Erica Synths

Notes: You may wonder - what's that strange connector on the top of the Bullfrog? This is the VOICECARD slot. Voicecards expand functionality of the Bullfrog and make it even more versatile. Essentially, the voicecards replace patch cables - they connect the "modules" of the Bullfrog internally. But that's not all about them - some voicecards have built in mixers, signal generators and advanced electrical circuits to control the synthesiser, for example, sequencer that sends CV to control pitch and gate to start events on the synthesiser.

When inserting voicecards, make sure, the front panel of the voicecard faces the main interface of the Bullfrog. It is recommend that you turn off the Bullfrog when inserting a new voicecard.

The ELECTRIC ORGAN voicecard makes internal connections of the Bullfrog to emulate pipe organ, when several notes are played together. It also illustrates the principles of ADDITIVE SYNTHESIS. In additive synthesis several simpler waveforms are mixed together to generate more complex sounds. On this voicecard the pulsewave is sent to the DIVIDER and all outputs of the divider are mixed together with the original pulsewave and sent to the VCF and then to the VCA. Both ENVELOPE GENERATORS are involved in the same way as on the Acid Bassline voicecard. The DIVIDER divides an original frequency by even numbers and as result produces a pitch that is even octaves down form the original pitch. Faders on the voicecard determine an amplitude of each suboctave. Set the VCA OFFSET all way counter clockwise, PULSE OUT to the max. Push the MANUAL GATE button to check the sound. Tweak settings of the faders and observe the difference in the sound. Tweak CUTOFF and RESONANCE knobs. Add some echo by setting the DRY/WET knob to 12:00 and find the best DELAY TIME and FEEDBACK settings. Now, connect the keyboard and you are ready to perform Toccata and Fugue in D minor.

Notes: You may wonder - what's that strange connector on the top of the Bullfrog? This is the VOICECARD slot. Voicecards expand functionality of the Bullfrog and make it even more versatile. Essentially, the voicecards replace patch cables - they connect the "modules" of the Bullfrog internally. But that's not all about them - some voicecards have built in mixers, signal generators and advanced electrical circuits to control the synthesiser, for example, sequencer that sends CV to control pitch and gate to start events on the synthesizer (Figure 40).

When inserting voicecards, make sure, the front panel of the voicecard faces the main interface of the Bullfrog. It is recommended that you turn off the Bullfrog when inserting a new voicecard.

As it's name suggests, the HIGHPASS VCF voicecard expands the sound treatment capabilities of the Bullfrog by bringing a highpass filter into the game. This allows for exploring highpass and bandpass filtering. The voice card features typical VCF controls - CUTOFF frequency, RESONANCE and CV LEVEL. The CV source switch allows for selecting between three CV sources - envelope generator 2, Sample & Hold LFO, which is a pulsewave generator in the Sample&Hold "module". The voice card features internal audio connections - the output from the MIXER is patched into the highpass VCF, the output of the highpass VCF goes into the input of the onboard lowpass VCF which is then connected to the VCA. For more flexibility, no CV connections for the Bullfrog are present on the voice card, so you have to do the patching yourself.

Notes: The Erica Synths Black Stereo Delay is a hi-fi stereo delay with a lot of unique features based on our custom DSP engine. Tape, BBD and digital delay emulations with three modes, each accompanied with delay time, feedback, feedback tone and stereo spread controls allow for designing extremely delicate effects. CV control over various parameters and the ability to save up to 10 presets will make this module an integral part of any performance rack. Delay effects are developed by Dutch company www.112db.com

Features

Tape, BBD and digital delay types
Three modes for each type
Tap and clock synchronization of delay time
10 preset patches
CV control over delay time, feedback, tone, dry/wet mix and preset selection
Adjustable stereo delay spread
The modules run on new Erica Synths DSP hardware and the effects are developed in collaboration with Dutch company 112.dB who make some of the most beautiful sounding effects.

Erica Black Series include high-end, unique functionality and superior quality modules. Only the best, highest-quality components are used, all inputs and outputs are protected against undesired overvoltage. Erica Black Series consist of range of modules that are needed to put together entire synth.

Technical specifications:

Max audio input level before clipping: 16Vptp
CV input range (full span): -5V - +5V
Sampling frequency: 48kHz, 24bit
Delay time: 3..3000ms
Audio codecs: -108 dynamic range, -98dB THD+N
Power consumption: 120mA@+12V, 39mA@-12V
Module width: 12HP
Module depth: 35mm

Notes: The Erica Synths Black Reverb is a versatile hi-fi stereo FX module with lots of unique features based on Erica Synths' custom DSP engine. The reverb sources are selectable Tape, BBD and "dirty BBD" digital; emulations with three modes, each - Room, Hall and Cathedral. Delicate room size control, feedback, feedback tone and stereo spin controls allow for designing extremely delicate reverberation effects. CV control over various parameters and the ability to save up to 10 presets will make this module an integral part of any performance rack.

Features:

Reverb based on Tape, BBD and digital delay lines
Three room sizes
Manual and triggered FREEZE with 1V/oct tracking
10 preset patches
CV control over size, feedback, tone, dry/wet mix and preset selection
Adjustable stereo spin

Specs:

Max audio input level before clipping 16Vptp
CV input range (full span) -5V - +5V
Sampling frequency 48kHz, 24bit
Audio codecs -108 dynamic range, -98dB THD+N
Power consumption 120mA@+12V, 39mA@-12V
Module width 12HP
Module depth 35mm

Notes: Stereo version of Erica's DJ-style filter module designed with drums in mind. Simple three-knob interface gives control over joint low-pass/high-pass resonant filter with CV input.

Supplier's Notes:
As its name suggests, the Erica Synths DJ VCF STEREO module provides sound treatment functionality typically found on DJ decks - it is fully open when the cutoff knob is at 12:00. When turned counter-clockwise, lowpass filtering is applied and when turned clockwise, highpass filtering is initiated. Additionally, there is a nice-sounding, adjustable resonance parameter. This provides hands-on control over the sound during performances as well as unconventional timbre modulations that are hard to achieve with conventional state variable filters.

Features

Fully analogue stereo DJ-style VCF
Manual cutoff and resonance control
Two cutoff CV inputs, one with an attenuverter
Technical specifications:

Audio level: 10Vptp
CV level: -10V - +10V
Filter slope: 24dB/oct
Power consumption: +109mA, -101mA
Module width: 8HP
Module depth: 35mm

Notes: ***B-STOCK: Box opened, product in perfect working order***


Erica Synths Modulator is an advanced modulation and pitched noise source with focus on rhythmic (but not limited to) compositions in mind. It features two identical syncable to the BPM LFOs/noise sources with selectable morphing waveshapes. LFO frequency can be manually adjustable, as well as they provide frequency divisions and multiplication in Sync mode. Each LFO has two outputs- main one and secondary one with adjustable phase, so you can create evolving modulations. Furthermore, LFOs can be linked to work at the same frequency and the first LFO has built in VCA to control output signal amplitude.

Notes: ***B-STOCK: Box opened, light surface marks, product in perfect working condition ***


Inspired by Roland's TR-x0x sequencers, the Drum Sequencer brings that classic approach to Eurorack, offering a massive 16 trigger channels with gate and accent outputs, plus a CV/gate track for synths.

Supplier's notes:
X0X-style beat creation for modular systems - Erica's drum sequencer is based on the concepts of classic Roland TR rhythm composers. The module offers 16 trigger channels, twelve of which also feature accent outputs. Additionally, there is a CV and a gate track, meaning you can also notate a bass line or melody. The maximum pattern length is 64 steps. Extensive playback and random functions plus two LFOs help you with creating lively results. Large buttons provide a fantastic feel while programming patterns.

Notes: ***B-STOCK: Without original box, product in perfect working order***


Pico BBD is surprisingly great sounding (we were surprised ourselves), full analogue 4092 stage bucket brigade delay module; the smallest BBD in Eurorack. Besides nice and clean flanger and delay effects, at full CW settings of TIME and feedback knobs it can produce extreme sonic artefacts. Tweak knobs and enjoy!