Back catalogue: Studio Equipment

Notes: Erica Pico RND is combined LFO/random source module.

It generates sine LFO waves, white noise, S&H CV and some interesting stuff - random triggers and pulse wave with random duty circle; basically, everything, you need, to bring some uncertainty in your modular setup.

The Pico RND comes equipped with five outputs, they emit the following signals:

- Sine waves
- Pulse waves with varying width
- Random triggers
- Sample and hold material
- White noise

The speed of LFO and S&H circuit can be edited using the module's potentiometer (Range: 0.1 Hz to 20 Hz). For synchronizing the Pico RND with other gear, a clock input was implemented.

Notes: Erica Pico VC EG is versatile looping AD/ASR envelope generator with voltage control over attack and decay times. It has automatic Trigger/Gate detection, as well as "drone mode" - at full CW setting of the Decay knob, the envelope is full open. In the LOOP mode you can re-trigger envelopes for even more interesting modulations.

Features

AD/ASR envelope
Automatic Trigger/Gate detection
Manual and voltage control over
Attack and Decay time
Manual trigger button
Input protection against over-voltage
Protection against reverse PSU connection
Output amplitude 0V - 10V
Attack time 5ms - 1s
Decay time 5ms - 50s
CV level (Full span) -5V - +5V
Power consumption +17MA, -13MA
Module width 3 HP
Module depth 35 mm

Notes: Erica Pico VCF1, is a younger brother of Erica Black Polivoks VCF, designed on the similar topology using rare Russian op amps. As result you get a filter great for acid bass lines, screaming resonance sweeps and deep wobbles.

Features:
- Lowpass and bandpass modes
- Self oscillation
- Rare russian opamps used
- Input protection against overvoltage

Dimensions
3 HP
35 mm deep

Current Draw
12 mA +12V
11 mA -12V

Notes: Erica Synths Pico VCO 2 - powerful, full analogue VCO with great tracking over 8 octaves just in 3HP! Combine two of those, add some PWM and have a sound of real analogue beast!

Features:

Manual TUNE and PWM controls
+-1 octave switch
1V/oct input with good tracking across 8 octaves
PWM CV input
Pulse and triangle waveform outputs
Input protection against overvoltage
Protection against reverse PSU connection

Technical specification:

Output signal amplitude: -5V - +5
PWM CV input (full span): -5V - +5V
Power consumption: +21mA, -19mA
Module width: 3HP
Module depth: 35mm

Notes: Erica Synths Pico VCO is a great, deep sounding VCO with 32 selected waves: classical, fattened with sub-oscillator, FM synth and others.

Features
2 banks, 16 waves each
VCO/LFO mode
Voltage controlled wavesurfing
Wave morphing in LFO setting
Typically you would need several rather expensive modules to generate similar sounds, besides there's an extra feature: flip a switch, and you have a versatile LFO.

With Pico Series we challenged ourselves - can we make ANY superior functionality synth module 3HP wide and affordable? Yes, we can.


Technical specification:

VCO frequency range: 30Hz - 5kHz
LFO frequency range: 0,1Hz - 20Hz
1V/Oct input signal amplitude: 0V - +10V;
Output amplitude: 10V ptp
Power consumption: +26 mA, -4 mA
Module width: 3HP
Module depth: 35 mm

Notes: Erica Synths Snare Drum is developed in collaboration with the French company e-licktronick and it's our take on analogue snare drum circuits adapted for modular systems. Sharp, punchy sounds, Accent & CV control over key parameters of the module make it distinctively expressive in studio and live performances.

Features
Tune, Snappy, Noise tone and Decay controls
CV control with attenuators over Tune and Decay
Manual trigger
Accent for better expression

Specifications
Decay range: 150ms - 260ms
Audio output level: -5...+5V
CV level (full span): -5 - +5V
Accent CV level: 10V
Trigger level: 5V
Trigger time: 1ms
Power consumption: 37mA@+12V, 35mA@-12V
Module width: 10HP
Module depth: 35mm

On this run of modules the Pitch & Decay CV inputs are inverted: rising CV will decrease pitch, falling - increase.

Notes: Everything sounds better with compression - whether you need a bit of extra pressure for your drum sounds or just that extra touch to make your modular mix more nimble and tight, the Erica Synths Stereo Compressor will make your live performances a joy. The module is optimized for percussion sounds and will be a great addition to any Erica Synths Drum module rig. The Stereo sidechain can be used to animate melodic layers on the beat and to truly bring your Basslines to life.

Features

THAT chip-based stereo compressor
DC coupled sidechain
Gain, Threshold and Compression Amount (Ratio) settings
Stereo Link for level detectors
Bypass switch
8 segment output level VU meter

Specs

Audio input level -5...+5V
Threshold -40dB to +10dB
Makeup gain -12dB to +12dB
Ratio 1:1 to 8
Power consumption +60mA, -22mA
Module width 10HP
Module depth 35mm

INPUT LVL; Adjust the input signal level to your taste
GAIN; This knob adjusts the makeup gain of the compressor
THRESHOLD; Set the compressor threshold
COMP. AMT;This knob adjusts the compression ratio
STEREO LINK; Sending hard-panned or significantly different audio levels on the left and right channels into the audio inputs may result in undesired left-right panning on the output of the compressor, because the level detectors on each channel will ensure a different amount of compression. With the STEREO LINK switch on, the level detectors on both channels are merged and the min/max function is engaged. This ensures equal compression on both channels.
PROCESS; The bypass switch allows for turning off the compressor instantly
8 SEGMENT VU METER; 8 segment VU meter gives a visual reference of the output signal
IN L / IN R; These are the L and R audio inputs
OUT L / OUT R; These are the L and R outputs of the module
SIDE IN L / SIDE IN R; These are L and R sidechain inputs. You can process each channel individually
SIDE OUT L / SIDEOUT R; These are the sidechain signal outputs - they are buffered copies of the sidechain inputs

Notes: Erica Synths MIDI to Trigger module lets you control your drum modules and trigger events on your modular from any MIDI sequencer!

If you want to use a MIDI sequencer to trigger events on your modular synthesizer (e.g. using the hexinverter.net Mutant drums range or Tiptop Audio classical drum modules or envelope generators to control VCAs), Erica Synths MIDI to Trigger module is just what you need, it converts ANY MIDI notes to eight 10ms Trigger signals.

When designing the module, Erica Synths put usability as priority; it will take you seconds to program the module. It works with any MIDI sequencer & controller so there is no need to change MIDI controller settings, instead, you reprogram the module.

Notes: Classy stuff from the London label's debut collab with one of our favourite synth brands. Classy stereo delay with analogue filtering and creamy valve distortion. Perfect for studio or live use.

Supplier's Notes:
Ninja Tune - an English independent record label based in London and Erica Synths have teamed up to create a custom dub delay effects unit, the Zen Delay.

Features
Controls: delay time, feedback, delay mod (5 presets), tap button, dry/wet, bypass switch, filter cutoff, resonance, drive, input level, filter mode

Inputs
Stereo In: 2x standard jack

MIDI In: standard MIDI socket

CV In: standard jack

Outputs

Stereo Out: 2 x standard jack

Delay times: 1-5000ms with 1/8...x8 of clock/tap rate in beat mode

Inspired by a trip to Berlin's trailblazing music hardware trade show Superbooth, Coldcut's Matt Black and longtime friend Dr Walker (Liquid Sky artist collective / Air Liquide) envisaged the exciting possibilities of a custom hardware effects unit. The result is the creation of the Zen Delay i the first-ever hardware effects unit produced in collaboration with an electronic music label.

Bringing together the best of the digital and analogue worlds, the Zen Delay is a BPM-synced stereo delay line, combining extreme feedback ranges for dub and experimental lo-fi effects with a multi-mode 24 dB synth filter and valve overdrive.

Created and manufactured by Erica Synths, the unit is housed in a metal case with Erica Synths' signature bakelite knobs and a valve circuit for extra analogue warmth. While sonically versatile, it is incredibly easy to use each function has a physical knob that you can play around with without diving into manuals or scrolling through menus on a tiny screen.

Crafted in close collaboration with DJs and producers, the Zen Delay was uniquely developed with both live and studio use in mind and is suitable for many different performance situations, musical styles and instruments. While most delay devices are designed as 'stomp boxes' for guitarists, the device is equally powerful in the hands of electronic music producers, artists and DJs, adding a unique, warm and powerful sonic character to drum machines, loops, vocals, synths, samples or any other source. Even full tracks or a live stereo mix can be enhanced by the combination of analogue and digital circuitry, breathing new life into iPad performances and giving traditional digital synths and drum machines a huge kick.

The Zen Delay is a product of our expertise on vacuum tube designs, our powerful, custom DSP platform and the great sound of our filter ICs made and developed in Latvia. It by far exceeded expectations in terms of how it sounds and feels when played. - Girts Ozolin

The Zen Delay is the analogue delay unit I've been waiting for. Stereo warmth, tone and texture. Perfect for live abusage, and studio madness love it - The Bug

The Zen excels at the sort of extreme dub possibilities Coldcut love. Feed it back! - Matt Black

For years I have dreamed of a state-of-the-art stereo valve dub delay for my MPC that perfectly masters all sound aesthetics from "badass" to "psychedelic hypnotically trashed" and now, have a look! There it is... the Zen Delay! - Dr Walker

Power: 12v (power supply for worldwide use is included)
In/Out levels: 3.2v peak to peak
DAC
114 dB dynamic range

-100dB THD+N

ADC
108 dB dynamic range

-98 dB THD+N

Dimensions: 21 x 15 x 5 cm
Weight: 870g

Notes: Based on the excellent LXR-02 drum machine, the LXR Eurorack module is a percussion all-round, with six voices, trigger inputs and CV modulation, plus the ability to generate synth parts. Versatile.

Supplier's Notes:
LXR eurorack module is a compact and great-sounding percussion synthesizer based on the sound engine of the LXR-02 drum machine. While retaining the core interface of the LXR-02, this module adds the essential eurorack ingredient - assignable CV control over parameters and many more tweaks in the user interface for better integration in any eurorack system

Features

6 drum/percussion voices
7 trigger inputs with accents
5 assignable CV inputs
4 assignable outputs
3 voices can be used as basslines due to 1V/oct tuning
Over 30 adjustable parameters per voice
Insert FX section
Kit memory
SD card for Kit exchange and easy firmware updates
Kits compatible with the LXR-02

Dimensions
28 HP
35 mm deep

Current Draw
88 mA +12V
10 mA -12V
0 mA 5V

Notes: A unique graphical take on an oscillator design, E-RM's brand-new polygonal synthesis approach is unlike anything else we've seen. Stereo oscillator capable of a huge range of timbres. Innovative stuff.

Supplier's notes:
The polygonal synthesis is a kind of graphical complex amplitude shaping method. With the help of the built-in modulation sources, polygonal synthesis in polygogo opens up a wide range of sonic possibilities from clicky pinged sequences to unique dark thunderstorms, bass lines, leads and colored noise.

This mighty stereo oscillator impressed the audience with its wide range of possible timbres. The idea of sculpting a shape on the screen of the module that then translates into sound works really well and invites the user to interact with the module.

Notes: The CP3PLUS is an accurate recreation in Eurorack format of one of the most appreciated vintage modular audio mixers. The specific distortion makes it not only a great summing unit but also a great sound design tool. The included MULTI is a welcome bonus.

Tech specs:

-width 10HP
-22mm depth behind the panel, including the power connector
-4 mono analog input
-4 input level pots
-1 dual level pot
-one inverting and one non-inverting output jacks
-one 4 jack passive multiple
-standard 10 pin euro power (+12V / -12V)
-power consumption +12V 23mA -12V 25mA

Notes: This is probably the fastest envelope generator in Modularland.

Why? Because it is based on the fastest one. The classic Japanese modular from the seventies everyone loves.

Tech specs:

- Panel width 6HP
- 35mm depth behind the panel, including the power connector
- 4 control pots : Attack, Decay, Sustain, Release
- 1 gate switch : triggers ADSR cycle
- 1 time switch : switches between fast and slow envelope times
- One normal and one inverting output jack 8V peak
- Standard 10 pin euro power +12V/-12V
- Power consumption +12V 20mA , -12V 15mA

Notes: This is an envelope generator based on the SMD AS3310.

The AS3310 is a modern recreation of the classic Curtis CEM3310 chip, used in many famous mono and poly analogue synth from the eighties.

Feedback took the best ideas from all the classic 3310 circuits and tried to squeeze the maximum from this fantastic chip.

Tech Specs :

- Panel width 6HP
- 35mm depth behind the panel, including the power connector
- 4 control pots : Attack, Decay, Sustain, Release
- 1 gate switch : triggers ADSR cycle
- 1 mode switch : Normal (ADSR), Damp (ADRR), Auto (ASR)
- 1 re trigger input
- One normal and one inverting output jack 10V peak
- Standard 10 pin euro power +12V/-12V
- Power consumption +12V 55mA , -12V 16mA

Attack Time 2.5ms-1.5s
Decay Time 6ms-4s
Sustain Level 0-10V
Release Time 6ms-4s

Notes: This is an envelope follower based on a classic module from the seventies but with some improvements to suit modern needs.

The IN signal is bifurcated to the envelope follower circuit and also to a THRU output, so the original signal is also available for external processing.

The envelope follower has three controls, a switch to select response time (fast, medium, slow), a pot to adjust GATE threshold and a pot to adjust the envelope CV level.

This little module will help you shape the timbre and/or the level envelopes of your sounds. From dynamic envelope filtering to compressor like side chaining there are lots of possibilities to mangle your audio.

Tech specs:

- 4HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 18mA , -12V 16mA

Notes: This little module is an evolution of the LFO of the famous MS monophonic synth from the seventies, adapted to eurorack format.

Tech specs:

4HP width
35mm depth behind front panel including the power connector
2X control pots for FREQUENCY and WAVEFORM

1X FREQUENCY RANGE switch: LOW and HIGH
LOW - 18mHz (55sec) - 0,7Hz (1.4sec)
HIGH - 0,63Hz (1.6sec) - 24Hz (42msec)

2X outputs : SQUARE 0/10V Vpp and TRIANGLE -5V/5V Vpp
standard 10 pin euro power +12V / -12V
power consumption +12V 20mA , -12V 15mA

Notes: LinMix is a compact 6HP mixer suitable for audio signals and modulations CVs.

It is not AC coupled.

Tech specs:

-width 6HP
-42mm depth behind the panel, including the power connector
-standard 10 pin euro power (+12V / -12V) (works also at +15V / -15V)
-power consumption +12V 5mA , -12V 5mA

Notes: MIX KM (like Feedback's PRE KM channel strip) is based on a famous late seventies small mixer used by many electronic music bands.

Tech specs:

- 35HP front panel
- 35mm depth behind front panel including the power connector
- 6 mono input jacks ( 1 per channel)
- Pot controls for channels : Gain, Hi, Low, Aux1 send, Aux2 send, Pan, Volume
- 6 mute switches (1 per channel)
- Pot controls for master : Master Level, Headphone Level, Aux1 Return, Aux2 Return
- 2 x mono aux send jacks
- 4 mono input jacks for two stereo Aux returns
- 2 jacks for master left and right out
- one 3.5mm stereo jack for headphone out
- boxed 10 pin euro power (+12V / -12V)

Notes: A premium headphone amp module capable to drive low and high impedance phones to high enough SPL, with good dynamic range and very low distortion.

Tech specs:

- Panel width 6HP
- 35mm depth behind the panel, including the power connector
- 1 control pot : Phones Level
- 1 mode switch : Switch from stereo to mono for both channels
- 2 input jacks
- 1 stereo output jack
- standard 10 pin euro power +12V/-12V
- power consumption +12V 100mA , -12V 50mA

Notes: SQUEEZE2 is the improved variant of SQUEEZE:

- SMD transistors are changed to matched through hole ones
- all capacitors are now through hole Panasonic LowESR
- added trimming circuit to adjust 0 gain for the center of make-up gain pot so the SQZ will have 0 amplification on middle adjustments

4HP Compressor designed for continuous adjustment of gain, threshold and compression ratio with a single potentiometer.

There is also a knob for input level and a knob for make-up gain.

The module is based on high-performance THAT4305 Blackmerr VCA chip.

Tech specs:

-width 4HP
-35mm depth behind the panel, including the power connector
-1 audio input : IN
-1 audio level pot : INPUT
-2 control pots : LESS/MORE (compression), MAKE-UP Gain
-1 output : OUT
-standard 10 pin euro power +12V / -12V
-power consumption +12V 25mA -12V 25mA

Notes: The STATIC module is a comprehensive collection of noise sources generated with different methods.

Tech specs:

-width 10HP
-38mm depth behind the panel, including the power connector
-2 control pots : MORPH, SPECTRUM
-1 switch : spectrum type TR/CHIP
-8 outputs : MSWHITE, MSPINK, ZNWHITE, ZNPINK,
DARK, MORPH, TROUT, RNDVOLT
-standard 10 pin euro power +12V / -12V
-power consumption +12V 35mA , -12V 30mA

Notes: As the name suggests this module can produce sub frequencies of -1 and -2 octaves relative to the square wave signal provided at the input jack.

But this is not just a simple SUB generator. It also has a little mixer that will let you add different levels of -1 and -2 octave signals to the original square wave. You can select the -2 octave signal to be a square wave or a pulse wave.

The module has individual outputs for the mixed signal, the -1 octave and the -2 octave.

This little modules can produce enough timbral variation to make you bass sound exciting.

Tech specs:

- 4HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 12mA , -12V 9mA

Notes: VCA2600 needs no introduction. The best sounding VCA in 4HP with matched and thermo coupled transistors.

Tech specs:

-width 4HP
-35mm depth behind the panel, including the power connector
-standard 10 pin euro power +12V / -12V
-power consumption +12V 25mA -12V 25mA

Notes: This filter is based on the classic 2600 from the seventies and uses the LM3900 Norton opamp chip.

It has an audio inputs, two CV ins and an audio out.

You can control audio input level, CV levels, frequency cutoff and resonance.

It has a beautiful sound and it can go from relatively clean to dirty and screamy depending on audio signal level and resonance.

Tech specs:

- 8HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 7mA , -12V 13mA

Notes: The Airlectron Sensor Recorder module is equipped with a sunlight independent distance sensor to generate CV output voltages.

A distance sensor reacts to hand movements and varies the CV output voltages (bipolar/max +/- 5 V, unipolar/max 0-+10 V). The range control adjusts the detection distance (2-50 cm). The freeze function keeps the voltage when there is no continuous movement.

The recorder/looper can be used to record motion sequences for up to two minutes. This recorded data can be played back in a loop or once and restarted at the START/RESET input. LEDs indicate the status of the gate inputs and outputs.

Features:

3x controller
1x Vishay distance sensor
3x gate/trigger in- and outputs
2x CV outputs unipolar/bipolar
Power supply via Doepfer connector

Notes: The C-1U module is a one-channel module for recording and playing back movements of controller. Those can be recorded with channel's knob. The movements will be output as control voltage. The record time amounts to one minute maximal.

The track can be played once only (one shot) or in loop. The speed of the play back or the output offset is controllable with the pot. There are an additional CV input for CV recordings and a reset input.

The track data remains permanently stored when a 3V battery is used to buffer the RAM. When the module is switched on, the recorded data is available again. The module can be operated unipolar or bipolar (set by jumper on the back).

Note: The C-1U KnobRekorder uses a standard 3v lithium backup battery , type CR2032. The battery is needed to keep recordings and settings stored when the Eurorack case is turned off.

Dimensions: 12 HP
Power consumption: 20mA at +12 V and 9mA at -12 V

Module is a 1U tile.

Notes: Up to eight voices of digitally synthesised drums, percussion and synth sounds from this versatile module, featuring virtual analogue models as well as FM and wavetable options.

Supplier's Notes:
Flame "Fire" percussion synth module

The module is a full 8-way polyphonic drum and percussion synthesizer. It offers different digital synthesis algorithms, which can be distributed over 8 channels. The sound engine delivers virtual analog sounds as well as different digital percussion sounds, which are generated with FM, wavetable or virtual analog synthesis. It is also possible to create sim- ple monophonic bass or synthesizer voices.

During development, particular attention was paid to direct and simple usability with regard to live operation. The hardware essentially consists of two parts (which are deli- vered together). On the one hand there is the basic module with all controls, the display, connections for MIDI, 2x CV inputs and 5 audio outputs.

There is also a separate XFIRE I/O extension with sockets for the 16 analog trigger/gate/CV inputs and 3 additional audio outputs. Both modules are connected via a 60cm long ribbon cable. In this way, the XFIRE module can be installed anywhere else in the rack. The base module is therefore only 22TE wide and can also work alone without the extension as a MIDI expander.

A maximum of 8 audio outputs are available. A stereo pair (outputs 7+8), plus 6 additio- nal individual direct outputs. All outputs are freely configurable. Two pages with settings for panorama and volume are available for the stereo main out.

There is a gate/trigger input and a configurable CV input for each channel. Two additio- nal programmable CV inputs can be used for further controls. Regardless of the analog connection, the module offers full MIDI functionality. Two MIDI inputs and a MIDI output/softthru allow integration into an external MIDI setup. The firmware can be upda- ted via MIDI Sysex. The created KIT data can also be saved or exchanged.

Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


Up to eight voices of digitally synthesised drums, percussion and synth sounds from this versatile module, featuring virtual analogue models as well as FM and wavetable options.

Supplier's Notes:
Flame "Fire" percussion synth module

The module is a full 8-way polyphonic drum and percussion synthesizer. It offers different digital synthesis algorithms, which can be distributed over 8 channels. The sound engine delivers virtual analog sounds as well as different digital percussion sounds, which are generated with FM, wavetable or virtual analog synthesis. It is also possible to create sim- ple monophonic bass or synthesizer voices.

During development, particular attention was paid to direct and simple usability with regard to live operation. The hardware essentially consists of two parts (which are deli- vered together). On the one hand there is the basic module with all controls, the display, connections for MIDI, 2x CV inputs and 5 audio outputs.

There is also a separate XFIRE I/O extension with sockets for the 16 analog trigger/gate/CV inputs and 3 additional audio outputs. Both modules are connected via a 60cm long ribbon cable. In this way, the XFIRE module can be installed anywhere else in the rack. The base module is therefore only 22TE wide and can also work alone without the extension as a MIDI expander.

A maximum of 8 audio outputs are available. A stereo pair (outputs 7+8), plus 6 additio- nal individual direct outputs. All outputs are freely configurable. Two pages with settings for panorama and volume are available for the stereo main out.

There is a gate/trigger input and a configurable CV input for each channel. Two additio- nal programmable CV inputs can be used for further controls. Regardless of the analog connection, the module offers full MIDI functionality. Two MIDI inputs and a MIDI output/softthru allow integration into an external MIDI setup. The firmware can be upda- ted via MIDI Sysex. The created KIT data can also be saved or exchanged.

Notes: The module can record the joystick movement up to a length of over a minute. The sequence remains stored in the battery-backed RAM after switching off. When playing the sequence, it can be manipulated in speed and playback direction.

There is a FREEZE function to hold the current joystick position plus an external reset input. In addition, a GATE is set during movement and a CV voltage is output as a function of the joystick movement. The ranges of the X / Y output voltages are bipolar +/- 5v or unipolar from 0 to + 10v. Both channels X and Y have a passive attenuator potentiometer, so that the voltage range can also be set lower.

Notes: The "uMCLK Divider" module can either work as a MIDI clock divider or as an analog clock divider. The divider outputs are assigned differently in both operating modes.

After receiving a MIDI start command, the module works as a MIDI clock divider. There are fixed dividers on 11 outputs. Via the divider output KEYS, triggers can be triggered and mixed via MIDI notes. The keyboard zone extends over three octaves. With the help of the LEARN key, the receive MIDI channel and the lowest note of this 3-octave range can be defined.

When stopped (i.e. after receiving a MIDI stop command or after switching on), the module works as an analog clock divider and divides the analog clock present at the CLOCK input. The 12 analog divider outputs can be reprogrammed via SYSEX. Ready-made SYSEX files are already available (e.g. for even / odd dividers, Fibonacci series, offbeats, etc.). The RESET input resets the analog counters or serves to deactivate the analog divider.

Connections:
- Ribbon cable adapter for Doepfer bus +/-12Volt
- Inputs: 2x Clock/Gate,Reset (0/+5..10V), 1/8th inch mono jacks
- 1x MIDI (TRS-B standard) 1/8th inch stereo jack Outputs: 1x MIDI (TRS-B standard) 1/8th inch stereo jack
- 14x Clock/Gate Divider, 1/8th inch mono jacks

Control elements:
- 1 push button with LED (LEARN key) 16 LED's
- Current consumption: max. +70..80mA / - 0 mA
- Size: Euro rack format 3U / 6HP 30x128,5x40 mm

Dimensions
5 HP
40 mm deep

Current Draw
80 mA +12V

Notes: The "uMM" combines a MIDI merger and two independent THRU distributors in a module that is only 4 HP wide. All sockets on the module are in MIDI TRS-B format.

At the heart of the two-input MIDI merger is a small, powerful ARM processor with plenty of buffer memory. Two MIDI streams are mixed to one output and can also be tapped via an additional second output. Two LEDs signal the operation of the merger: one LED indicates MIDI activity at the inputs, and a second LED warns of too much data at the inputs.

The second group of functions consists of two independent, separate MIDI THRU distributors. The MIDI data at the respective MIDI input can be picked up and distributed at the three THRU outputs. If required, a 1-to-5 distributor can be created from the two units by connecting an output of the left group to the input of the right group.

Features:

4x MIDI IN (TRS-B)
2x MIDI-OUT (TRS-B)
6x MIDI-THRU (TRS-B)
Powered via Doepfer connector

Notes: The 333 is a summing and distribution module for Eurorack modular systems.

It is composed of three identical sections, the red, yellow and green, each of those featuring three inputs summing amplifier with three independently buffered outputs.

Derived directly from the CGM creative mixer series, the sum section is DC coupled, allowing the sum of control voltages as well as audio signals.

With an extremely low tolerance in both sum and output sections, it is suitable also for summing quantized voltages like the ones coming out from the quantized outputs of the SAPEL.

In case CVs or audio signals are particularly hot, the 6dB attenuator might be helpful to reduce exactly by 50% the incoming signals.

Red and yellow output are also normalled to the 1st jack socket of the yellow and green input: in this way this module can also work as a 1 to 9 buffered multiple.

Notes: Oof. Frap casually serve up one of the best filters we've seen in a long time. Quad multimode circuits with saturation and feedback give you extensive routing options. Delicious.

Supplier's Notes:
cunsa /'cu?nsa/ s.f. [dialect of Modena of uncertain etymology, probably from a Latin *comptiare, derived from comptus, participle of comere 'organize,' 'decorate'] i curing, seasoning (of foods), tanning (of leathers).

Seasoning is crucial for cooking. It is a process that enhances the flavors, glues the ingredients together, and even adds some unexpected kick.

From a gentle refining touch to a shovelful of spice, CUNSA is the perfect seasoning tool for your patches. It can sweeten a sour lead or beef up an insipid bass line, and anything in between.

And, just like a good oil, you can even taste it by itself!

CUNSA is a quadruple analog pingable multimode resonant filter, saturator, mixer, and oscillator.

It is Frap Tools' sound seasoning tool: it can gently even a patch, applying a final touch, or it can set it on fire with a ridiculous amount of spice. It's up to you and your cooking style!

It consists of four multimode resonant filters with a custom saturation and feedback control that you can use independently or in various combinations and roles thanks to a series of seminormalizations.

Four Analogue Resonant Multimode Filters

CUNSA features four state-variable filters that can be used independently or linked and mixed. Each filter provides three behaviors simultaneously: lowpass, bandpass, and highpass. Each behavior has a 12 dB/oct slope, except for the lowpass, which can be either 12 or 24 dB/oct.

Unique 'Character' Circuit for Feedback and Distortion

CUNSA handles feedback and gain staging with extreme control and versatility. Besides the usual Q control that emphasizes the cutoff frequency, the Character circuit defines the amount of soft clipping when the filter overloads. High clipping guarantees a controlled behavior with fat tone and pure resonance, while low or no clipping lets the signal saturate the filter stages and make it scream.

V/oct Tracking and Quadruple Oscillator

Each filter responds to the V/oct signal with excellent tracking. It is thus possible to move the cutoff frequency along with the main melody or make CUNSA resonate with no input and transform it into a multiple oscillator. The V/oct inputs are seminormalled so you can control more filters with the same CV. Easy chords stabs!

Ping and Ring

CUNSA is ideal for percussive and organic tones. The Ping circuit offers a behavior similar to the BRENSO but AC-coupled. Instead of shooting the frequency to the moon with any trig, CUNSA gently responds to different incoming gates with a selectable decay curve. The Ping circuit can thus create natural decay sounds when fed with trigs or smoother envelopes with any other voltage, like a linear integrator with a custom decay.

Besides this, you can also feed the filter's audio input with trigs and make it ring at high Q settings.

Linked or Individual Filtering

The four filters can work independently or arranged in groups through seminormalled inputs and sum outputs. CUNSA can thus be a 4×1, 2×2, or a massive 1×4 filter. Even odd configurations are possible, like 1+2+1 or 3+1. Mono, stereo, or quadraphonic audio is at your fingertips.

Filter and Combo Behaviour

When the filter behavior is set to COMBINED, every control of the cutoff frequency also affects the input VCA, reducing the signal amplitude and saturation as it approaches the lowest range. It can make organic decays with the ping circuit or tame the low range at high Q and Character settings.

Four Seminormalizations for Group Use

Four inputs have a cascaded seminormalization: audio inputs, VCA CV, V/oct, and Ping. Every signal patched to a filter will thus feed also those at its right, making simultaneous use even simpler. To remove a seminormalization, simply patch a dummy cable to the corresponding input.

Analog Mixing Stage and Group Outputs

Every filter output can be routed to an analogue mix bus that sums the four filters and outputs them in three combinations: all, 1+2, and 3+4. These outputs allow for versatile audio processing. Just like we did with FUMANA, we added a gentle shelving EQ for the higher frequencies of the All output to provide additional timbral variety.

CV Inputs with Attenuators

Besides the seminormalled inputs, every filter features additional CV inputs for cutoff frequency, Q, and Character, each with a dedicated attenuverter.

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Oof. Frap casually serve up one of the best filters we've seen in a long time. Quad multimode circuits with saturation and feedback give you extensive routing options. Delicious.

Supplier's Notes:
cunsa /'cu?nsa/ s.f. [dialect of Modena of uncertain etymology, probably from a Latin *comptiare, derived from comptus, participle of comere 'organize,' 'decorate'] i curing, seasoning (of foods), tanning (of leathers).

Seasoning is crucial for cooking. It is a process that enhances the flavors, glues the ingredients together, and even adds some unexpected kick.

From a gentle refining touch to a shovelful of spice, CUNSA is the perfect seasoning tool for your patches. It can sweeten a sour lead or beef up an insipid bass line, and anything in between.

And, just like a good oil, you can even taste it by itself!

CUNSA is a quadruple analog pingable multimode resonant filter, saturator, mixer, and oscillator.

It is Frap Tools' sound seasoning tool: it can gently even a patch, applying a final touch, or it can set it on fire with a ridiculous amount of spice. It's up to you and your cooking style!

It consists of four multimode resonant filters with a custom saturation and feedback control that you can use independently or in various combinations and roles thanks to a series of seminormalizations.

Four Analogue Resonant Multimode Filters

CUNSA features four state-variable filters that can be used independently or linked and mixed. Each filter provides three behaviors simultaneously: lowpass, bandpass, and highpass. Each behavior has a 12 dB/oct slope, except for the lowpass, which can be either 12 or 24 dB/oct.

Unique 'Character' Circuit for Feedback and Distortion

CUNSA handles feedback and gain staging with extreme control and versatility. Besides the usual Q control that emphasizes the cutoff frequency, the Character circuit defines the amount of soft clipping when the filter overloads. High clipping guarantees a controlled behavior with fat tone and pure resonance, while low or no clipping lets the signal saturate the filter stages and make it scream.

V/oct Tracking and Quadruple Oscillator

Each filter responds to the V/oct signal with excellent tracking. It is thus possible to move the cutoff frequency along with the main melody or make CUNSA resonate with no input and transform it into a multiple oscillator. The V/oct inputs are seminormalled so you can control more filters with the same CV. Easy chords stabs!

Ping and Ring

CUNSA is ideal for percussive and organic tones. The Ping circuit offers a behavior similar to the BRENSO but AC-coupled. Instead of shooting the frequency to the moon with any trig, CUNSA gently responds to different incoming gates with a selectable decay curve. The Ping circuit can thus create natural decay sounds when fed with trigs or smoother envelopes with any other voltage, like a linear integrator with a custom decay.

Besides this, you can also feed the filter's audio input with trigs and make it ring at high Q settings.

Linked or Individual Filtering

The four filters can work independently or arranged in groups through seminormalled inputs and sum outputs. CUNSA can thus be a 4×1, 2×2, or a massive 1×4 filter. Even odd configurations are possible, like 1+2+1 or 3+1. Mono, stereo, or quadraphonic audio is at your fingertips.

Filter and Combo Behaviour

When the filter behavior is set to COMBINED, every control of the cutoff frequency also affects the input VCA, reducing the signal amplitude and saturation as it approaches the lowest range. It can make organic decays with the ping circuit or tame the low range at high Q and Character settings.

Four Seminormalizations for Group Use

Four inputs have a cascaded seminormalization: audio inputs, VCA CV, V/oct, and Ping. Every signal patched to a filter will thus feed also those at its right, making simultaneous use even simpler. To remove a seminormalization, simply patch a dummy cable to the corresponding input.

Analog Mixing Stage and Group Outputs

Every filter output can be routed to an analogue mix bus that sums the four filters and outputs them in three combinations: all, 1+2, and 3+4. These outputs allow for versatile audio processing. Just like we did with FUMANA, we added a gentle shelving EQ for the higher frequencies of the All output to provide additional timbral variety.

CV Inputs with Attenuators

Besides the seminormalled inputs, every filter features additional CV inputs for cutoff frequency, Q, and Character, each with a dedicated attenuverter.

Notes: The Falistri is a fully analogue multi-purpose movement manager designed to generate and edit voltages to easily accomplish any patch.

The module can be divided into two big parts: in the upper two-thirds of the panel take place two specular function generators, while the lower third is composed of a dual cascaded frequency divider, a linear slew limiter, and a four-quadrant multiplier.

Key features:

Two Function Generators: Envelopes, LFOs, Oscillators
Adjust the Shape Without Changing the Time
Exclusive Shapes per Stage
Trig Buttons: Play Those Envelopes!
Three Play Modes (Voltage-Selectable)
Interacting Functions: Quadrature Mode
All the Outputs, Everywhere
Cascaded Frequency Dividers
Four-Quadrant Multiplier
Linear Slew Limiter

Size 18 HP
Depth 38 mm

Current draw
170 mA @ +12 V
170 mA @ -12 V

Notes: The FUMANA is an all analog dual filter bank with various control to access dynamically these bands. Each filter bank is composed of an array of 16 independent 48dB/oct bandpass filters. Having two identical filter arrays, allows you to use one of those for spectral analysis (of a modulator signal) and the other for spectral re-synthesis (of the main signal). Each array is sub-grouped in odd and even bands (numbering these increasingly from 1 to 16 from left to right). It is possible to apply different signal to odd and even bands, both for main and/or modulator arrays. This, together with the 16 envelope followers connected to each band of the modulator filterbank, and the 16 VCA connected to each band of the main filterbank, allows the FUMANA to perform a single 16 bands or a dual 8 bands analog spectral transfer.

While the upper section provide access to each main filter's direct output, the lower section has 4 voltage controllable parameters to manage two independent functions for further spectral editing: tilt and parametric scan.

The tilt, as the name suggest, tilts the spectrum, adding and subtracting amplitude to the 16 bands, emphasizing lower or high bands, and attenuating high or lower bands: this is managed only with the green potentiometer.

The parametric scan, instead, works with three parameters: peak/notch, band selector and width. Like in a parametric equalizer, where is possible to set peak/notch gain, frequency and slope, the FUMANA uses three parameters to set which is the centre band to perform this manipulation, then if that band should be emphasized or attenuated, and how this action is extended to nearby bands.

In addition to the 16 bandpass outputs, there are other 4 outputs provided: the all bands output, the all envelope followers output, the odd bands and the even bands output. These two have the options to be inverted in phase with two switches, in order to obtain even more combination when summed together, maybe/also with the "all bands output", using, for example the 333 module.

Since a spectral transfer tool may be used as a "vocoder-like-effect", the FUMANA provides an input for an external noise which may be used for unvoiced (fricative/sibilants) sounds as words containing or starting with s, f, z, ch and other fricative sounds.

Notes: Designed for Frap's CGM Creative Mixer modules, the Masterone takes an input via IDC socket rather than standard Eurorack connections, then feeds out to headphone outs, balanced stereo XLR, TRS and mono.

Supplier's Notes:
The Masterone is the first Frap Tools module designed to be connected exclusively with non-Eurorack equipment.

It features four separate output sections with different Neutrik connectors and adjustable gain levels to suit the most common live and studio situations (and even some uncommon ones).

With no inputs and just large-format outputs, it pushes even further the concept behind the M module: being a Eurorack system's gateway to the outside world.

XLR Balanced Stereo Outputs

Two XLR connectors (left and right) provide a balanced output with the expected 6 dB extra gain. In many cases, they can allow bypassing a DI box.

TRS Pseudo-Balanced Stereo Outputs

These outputs are very similar in concepts to the ones on the M module, but with large 1/4" jack connectors. It is possible to patch standard TS cables and use them as unbalanced outputs, or use TRS cables to interface them with balanced equipment (the ground is routed to both the ring and the sleeve, for a better performance than regular unbalanced outputs).

Attenuation Switches for Flexible Connectivity

If the two stereo outputs are too hot, a set of switches can attenuate them. The Line/Mic switch on the XLR outputs attenuates them by ~30 dB, while the Line/Inst switch on the TRS outputs attenuates them by ~15 dB.

Stereo Headphones Output with Pre-Fader Listening

The Headphones section allows you to monitor the Master output with an independent volume knob and, at the same time, take advantage of the PFL function on the Channels and the Groups. Rotate the PFL crossfader towards the blue section to blend the PFL modules with the Master sum and check if everything is okay before launching the next scene.

Mono Output with Dedicated Fader

Should you need an extra monitor on stage, or run the whole system through a vintage amp in the studio for parallel processing, the auxiliary monophonic outputs is the answer. It provides the sum of both channels in a handy, pseudo-balanced output with a dedicated fader: attenuate the line level by 15 dB, or amplify it by 6 dB.

12-LED VU Meter with Memory

A detailed VU Meter monitors the signal amplitude from -40 to +15 dB with peak memory on the upper LEDs.

Dimensions:

12HP

38 mm deep

85 mA +12V - 80 mA -12V

with headphones at high level (250O)

110 mA +12V 105 mA -12V

Notes: The SAPEL is a random control voltages source for Eurorack modular systems. It is composed of two main sections, one that generates audio noises, in 4 different versions, and another which includes two specular random clock, random voltages and clock sources.

Noise outputs are colour coded, based on the noise colours, and include:

- Blue (+3dB/oct spectrum)
- White noise (0dB/oct spectrum)
- Pink noise (-3dB/oct spectrum)
- Red noise, a.k.a. Brown or Brownian (-6dB/oct spectrum).

The random voltage and clock section features four uncorrelated random CV generation paths, divided in;

- Fluctuating random voltage;
- Quantized random voltage with 2n stages tuned in semitones referred to 1V/oct scale;
- Quantized random voltage with n+1 stages tuned in octaves referred to 1V/oct scale;
- Non quantized sample & hold.

It is also possible to set a probability distribution with a potentiometer, and apply (or do not apply) the chosen distribution setting to each of the four paths independently.

Furthermore, each of the two random sources section features an independent built-in clock generator, with clock output and random clock output, which can be used in "more than" or "less than" mode. It is possible to use an external clock signal as a clock source, bypassing the built-in one. In addition to that, it is also possible to hand trigger the clock via a manual sample & hold button, which can be also modulated by gate signals.

Notes: The SC (Stereo Channel) is a single-channel stereo module for the CGM Eurorack mixer, fully compatible with every other product of this family.

It features a mono/stereo local output which makes it ideal for multitrack recording and advanced parallel processing.

Thanks to its advanced I/O configuration, it can work as stereo-to-stereo, mono-to-mono, mono-to-stereo, and stereo-to-mono.

The gain control and the two mono FX sends can work in pre or post-fader mode, and the pan pot can also work as a dual mono crossfader, making it suitable for blending two mono sources into a single mono sum.

All the parameters are voltage-controllable for creative mixing automation.

Mechanical mute, PFL, and Solo-in-Place complete the feature set suitable both for studio and live performances.

*The SC replaces the C as the primary single-channel CGM solution. The C module is now discontinued.

Notes: USTA is a 4×4 tracks sequencer for voltages and gates with variable stage duration, designed to quickly see and edit multiple voltage relationships in real time.

Variable stage duration means that every single stage duration can be individually set in relation to the clock, instead of being constrained to a one-to-one ratio (i.e. one stage per every clock impulse).

4×4 tracks means that every stage can store and generate up to four separate voltages (two CVs and two gates), and that up to four independent stage sequences can be arranged into as many different tracks.

Its architecture is based on an array of 16 'Stages' which form a 'Pattern'; 16 patterns form a 'Track', and four tracks form a 'Project'. Within each track, each stage can provide two gates and two CVs, and a wide set of options is available to define and modify the value of each output ('Layers') and the way it is played ('Colours').

Every Stage is related to a dedicated stepped encoder for quick and intuitive editing, and all the 16 encoders are arranged in an oval layout with a circular playhead. Every encoder is surrounded by a ring of 16 LEDs and a RGB led, to provide a visual feedback of the current setting of that step basing on the layer you are working on (like raw CV, quantized CV, length, gate...) and the way it should play depending on the RGB colour.

Notes: Advanced generative sequencer featuring mutes per channel and transposition facilities.

Akropoli is an extension and enhancement of our successful Little Melody and High Towers modules, offering the features of both of these modules as well as some of it's own unique features such as mute buttons per channel, manual transpose knob and 1V/oct transpose CV input. Akropoli operates using Frequency Central's proprietary TOOL V2 code, and can count in integers as well as multiples for even more subtle and evolving variations.

Akropoli is a generative sequencer based around clock divisions and a chromatic quantiser, used to create in-the-moment licks and riffs. It is more that the sum of it's parts.

Akropoli's internal operations can be considered as 4 clock dividers patched into a CV mixer via attenuators. The attenuators select notes over a 5 octave range, the clock dividers determine how often those notes are added to the mix. The final output of Akropoli is quantized chromatically for fast set up and continuously pleasing results. Akropoli has an onboard transposition knob, as well as a 1V/oct transposition CV input.

The 4 clock dividers are labelled A, B, C, and D. They all receive clocks from the same source, the divisions may be selected using the presets and the individual division selectors. The clock dividers can be set to count up, down, or to one of a variety of modes that move between counting up and down. For further information on Presets and Modes see the Little Melody User Guide.

Additionally, each clock divider has it's own binary output (either high or low), these 4 outputs can be used to clock/gate/trigger other stuff on other modules to great effect.

Product Specifications

12V draw
50mA

-12V draw
36mA

5V draw
0mA

Depth
35mm

Notes: A couple of years back, Frequency Central developed Cosmic Background as a standalone percussion voice. The concept was to bundle all required sub-modules behind one panel, pre-patched, yet also fully modular, with each sub-module having its own inputs and outputs. This proved to be a very popular product, but Frequency Central decided to replace Cosmic Background's noise generator with a VCO (and do a few other tweaks), creating a cute little fully modular synth voice ripe for sequencing - and that's how Dark Star was born!

Dark Star consists of 4 sections:

Voltage Controlled Oscillator based on AS3340 with sawtooth, triangle and pulse waveforms
Voltage Controlled Filter with lowpass and highpass options, Drive control, Sweep control which attenuates amount of Release CV
Release generator with CV input for voltage control of release time. Option for sustain via jumper on rear panel.
Voltage Controlled Amplifier
Together they form a pre-patched super versatile analogue synthesiser voice.

Additionally, each section is fully modular in it's own right, so there are patch points for:

1V/oct CV input
PWM CV input - attenuator doubles as manual pulse width when no external signal is present
Gate input for Release or Sustain/Release
Release CV input for voltage control of Release time
VCF audio input with attenuator, for introducing external audio
VCF CV input with attenuator (1V/oct CV is normalised to this input)
VCA audio input (VCF is normalised to this input)
VCA CV input (Release CV is normalised to this input)
Release CV output
VCO audio output
VCF audio output
VCA audio output

Here are some useful patches to try:

Release CV output to PWM CV input, for swept PWM
VCF OUT to VCF IN, thickens and further overdrives the filtering
VCO OUT to VCF CV input, for fizzy FM of the filter
Use a multiple to patch 1V/oct to Release CV input, lower notes will have longer release, higher notes will have shorter release

Product Specifications

12V draw: 28mA
5V draw: 0mA
-12V draw: 28mA

Depth: 35mm
Width: 16HP

Notes: Looking Glass is an 5 x 5 active patchbay/matrix mixer/switcher for both audio and control voltages. It features:

5 inputs (1 through to 5), each with attenuators
5 inverted outputs (A through to E) which are 180o out of phase with the inputs
5 normal outputs (A through to E) which are in phase with the inputs
A switch matrix of 25 push on/push off switches and LED status indicators
Any of the 5 inputs can be patched to any of the 5 outputs simply by pressing the corresponding switches. A patched signal will appear at both normal and inverted outputs simultaneously.

A single input can be patched to a single output. A single input can be patched to multiple outputs. Multiple inputs can be patched to a single output. Multiple inputs can be patched to multiple outputs.

The attenuators allow you to reduce the volume of an incoming signal. If you add many inputs to one output you will of course cause clipping (which may or may not be desirable!), the attenuators are your on-board way around this.

Specifications:

12V draw: 30mA
5V draw: 0mA
-12V draw: 31mA
Depth: 35mm
Width: 18HP

Notes: Shapes is a wide ranging and fully analogue oscillator which can perform duties as both auxilliary VCO* as well as VC-LFO. Shapes can be configured to cycle continuously, or to provide one-shot shaped outputs. When set to one-shot mode, Shapes may be used as an ersatz envelope generator.

Using the Time knob, Shapes can cycle from as low as 8 seconds (whale song) to as high as 19500Hz (bat beeps).

Shapes has 3 simultaneous outputs:

sawtooth (+/-5V, 10Vpp)
ramp (+/-5V, 10Vpp)
triangle (+/-5V, 10Vpp)
Additional waveforms may be derived courtesy of the Shape knob. Anticlockwise from 0 achieves progressively logarithmic sawtooths and ramps, whereas clockwise from 0 achieves progressively exponential sawtooths and ramps. The effect of the Shape knob on the triangle waveform is asymmetric, anticlockwise from 0 achieves progressively logarithmic leading edge, whereas clockwise from 0 achieves progressively exponential falling edge. Progressively exponential triangle waveforms can be achieved using the Time CV knob (set Shape knob to 0) providing there is no jack in the Time CV input socket

Time CV input provides wide ranging control of time. It is possible to dial in something approaching 1V/oct over a limited range, although Shapes has not been designed to perform as an accurately tracking VCO. In the audio range, Shapes comes into its own when used as a 'daughter' VCO to an external 'mother' VCO by patching the 'mother' VCO into Shapes' Gate In input socket - some impressive oscillator sync style effects can be achieved.

Gate In can also be used to initiate waveforms in one-shot mode, where a pulse of any length will cause Shapes to complete one cycle.

*Shapes has not been designed to perform as an accurately tracking audio VCO.

Product Specifications

12V draw: 15mA
5V draw: 0mA
-12V draw: 15mA
Depth: 45mm
Width: 4HP

Notes: Expandable 4 channel VCA based stereo mixer with tone shaping and FX bus.

Chipset:

For this item, Frequency Central offer a CHIPSET which contains the following:

3 x LM13700

For all other components required, please see the build document.

Features:

4 x input channels, each featuring LEVEL, HIGH, LOW, FX send, PAN, MUTE and CV control of level.
FX send and stereo return + FX phase jumper
Left and Right Eurorack level inputs (2 x 3.5mm sockets)
Left and Right line level outputs (2 x 6.35mm sockets)
Scribble strips!

Strips is also expandable! You can add a second strips, connected to the first via a 16 pin to 16 pin cable. The cable powers the second Strips and gives you 8 channels to play with. The second Strips accesses the first Strips FX bus. When using in expanded configuration, the FX send/return and main outputs for the second Strips are not available. Here's how!

FX phase jumper - because not all FX that you might use in the FX loop are in phase with respect to their input/output. The phase jumper allows you to compensate for this and avoid weird phase cancellations.

Product Specifications

12V draw: - 43mA
5V draw: - 0mA
-12V draw: 43mA
Depth: 39mm

Notes: Wonderland is an 8×8 active patchbay/matrix mixer/switcher for both audio and control voltages. It features:

8 inputs (1 through to 8), each with micro-attenuators (which can be set with a small screwdriver)
8 buffered inverted outputs (A through to H) which are 180o out of phase with the inputs
8 buffered normal outputs (A through to H) which are in phase with the inputs
A switch matrix of 64 push on/push off switches
Any of the 8 inputs can be patched to any of the 8 outputs simply by pressing the corresponding switches. A patched signal will appear at both normal and inverted outputs simultaneously.

A single input can be patched to a single output. A single input can be patched to multiple outputs. Multiple inputs can be patched to a single output. Multiple inputs can be patched to multiple outputs.

Each input features a micro-attenuator which can be set with a small screwdriver. This space saving feature allows you to reduce the volume of an incoming signal without having to resort to external attenuators. If you add many inputs to one output you will of course cause clipping (which may or may not be desirable!), the micro-attenuators are your on-board way around this. I find it useful to leave the micro-attenuators set to 50% (which is how they come pre-set at delivery). Of course, their size is a little bit of a compromise, but they are a useful feature nonetheless. Wonderland’s sister module Looking Glass includes full size input attenuators as well as LED status indicators.

Product Specifications
12V draw
30mA

5V draw
0mA

-12V draw
31mA

Depth
35mm

Width
18HP

Notes: Clouds, the granular synthesis module from Mutable Instruments, was discontinued in 2017. Supercell brings back Clouds in a more accessible 34 hp form factor, offering an improved user interface and several additional features:

- Each of the Blend parameters (Feedback, Panning, Mix, and Space) have dedicated knobs with their own CV inputs and inverting attenuators (attenuverters).

- The inputs and outputs now have mute switches, stereo VCAs, and separate VU meters. The knobs act as offset controls when their respective VCA inputs are patched.

- A stereo output gain control has been added, providing an additional +6 dB of gain to compensate for low output levels when using certain parameter combinations.

- The complex process of changing the sampling time and managing presets has been simplified with dedicated switches and status LEDs.

- Extensive modulation options for all parameters including direct patching of external CV, distribution of one CV to all parameters via the AUX input, or an internal smooth random CV that is normalized to any unpatched inputs when AUX is also unpatched. The attenuverters control the modulation depth in all three cases. As of firmware v1.01 the internal modulation rate can be adjusted within a range of 1 to 100 Hz.

- The inputs and outputs now include stereo VCAs and separate VU meters. The knobs act as offset controls when their respective VCA inputs are patched.

- Pitch is now controlled by two separate inputs: the V/Oct input is exponential and the Pitch input is linear. When both inputs are used, their voltages are summed.

- A manual Trig switch (for capturing individual grains) has been added, in addition to the Trig input that was present on Clouds.

All other features of the original Clouds remain intact, including access to the alternate modes. Thanks to Olivier Gillet for making the original Clouds hardware and firmware available under open-source licenses. Third-party firmware such as Parasites (by Matthias Puech) and Beat Repeat (by Julius Kammerl) will be supported in future firmware updates after the initial release of the module.

Notes: A full-on digital modular system in a single module. Eight-voice polyphony, audio processing and CV/MIDI functionality, all customisable via the PC/Mac editor. Serious DSP power in 22 hp.

Supplier's Notes:
Integrate the power of EaganMatrix Sound Technology into your Eurorack! The EaganMatrix Module is a full-featured EaganMatrix Sound Engine for Eurorack, and can be controlled by control voltages and/or Midi. This versatile module can act as a sound source, a sound processor, a CV source (via connection to an external Control Voltage Converter), a Midi source, or a customizable combination of all these capabilities.

The EaganMatrix Module provides a truly versatile framework for both studio and live performance. Flexibility is key, due to its audio inputs and outputs, integrated CV inputs, external CV outputs (via Control Voltage Converter), and robust implementation of MPE and MPE+ Midi.

A single EaganMatrix Preset can give completely different sonic results, depending on how it is patched into a particular Eurorack ecosystem. Hundreds of System Presets are included with the EaganMatrix Module. In addition, an external cross-platform (Mac and PC) Haken Editor may be connected to modify and customize the supplied EaganMatrix System Presets, or create completely new presets from scratch.

The EaganMatrix Sound Technology, originally created for the gesturally highly sensitive Continuum, is now available to you in a Eurorack module. The EaganMatrix Module will quickly become a 'goto' component in your modular sound design and sonic composition.

Haken Audio's EaganMatrix Module offers:
Polyphony: Nominal 1, Maximum 8
Direct CV note control is limited to 1 voice at a time, but higher polyphony avoids voice stealing when EaganMatrix presets have long decays, and higher polyphony is often useful for Midi input.
4 Per-note CV Inputs: W, X, Y, Z
Gate (W) - Triggers at 1V, with max range -10V to +10V
Pitch (X) - 1V per octave, with programmable offset for Middle C; useful input voltages are a subpart of -10V to +10V (depends on the programmable offset selected)
Timbre (Y) - Function depends on EaganMatrix preset; voltage range is normally 0V to 5V, but -5V to +5V can be useful when combined with a programmable offset
Loudness (Z) - normally 0V to 5V, but -5V to +5V can be useful when combined with a programmable offset
4 Global CV Inputs: i, ii, iii, iv

Functionality depends on EaganMatrix preset; these CV affect all voices (notes from WXYZ and Midi); each global CV is normally 0V to 5V, but -5V to +5V can be useful when combined with a programmable offset
2 Analog Audio Inputs: Left and Right, or Mono
2 Analog Audio Outputs: Left and Right, or Mono Sum
-12dB switch selects between Eurorack Level and Line Level
Midi over USB
Allows bidirectional MPE and MPE+ connection to other devices; allows connection to the Haken Editor for editing and archiving EaganMatrix presets (USB-A cable included with purchase)
Universal 3.5mm Midi In (Type A, Type B, and TS)
Allows connection to other Midi devices without need of computer or USB (adapter to 5-pin DIN Midi In included with purchase)
Type B 3.5mm Midi Out
Allows connection to other Midi devices without need of computer or USB (adapter to 5-pin DIN Midi Out included with purchase)
i2c Port for Communication to the Control Voltage Converter
(a switch selects between 3.5mm Midi Out and i2c functionality)
12 Switches, 1 Rotary, and LED Matrix

A menu system allows stand-alone operation without need of computer, and provides monitoring for notes being played and CV input levels
The EaganMatrix is a modular digital synthesizer invented by Edmund Eagan, utilizing a DSP engine designed by Lippold Haken. This is the same EaganMatrix Sound Technology internal to the Continuum Fingerboard, the ContinuuMini, and Expressive E's Osmose keyboard. The EaganMatrix allows the user to finely craft their musical sound by digitally connecting audio and control modules via a patching matrix. The EaganMatrix Module contains a sophisticated digital modular patching world of its own, ready to interact with your other Eurorack modules to make musical results never before possible.

Power and size

The EaganMatrix Module requires +12V, +5V, ground, and -12V from your Eurorack enclosure.

A 16-pin standard Eurorack power cable is included with purchase.

Current requirements: 25mA at +12V and -12V. 300 mA max (190 mA avg) at +5V.

The processing power of the EaganMatrix Module is 2x, same as the ContinuuMini.

The EaganMatrix Module dimensions are 22 HP and 3cm depth.

Notes: 2xSAM is 4 HP Dual Stereo Attenuator-Mixer

Several 2xSAMs can be chained together or with other HN stereo modules via sockets on the back side.

2xSAM's total mix stereo output can be internally sent to the Isolator, PanMix Jr, 3xStereo Mixer, or can be received from OUT, PanMix, PanMix Jr, 3xStereo Mixer, or another 2xSAM.

If jumpers are not installed (placed on one pin only by default) the max gain is 1x. When the jumper is properly placed on both pins - the gain is 5x. There are four inputs thus four jumpers. Each jumper is relevant to its channel.

27 mA +12V
27 mA - 12V
35 mm Depth
4 HP wide

Notes: 3xMIA is a 6-channel attenuverting mixer/offset/scale/polarizer

3 blocks of 2-channel attenuverting mixers, using dual concentric pots. Each channel can be switched to mix with the subsequent channel, allowing for 2-2-2, 4-2, 6 mix configurations.

With nothing plugged into an input, an offset is normalled to that channel. The inner knobs control the A inputs, while the outer knobs control the B inputs.

DC coupled, so it can be used for audio, CV, or both at the same time.

80 mA +12V
80 mA -12V
35 mm Depth
24HP wide