

Notes: These are 6" (15cm) right angle patch cables for Eurorack. Colour is pink, pack of 5 cables.

Notes: Save space in your rack with stackable cables.

These are the newer shorter stackable Eurorack Patch Cables. Patching is more stable and makes it easier to get a lid on that performance case.

One end of the cable has a male and female jack, the other end as just a male connector. They come in sets of 5 cables.

Available in 6in (15cm), 12in (30cm), 18in (45cm), and 24in (60cm).

Notes: These are right angle patch cables for Eurorack. Size is 12 inch (30cm), colour is green.

Notes: Save space in your rack with stackable cables.

These are the newer shorter stackable Eurorack Patch Cables. Patching is more stable and makes it easier to get a lid on that performance case.

One end of the cable has a male and female jack, the other end as just a male connector. They come in sets of 5 cables.

Available in 6in (15cm), 12in (30cm), 18in (45cm), and 24in (60cm).

Notes: This is a pack of five, 12" skinny patch cable for Eurorack. Colour is green.

Notes: After Later Audio Braided Patch Cables for Eurorack in Gold and Black. One size per pack of five cables. Packs come in 15, 30, 45, and 60 centimeters, or 6, 12, 18, and 24 inches.

Notes: These are right angle patch cables for Eurorack. Colour is blue, pack of 5 cables.

Notes: This is a pack of five, 18" skinny patch cables for Eurorack. Colour is blue.

Notes: After Later Audio Braided Patch Cables for Eurorack in Gold and Black. One size per pack of five cables. Packs come in 15, 30, 45, and 60 centimeters, or 6, 12, 18, and 24 inches.

Notes: These are right angle patch cables for Eurorack. Colour is black, pack of 5 cables.

Notes: Save space in your rack with stackable cables.

These are the newer shorter stackable Eurorack Patch Cables. Patching is more stable and makes it easier to get a lid on that performance case.

One end of the cable has a male and female jack, the other end as just a male connector. They come in sets of 5 cables.

Available in 6in (15cm), 12in (30cm), 18in (45cm), and 24in (60cm).

Notes: These rack screws for Eurorack can be screwed by hand for quick changes, or use a standard Phillips head screw driver.

Each Special Size M2.5 X 8mm stainless steel screw comes with a black nylon washer in a tin.

Notes: Updated with new driver construction and recycled materials, AIAIAI's Studio model is designed for production work and mixing, featuring the same top quality modular design as the brand's other TMA-2 models.

Supplier's Notes:

Signature AIAIAI bio-diaphragm speaker tuned for clarity and detail.

Critically acclaimed sound stage specifically designed for music creation with a clear and highly detailed sound representation.

Enhanced comfort with Alcantara.

Ultra soft over-ear memory foam cushions covered with resilient, CO2 neutral, and highly comfortable Alcantarar ideal for longer sessions.

Versatile.

Trusted for music creativity in all environments - in the studio, on the road, and on stage.

Modular product design.

This TMA-2 modular headphone system offers a customizable solution that adapts to your creative process. With interchangeable components such as earpads, cables, and drivers, you can upgrade or change parts of your headphones to improve sound quality, comfort, or style.

Headphones for life.

AIAIAI offer lifetime trade-in for your headphones or modular parts. With this program, users can leverage the modular product design to get maximum value from their purchase by swapping out used or non-functional headphones or parts for future credit. This means only investing in one pair of headphones, for life.

Signature AIAIAI sound tuned for clarity and detail
Bio-diaphragm speaker for enhanced accuracy
Enhanced comfort with Alcantarar
Responsible modular headphones - headphones for life
High quality cable

Notes: Empowering music creators with the freedom to create wirelessly, TMA-2 Studio Wireless+ features W+ Link with ultra-low latency wireless and lossless audio, Bluetooth 5.0 with +80h playback, and a coiled hi-fi cable.

Free yourself from cables and unleash your creative flow with ultra-low latency wireless headphones.

Create wirelessly with no compromise:

Cable-like performance with ultra-low latency and uncompressed audio via W+ Link technology.

Hear all the details: Clear and natural sound representation tuned for music creation.

Stay in the zone for hours: Enhanced comfort via lightweight build, memory-foam cushions and ergonomic headband.

Go beyond the studio: Switch to Bluetooth mode for everyday listening with +80h playback, or plug directly into a headphone jack with the detachable cable.

Customise, replace and upgrade: The modular nature of TMA-2 Wireless+ allows for endless customisation and easy upgrades or replacements of individual parts.

Ultra-low latency, uncompressed wireless audio TMA-2 Studio Wireless+ delivers uncompressed 44.1kHz, 16-bit wireless audio with only 16ms of latency through the robust W+ Link connection.

Tuned for clarity and detail

Signature AIAIAI bio-diaphragm speaker designed for music creation with a critically acclaimed sound stage and clear, highly detailed sound representation.

Enhanced comfort Soft over-ear memory foam cushions covered with resilient, CO2 neutral, and highly comfortable Alcantarar, ideal for longer sessions in the studio.

Modular product design

These TMA-2 modular headphone system offers a customisable solution that adapts to your creative process. With interchangeable components such as ear pads, cables, and drivers, you can upgrade or change parts of your headphones to improve sound quality, comfort, or style.

Three audio connection modes

Use W+ Link for wireless music creation and studio work with 16 hours of playback Seamlessly switch to Bluetooth 5.0 with +80 hours of playback for everyday listening and inspiration, or plug in to a headphone jack with the included coiled hi-fi cable.

The TMA-2 Studio Wireless+ is a versatile professional headphone, featuring ultra-low latency and uncompressed audio, giving you the freedom to create wirelessly without compromising sound. Designed for today's dynamic creative workflow, it features enhanced comfort for long sessions and a clear and detailed sound representation. Featuring new W+ Link technology, added Bluetooth 5.0 with +80 playback, and a coiled hi-fi cable.

Packaging

Items per master: 10
Packaging weight (g): 664
Packaging width (mm): 235
Packaging height (mm): 210
Packaging depth (mm): 85
Product weight (g): 270

Specifications

Driver diameter (mm): 40
Resonance frequency (Hz): 80
Frequency range: 10Hz - 40kHz
Sensitivity (db @ 1mW): 97
Impedance (Ohm): 32
Rated power (mW): 40
Max power (mW): 100
Diaphragm material: Bio-cellulose
Magnet type: High-grade N45 Neodymium
W+ Link audio quality
Uncompressed 44.1kHz 16-bit
W+ Link operating range (m): 12
W+ Link latency (ms): 16
W+ Link headband playback time (hours): 16
W+ Link transmitter playback time (hours): 30
W+ Link transmitter charging time (hours): 3
W+ Link transmitter input: 3.5mm/6.3mm TRS jack
Bluetooth codec: AAC, SBC
Bluetooth version: 5
Bluetooth profiles: A2DP
Bluetooth operating range (m): 10
Charging time (hours): 3
Number of talk mics: 1
Talk mic frequency range: 100Hz - 10kHz
Responsible design: Main material
Speaker Units: Recycled ABS. Headband: Silicone + Recycled ABS. Earpads: Alcantara + PU foam.

Packaging material

Sleeves: Recycled paper, outer sleeve cradle-to-cradle certified. Bags: Recycled plastic.
Design for disassembly: Yes
Right to repair compliant: Yes
Repair parts available: Yes
Repair guides available: Yes

Notes: AIAIAI's affordable XE range might just offer the best value studio headphones around. Balance S01 drivers and comfortable E04 ear pads are paired with a slim headband for great sound at a reasonable price.

Supplier's Notes:
Modular studio headphones.

Balanced and detailed sound
Enhanced comfort over-ear cushions
High sound isolation
Weighing only 190g
Modular headphone design

Modular studio headphones with highly detailed sound and full bass extension, balanced for music production. Comfortable PU leather over-ear earpads provide high isolation, reducing surrounding noise when creating on the go. Weighing only 190g for enhanced comfort over extended periods of time.

Balanced detailed sound

Critically acclaimed sound stage specifically designed for studio use with a clear and highly detailed sound representation.

The speaker unit contains a bio-cellulose diaphragm made from bacterial cellulose, an organic compound grown using certain types of bacteria. The precision-grown diaphragm from bio-cellulose is stiffer, lighter, and stronger than regular PET speaker units, allowing the sound-producing diaphragm to vibrate without the levels of distortion found in other speakers.

Each of these qualities results in more accurate and detailed sound from the speaker with the ability to retain clarity of sound at high volumes.

With a minimal and lightweight construction of only 190g, the TMA-2 Studio XE is ideal for the flexible, versatile and dynamic workflow of modern music makers.

Lightweight & comfortable

High grade over-ear memory foam cushions covered in resilient and soft PU leather, for enhanced comfort during long creation sessions or live performances. The over-ear cushion design provides high sound isolation when creating in noisy environments.

Headband made from high grade nylon combined with durable PU leather earpads, results in a total headphone weight of only 190g.

In the box

S01 . Balanced sound - Bio-diaphragm

Engineered with a 40mm speaker diaphragm made from stiff bio-cellulose to reduce distortion and increase transparency. Tuned for a balanced, accurate sound. Balanced sound - Bio-diaphragm.

H01 . Slim - PU foam

Slim and lightweight polycarbonate headband with soft, durable PU foam padding.

E04 . Over ear - PU leather

Soft over-ear memory foam cushions covered with PU leather. The thickness and materials provide better comfort and excellent isolation. Adding a low end boost for a warmer sound with powerful dynamics.

C05 . Straight - 1.5m - Adapter

Straight black 1.5m thermo plastic cable with soft touch surface. Comes with 1/4 to 1/8 screw-on adapter.

Headphones for life

As a music creator, you need headphones that can keep up with your evolving needs and styles. These TMA-2 modular headphone system offers a customizable solution that adapts to your creative process. With interchangeable components such as earpads, cables, and drivers, you can upgrade or change parts of your headphones to improve sound quality, comfort, or style.

By investing in this modular headphone system, you're not just buying headphones - you're investing in a long-term solution that evolves with your music. This reduces electronic waste while ensuring that you always have the optimal headphones just for you.

Diaphragm: Bio-cellulose
Driver diameter: 40 mm
Impedance: 32 Ohm
Magnet: High-grade Neodymium
Max power: 100 mW
Rated power: 40 mW
Resonance freq: 80 Hz

Notes: Make music where you are most creative with portable, wireless studio monitors.

Seamlessly bring your studio sound to your most creative spaces. Portable studio monitors with 20 hours of battery life and reference monitor performance. Precise and neutral sound representation tuned for music creation and critical listening. Enjoy a cable-free set-up where you can quickly reposition to always find yourself in the sweet spot, enabled by ultra-low latency and uncompressed wireless audio. Play music from any device via Bluetooth or cable directly to a mixer, audio interface or other audio source. Built responsibly with 100% recycled plastics, and future-proof designed for easy disassembly and component replacement.

Bring your studio sound with you: Studio monitors designed for portability with 20 hours of battery life, robust design and lightweight build.

Experience reference monitor performance wherever you are: Precise and neutral sound representation with bass extension down to 40Hz, tuned for music creation and critical listening.

Seamless, cable-free set-up: Quickly reposition to always find yourself in the sweet spot, enabled by ultra-low latency and uncompressed wireless audio.

Connect to everything: Play music from any device via Bluetooth or cable directly to a mixer, audio interface or other audio source.

Reduce your environmental impact: Built with 100% recycled plastics, and designed for easy disassembly and component replacement.

Shape UNIT-4s sound to your environment from your phone: Choose from predefined sound profiles or micro-adjust the customisable 5-band EQ with the UNIT-4 mobile app.

Packaging

In the box:
UNIT-4 Wireless+ (2 pcs)
UNIT-4 Power Supply (2 pcs)
UNIT-4 Protective Pouch (2 pcs)
X02 W+ Link transmitter (1 pcs)

Items per master: 1
Packaging weight (g): 8200
Packaging width (mm): 332.5
Packaging height (mm): 331
Packaging depth (mm): 205
Product weight (g): 6144
Product width (mm): 156
Product height (mm): 258
Product depth (mm): 114

Specifications

Frequency range: 40Hz to 40kHz (-10dB)
Frequency response: 50Hz to 20kHz (+/-2dB)
W+ Link audio quality: Uncompressed 44.1kHz 16-bit
W+ Link operating range (m): 12
W+ Link latency (ms): 16
Bluetooth codec: SBC, AAC
Bluetooth version: 5.2
Bluetooth profiles: A2DP 1.3, AVRCP 1.6
Charging time (hours): 2
Peak SPL (dBSPL): 105
Self generated noise: <20dB
THD: <1% nominal, <10% peak output
Power supply: ACDC Converter, 120/240V to 20VDC 120W
Playback time on battery (hours): 20
Battery capacity (Wh): 77
Enclosure type: 2-way bass reflex
Woofer: 4-inch high excursion paper cone woofer
Tweeter: 1-inch silk dome tweeter
Amplifier power: 2 x 30W continuous, 2 x 80W peak
Amplifier type: Class D
DSP: Loudness adaptive bass boost
Crossover frequency (kHz): 3
EQ adjustment: 5-band adjustable EQ via AIAIAI app
Analogue inputs: 3.5mm mini-jack + 6.3mm TRS balanced
Grill material: Steel

Responsible design

Main material: 100% recycled plastics, post-consumer
Packaging material: 100% recycled paper and cardboard, FSC certified
Protective pouch material: 100% compostable fabrics
Design for disassembly: Yes
Glue-free design: Yes
Right to repair compliant: Yes
Repair parts available: Yes
Repair guides available: Yes