安全なお買い物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全なお買い物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Steady State Fate Entity Bass Drum Synthesizer Module

$340.03

SAME DAY SHIPPING!
ParcelForce, FedEx, Royal Mail
安全なお買い物
 2 in stock
 Add to Wishlist
Order by phone
+44 20 7424 1960
quote 658624
Lines open in 11 hrs 22 mins.
Details
Features
Specs
Manual/brochure
Delivery
Returns

The Entity Bass Drum is a complete and versatile synthesizer voice geared for designing a huge array of bass drum, percussive and synth sounds. Finally, a truly deep tool for creating analog bass drum, bass lines and other percussive effects is here!

The design consists of a high fidelity resonant filter, 2 stage slope generator (rise/fall) with independent slope shaping, a high fidelity VCA and discrete transistor saturation circuitry. Every parameter on the Entity Bass drum is voltage controllable.

By applying a trigger of any length and at least 2V amplitude, we excite the resonant filter to produce a percussive sine wave. The pitch control tunes the output with a range of 8Hz to around 2.2KHz. Both higher and lower levels are achievable using the FM input for modulation etc. The internal filter will track 3-4 octaves reliably and the tracking device is temperature compensated.

The slope generator (ENV) can be switched into the circuit via the 3 way switch below the FM LVL control. This control is a bipolar attenuator which affects the level of the slope generator and/or external modulator that affects the pitch of the output.
The 3 way switch selects FM, FM+ENV or just ENV as a mod source.

The rise/fall envelope is a two stage function generator. The controls provide slope timing from 1ms to about a minute. To the right of these controls is the shaping section where logarithmic, linear and exponential slope shapes are selected independently for the two envelope stages.

The envelope is designed to re-trigger at a set point. This allows for changing dynamics to occur to pitch and amplitude when the slope times are greater than the output transient time. For instance the sound can vary between any number of triggers that fire before the envelope set point is reached. Setting the slope time fast enough (below roughly 1 o'clock) provides for nominal operation. Settings will vary depending on trigger and ring decay timing.

The envelope can also be used exclusively or in a more complex patch via a direct +ENV output. Additionally, a novel DUCK output provides a means to control external VCAs - to work like slow compressors. DUCK is an inverted and positively offset version of the +ENV out. This keeps VCAs open when the envelope is off and effectively 'ducks' the VCA when the envelope fires. Of course, mod sources for these outputs are not limited to VCAs...

BODY is a subtle, yet novel control. This control simulates the tightness of a drum head. All the way tight, we get a softer and somewhat muted sound, to the right we achieve a more flabby sound. The middle region is the sweet spot for a nearly perfect resonant drum. BODY can have a greater effect depending on the other parameters and can be very useful for fine tuning the sound in a mix and designing original drum sounds.

RING controls the resonant decay time. Both short and plucky and an infinite ring are obtainable. The filter is tuned so that it will always resonate a little, even when RING control is all the way down.

Before the output section, we have the discrete transistor saturation. We like this because of the vintage low end distortion from overdriven class-A discrete amplifiers. This one is tuned a bit more aggressively and just a touch is necessary to add some bite. However, you can go over the top and get brutal if you so desire... ;-)
The saturator will overdrive the output stage for more of a hard clipping effect that can be tuned out by adjusting the output level control without sacrificing signal amplitude - its a hot signal by intention.

The OUTPUT section is a parallel signal processor design. The OUTPUT control blends the nominal output with a secondary input (or nothing) depending on the 2 way switch setting below the control and/or whether an external signal is patched into the AMP CV input. In 'AMP' mode, the OUTPUT control works like a volume control. If a signal is active on the AMP CV input, the control will blend between the nominal output and the CV control level. Similarly, in 'ENV' mode we get the same blending action using the internal envelope.

The VCA can also be accessed directly via the A-MIX input. This allows you to use the output section as a standalone VCA (modulated via the envelope or not) or to mix other sounds with the Entity. Feedback patching is a possibility using a stackable or mult to feed the output into the A-MIX input. This produces a juicy distortion effect of a different flavour, you may like it.

The filter can be used independently or in combination with the nominal output via the F-MIX input. This input is used as an aux trigger input that is sensitive to pulse/trigger width. As the effect is less dramatic than the main trigger, dynamic rhythms are achievable using both inputs and creative triggering.

  • Inputs: Trigger, Body CV, FM CV, Saturation CV, Amp CV, Rise CV, Fall CV, Ring CV, 1V/oct, A-Mix, F-Mix
  • Outputs: +Env, Duck, Audio output
  • PING! button to demo sounds without a trigger source
  • RGB LED for visual feedback of trigger, FM and output waveform
  • All parameters are CV controllable. Controls double as CV attenuators
  • Very high fidelity design
Module Type Bass Drum Module
Dimensions (mm) 70 x 40 x 128
Weight (g) 157

If you decide an equipment item is not suitable within 10 days of delivery, you can return it to us for a replacement or refund. Returns must be unused and in their original, undamaged packaging.

Gifts purchased between 30 November and 24 December may be returned by Friday 6 January 2016”.

Some items are excluded from our money back guarantee, including:
• Computer software that has been unsealed or registered
• Any item that comes directly into contact with the nose, ears or mouth

To arrange a return, just contact our customer service department on 020 7424 2800 or email us at support@juno.co.uk

View our full range of synth modules

BEST MUSIC STORE: 5 TIME WINNERS