安全なお買い物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全なお買い物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Synth modules

View:
Options
150/199(ページ1/4)の商品
1  2  3  4  »
Subscribe to our weekly Studio Equipment emails
Cat: 553610 Rel: 19 Nov 14
 
Attenuation inversion & offset adjustment synth module
Notes: In our projet Orage Magnetique dedicated to the design of a sound spaciolab to recreate sounds from space, the module POLES enables to adapt the signal from magnetic polarisation to get the best sound simulation with dual amplification, attenuation, inversion and offset adjustment.

The module POLES offers 2 separate channels.

POLES enables to attenuate, invert & amplify a signal. It is very useful to adapt different signals to different inputs. It also enables to adjust the offset of your signal if you want to adapt it to +/- 5V or 0/+5 for example. If nothing is connected to the input, it will act as a fixed voltage source.
Read more
 1 in stock $56.26
Cat: 553616 Rel: 19 Nov 14
 
Audio mixer synth module
Notes: Very small 6 to 1 input audio mixer with linear Pots
Read more
 1 in stock $74.65
Cat: 553623 Rel: 19 Nov 14
 
Discrete oscillator synth module
Notes: TITAN modules are elements from the Titan Capsule. They are sound generators built to recreate the sound of Titan haze. These transistors made oscillators have a wide range and a very particular sound. 2 TITAN modules will create deep and vibrant basses.

With the knob « densite des brumes », the sound will be shaped through Titan's haze from deep basses to high pitches. The titan transistors generate a very particular sound with a base frequency of +/-15 semi-tones from 1Hz a 6kHz.

Switch -2>0 : multiplies the density of the haze by -2. This will have a direct impact on the sound and make it 2 octaves lower.

Mod2 0>10 is the amount of frequency modulation of mod2 input
Read more
 1 in stock $94.13
Cat: 563563 Rel: 10 Mar 15
 
Buffered multiple synth module, 2HP wide
Notes: Dual 1 x 3 buffered mult (one audio or cv signal in with multiple buffered outputs).

The output of the first mult is normalled to the input of the second mult to create a 1×6 buffered mult
Read more
 More than 10 in stock $69.79
Cat: 569587 Rel: 10 Apr 15
 
Dual Bernoulli gate synth module, 6HP size
Notes: A Bernoulli gate takes a logic signal (trigger or gate) as an input, and routes it to either of its two outputs according to a random coin toss. The knob controls how fair the coin toss is - with the knob in minimal position, the first output always win, with the knob in maximal position the second output always wins - with random fun in-between. And obviously, this bias is CV-controllable!

Branches packs two such gates in a small 6-HP panel. Get a sequencer to randomly skip steps, randomize drum patterns, dispatch events from a sequence to two subpatches, or patch a monster modular Pachinko machine...

Input specifications: 100k impedance, 0.6V threshold.
Output specifications: 5V HIGH level.
Response time: 15us.
6-HP.
Current consumption: +12V: 10mA, -12V: 1mA.
Read more
 2 in stock $95.21
Cat: 569591 Rel: 10 Apr 15
 
Multiples and mixing utilities synth module, 4HP size
Notes: Links provides 3 utility functions focused on signal distribution and mixing.

1:3 is a 3-output buffered multiple, with an offset error < 0.1%. It is useful for distributing the voltage from a CV output with a large protection resistor to several modules - particularly VCOs.

2:2 is a 2-input summer with unity gains. The sum of the two input channels is distributed to 2 outputs.

3:1 is a 3-input mixer with a gain of 1/3 for each channel (averager). It is particularly suitable for rapidly mixing audio sources such as oscillators, for which a unity gain mixer would have caused clipping.

A 2-color output monitoring LED is available for each of these functions.
Read more
 5 in stock $58.42
Cat: 569592 Rel: 10 Apr 15
 
Mixer, offset, attenuverter synth module with 3 channels of audio/CV processing, 6HP size
Notes: Shades provides 3 channels of audio/CV processing which can be configured either as active attenuators or as attenuverters.

A bicolor LED monitors the polarity and intensity of the audio or CV signal on each output.

Unconnected inputs are normalized to an internal precision voltage reference, which can produce either a +5V or +10V constant voltage.

Normalization on the outputs allows the module to be used as a mixer or offset generator: when no jack is inserted in an output, the signal from this output is summed into the next output. Combined with the internal voltage reference, this allows the module to be used as a CV offset control.

Patch examples:

Mixing:
When output 1 is left unconnected, the signal on output 2 is the sum of channels 1 and 2. Channel 3 can be used for another purpose (attenuation, attenuversion, or constant CV generation).

When output 1 and 2 are left unconnected, the signal on output 3 is the sum of channels 1, 2 and 3.

Offset generation:
Leave channel 1's input and output unconnected, and connect a CV source to channel 2's input. Channel 2's output will contain a scaled and offset copy of the input CV. Channel 1's level knob will control the offset and channel 2's level knob will control the signal scale and polarity.
Read more
 1 in stock $89.80
Cat: 580271 Rel: 03 Aug 15
 
Invert offset synth module for modifying control voltages for other modules
Notes: The 6 HP Invert Offset module creates an easy way to modify control voltages for other modules in your system.

The Invert Offset consists of two identical channels. Signal applied to the In jack is vertically offset by the knob, additionally a CV signal may be applied to offset the signal vertically.

The +Out jack puts out a non-inverted signal with the specified offset. The -Out jack puts out an inverted signal with the same offset as the +Out.

The Offset CV input allows you to mix two signals together, Offset will never be inverted, while the signal at the In jack will be inverted based on the selected output.

There is also a sum output (1+2) that takes the non-inverted outputs and adds them together. Also there is a comparator gate output that is on if the channel 1 output is more positive than channel 2.
Read more
 1 in stock $89.80
Cat: 588813 Rel: 02 Oct 15
 
Passive quad attenuator synthesiser module - 4HP wide
Notes: QUAD ATTEN is a passive quad attenuator in a small 4hp profile.

Although quite basic, attenuators are extremely powerful in a modular system.

They are especially useful for adjusting the depth of control voltages going into modules that lack CV attenuators.

Power Draw: +0mA, -0mA (Passive). 6HP width. 25mm Depth.
Read more
 5 in stock $67.08
Cat: 588622 Rel: 09 Nov 15
 
Quad trigger to solenoid motor driver synthesiser module - 5HP wide
Notes: SOLENOID can drive 4 solenoid motors with voltage directly from the power supply. Motor driving circuitry and CV input circuitry are optically isolated without any ground connection. Requires external power supply for driving motors.

Output pulse width a knob optimizes the trigger signals to be sufficient to deliver adequate signal for the solenoids. With shorter pulses, solenoids don't move in their full range, or move with less power. This can also be used for adjusting the dynamics.
Read more
 1 in stock $96.31
Cat: 589492 Rel: 09 Dec 15
 
Buffered multiple synthesiser module with LED indicators - 3HP wide
Notes: The Buff Mult is a buffered multiple with LED indicators to show positive and negative voltages. Using wide bandwidth opamps, it functions as a dual 1-to-3 or a single 1-to-6 mult for audio, video, or CV signals.
Read more
 1 in stock $73.58
Cat: 602205 Rel: 04 Apr 16
 
Quad attenuator, attenuverter, mixer and DC voltage source - 28HP wide
Notes: The shorter and wider brother to the popular Triatt module!

The four handy knobs can act as active attenuators (unipolar) or attenuverters (bipolar) depending on the setting of the two-position switches above each one.

Each input is normalled to a precision +5V DC voltage source. With nothing plugged into the jacks, each knob controls a voltage range of 0 to +5 v or -5 to +5 v depending on the position of the mode switch.

- 2 modes for each channel
- 5v normalled to each input
- With external signals it acts as active/buffered attenuator/attenuverter/mixer
- Each output normalled to mix into the adjacent channel on the right making it possible to do sub mixes in groups of 2, 3 or all four channels.
Read more
 9 in stock $73.58
Cat: 584253 Rel: 15 Apr 16
 
Compact utility synthesiser module for interfacing guitar effects with eurorack modular system - 4HP wide
Notes: The 'S.B.G' is a compact utility module intended for the interfacing of guitar effect pedals with your eurorack modular system.

It provides both attenuation and amplification of audio signals for level matching together with a crossfade control to conveniently adjust the wet/dry mix of a processed signal. The module also offers regulation of outgoing CV signals for safer use of pedal expression inputs.

Technical Specifications:

Supply: +/-12V (Reverse voltage protection)
Current Draw: ~30ma
Size: 4 HP
Depth: 22mm (including power header)
Read more
 1 in stock $94.13
Cat: 584260 Rel: 15 Apr 16
 
Dual channel attenuverter synthesiser module - 4HP wide
Notes: 'O/A/x2' is a dual channel attenuverter with each channel also including a bipolar voltage offset and LED monitoring. The module is primarily intended for fine grain flexible 'editing' of control signals (i.e changing the phase, level and DC offset of an LFO signal) but also has uses with audio signals such as attenuation, inversion and mixing.

Technical Specifications:

Supply: +/-12V (Reverse voltage protection)
Current Draw: ~50ma
Size: 4 HP
Depth: 32mm (including power header)
Read more
 3 in stock $78.98
Cat: 584257 Rel: 15 Apr 16
 
Envelope generator synthesiser module - 4HP wide
Notes: 'Pip Slope' is an envelope generator. It supports both Attack/Decay and Attack/Sustain/Decay type functions with both direct and voltage control of Attack and Decay times. Envelopes can be automatically looped and the function curve type changed between exponential and linear.

Technical Specifications:

Supply: +/-12V (Reverse voltage protection)
Current Draw: ~50ma
Size: 4 HP
Depth: 32mm (including power header)
Read more
 4 in stock $95.21
Cat: 749156 Rel: 15 Apr 16
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


The 'S.B.G' is a compact utility module intended for the interfacing of guitar effect pedals with your eurorack modular system.

It provides both attenuation and amplification of audio signals for level matching together with a crossfade control to conveniently adjust the wet/dry mix of a processed signal. The module also offers regulation of outgoing CV signals for safer use of pedal expression inputs.

Technical Specifications:

Supply: +/-12V (Reverse voltage protection)
Current Draw: ~30ma
Size: 4 HP
Depth: 22mm (including power header)
Read more
 1 in stock $88.00
Cat: 614853 Rel: 06 Jun 16
 
4 channel mixer eurorack synth module - 4HP wide
Notes: The MX1 mixer module from FSS is designed to present a compact, affordable mixing solution for Eurorack users. The MX1 gives four audio inputs in as many HP, with both normal and phase-inverted outputs available.

The level controls of the MX1 are logarithmic, but the channels are DC coupled, so CVs can be summed together using the MX1 if necessary.

The MX1 provides unity gain of each channel when the level control is fully clockwise, meaning that there is no loss of signal level when mixing. This also allows for the MX1 to be overdriven, especially if the same source is multipled to the four inputs or the "normal" output is fed back into one of the inputs.

A set of expansion headers also allow for the FSS P.O.C.A. VAC1 and Whitehall SW1 modules to be used alongside the MX1 without any patching required, when using the MX1x expander accessory.
Read more
 1 in stock $68.16
Cat: 614138 Rel: 16 Jun 16
 
Eurorack envelope synth module based on Roland System 100M envelope - 4HP wide
Notes: The second module in the Roland System 100M clone series, the System X Envelope on 4HP. Includes the addition of a range switch for fast/slow response. Even snappier than a crocodile sandwich.

For audio demo, please visit - http://www.frequencycentral.co.uk/wp-content/uploads/2012/11/MoroderClarke.mp3
Read more
$108.20 SAVE 10%
 6 in stock $97.38
Cat: 614710 Rel: 20 Jun 16
 
Power supply eurorack synth module with 12V & 5V rails - 5HP wide
Notes: The Source D'Energie is a power supply module designed to power up to a 6U case with +/-12v and 5v rails. Wall wart plugs can be used for a skiff or case with few modules, but for anything more than that we recommend a 4A power supply such as this. The Source D'Energie has two 16 pin headers, perfect for powering two rows of your system. LED's on the panel indicate the health of each rail at a glance

Tech Specs
- 5hp Eurorack
- 13.5-15 VDC Input
- +12 @ 1.5A / -12 @ 1.5A / 5v @ 500ma
Read more
 2 in stock $82.23
Cat: 616113 Rel: 07 Jul 16
 
Buffered mult synth module with 2 sets of 3 outputs - 2HP wide
Notes: The 2HP Performance Buffered Mult features 2 sets of 3 outputs as well as a SWITCH for disconnecting the 2nd input to make a total of 6 outputs. It's the perfect mult solution for live performance!
Read more
 2 in stock $69.24
Cat: 620648 Rel: 11 Aug 16
 
Envelope, oscillator & noise source synth module in Eurorack format - 2HP wide
Notes: EON is an envelope, oscillator, and noise source in 2 HP.

It has three modes that are quickly and easily set via a 3 position switch.

Its functionality is deep and multifaceted. The EON can be a full fledged envelope with linear and exponential shapes, a square wave oscillator that tracks 1 volt per octave, or a digital noise source with downsample control.

In addition to the three main functions, the EON also has a triangle wave LFO, random gates, and cycling envelopes.

Packing more features per HP than any other module before, the EON is the best way to fill any empty spot in your case.
Read more
 1 in stock $96.31
2hp
Cat: 620659 Rel: 11 Aug 16
 
Envelope generator synth module in Eurorack format - 2HP wide
Notes: Envelope generator with linear and exponential shapes. CV over decay time and end of attack gate output.

Specifications

Max Power Consumption: 43 mA +12V, 16 mA -12V

Depth: 34 mm (skiff friendly)

Width: 2hp
Read more
 1 in stock $96.31
2hp
Cat: 620664 Rel: 11 Aug 16
 
Random voltage generator synth module in Eurorack format - 2HP wide
Notes: Rnd is a random voltage generator and random gate source with an internal clock. The output is a quantized random voltage between 0V and 10V. The attenuator control provides fine-tuning of the random voltage.

This allows for a musically useful range to be defined. In addition, random gates are emitted from the gate output with an associated probability control while externally clocked.

Great for modulation and chaotic rhythmic events, Rnd is a universal solution for adding unpredictability to your system.

Specifications:

Max Power Consumption: 40 mA +12V, 16 mA -12V

Depth: 34 mm (skiff friendly)

Width: 2hp
Read more
 1 in stock $84.94
Cat: 739466
 
B-STOCK: Product has light surface marks/scratches, but otherwise in perfect working condition
Notes: ***B-STOCK: Product has light surface marks/scratches, but otherwise in perfect working condition***


Ring Modulator Module

- Trigger X
- Trigger Y
- In X
- In Y
- Out
Read more
 1 in stock $73.78
Cat: 633370 Rel: 28 Nov 16
 
Voltage distributor synth utility module
Notes: Warna is a very useful utility module that helps you to manage control voltages in the system. Crammed in just 6 hp, there are five normalled sections: two buffered mults, two inverters, and a summing mixer. Each multiple routes the input signal to separated outputs without loss in voltage. Warna is designed for unity gain - if you apply a specific voltage to any input, it remains the same on the respective outputs. Inverters are hardwired to mults and invert the polarity of the signal applied to them. Both mults are also normalled to the mixer section via inputs. Patching anything to these inputs breaks the normalization.

The top and the bottom section both are buffered 1-in-4 multiples. The input can be inverted with a switch, i.e. its polarity will be changed by 180 degrees. Four inverted copies are then available at the outputs, meaning you can use these two sections as inverter. Bi-polar LEDs display whether the signal is positive or negative: yellow = negative, red = positive. The centre section is a four-input summing stage with amplification factor 1, a so-called unity-gain mixer. The multiples are normalized to the mixer which can be deactivated by patching.
Read more
 2 in stock $83.31
Cat: 634773 Rel: 15 Dec 16
 
9 input/9 output pin matrix synth module - 24HP wide
Notes: The MTX9 presents a new take on an old classic - the pin matrix, famously incorporated into EMS and Maplin synthesizer designs. The MTX9 provides 9 inputs and 9 outputs to be patched to one another, whilst allowing for passive splitting of one input to several outputs and averaging summation of several inputs to one output (or more).

Each component of the matrix has been designed to use standard parts - the pins are 2mm banana test plugs and all cards of the matrix are easily replaceable. Whilst the matrix is currently passive, an active expander card will be available from FSS soon. The MTX9 is supplied with a dry-wipe marker and 10 banana pins as standard, with spares available from FSS.
Read more
 2 in stock $96.31
2hp
Cat: 748678
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


Mix is a 4 channel mixer that is great for audio or control voltage signals. Up to four inputs can be combined to a single output each with its own level control.
Read more
 1 in stock $92.92
2hp
Cat: 749829 Rel: 30 Dec 16
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


Mix is a 4 channel mixer that is great for audio or control voltage signals. Up to four inputs can be combined to a single output each with its own level control.
Read more
 1 in stock $92.83
2hp
Cat: 635858 Rel: 30 Dec 16
 
Clock divider/multiplier module
Notes: Div is a 2 channel, voltage controlled clock divider and multiplier. Incoming clock signals can be multiplied or divided by a factor of 16 with a multitude of values in between.

CV inputs provide external control of the current clock rate, allowing for the creation of dynamic rhythms from a single clock signal.
Read more
 2 in stock $91.97
Cat: 638093 Rel: 06 Feb 17
 
DIN/SYNC expander module in Eurorack format - 4HP wide
Notes: DIN SYNC is a 4 output expander module with selectable divide (1,2,4) for use with Malekko SYNC. Connects to SYNC via 6-pin cable (included).
Read more
 1 in stock $74.66
Cat: 621359 Rel: 14 Feb 17
 
Utility synth module in Eurorack format - 6HP wide
Notes: Bytom is a simple - yet very useful - utility module that allows you to combine various trigger/gate signal sources to obtain interesting rhythmic events, useful for sequencing, modulation and patch automation purposes. It can also be used for summing control voltages of a positive polarity. The module consists of three independent sections. Each one can process up to four signals fed to its inputs. All three sections can be normalled into one 12-signal combination via the manual switches. Either the upper or lower section can be combined with the middle section to form an 8-signal combination. Summed signals of two or three sections will appear on the middle section's output socket. The individual outs on upper and lower units remain active even when combined with the middle section.
Read more
 1 in stock $71.41
2hp
Cat: 638777 Rel: 21 Feb 17
 
Voltage controlled burst generator & trigger delay module
Notes: Brst is a voltage controlled burst generator and trigger delay. Upon receipt of a gate signal, Brst will output a stream of triggers. Knobs and CV inputs give the user control over speed and the number of repetitions. Whether you're generating bouncing balls, crafting IDM drum beats, or humanizing a clock signal, Brst will prove an indispensable addition to your rack.
Read more
 2 in stock $75.74
2hp
Cat: 638778 Rel: 21 Feb 17
 
Full featured two stage envelope generator module
Notes: EG is a full featured two-stage envelope generator. In addition to a colossal range from 3ms to 11 minutes per stage, EG features the ability to switch between linear and exponential curves on the fly, a built-in attenuator, and CV over attack and decay. Boasting more features than modules five times its size, EG can fill any envelope-sized gap in your system.
Read more
 1 in stock $84.39
2hp
Cat: 638773 Rel: 21 Feb 17
 
Dual linear VCA module with CV input attenuator & DC-coupled inputs
Notes: The 2hp VCA is a dual, linear VCA. It uses the renowned 2164 SSM architecture, giving it extremely low distortion and high quality audio outputs. With a CV input attenuator, and DC-coupled inputs this is your new go-to module for voltage controlled amplification of audio or CV.
Read more
 2 in stock $90.88
2hp
Cat: 638776 Rel: 21 Feb 17
 
Random sequence generator module
Notes: TM is a probabilistic random sequence generator based on the research of Alan Turing. His Turing machine was a mathematical model of computation that could, in theory, create any output based on a set of instructions and input variables. In a similar way, the TM chooses random values for steps in a sequence based on the user's probability settings. By manipulating probability and sequence length, the module can generate an infinite number of sequences. Whether you're looking for a controlled random source, or an evolving melody generator, TM has you covered.
Read more
 1 in stock $88.72
2hp
Cat: 638779 Rel: 21 Feb 17
 
Four stage linear envelope module with two expressive ranges
Notes: ADSR is a four stage linear envelope with two expressive ranges. Each stage can be modified independently allowing for the creation of complex, multi-segment envelopes. Great for modulating filters, VCAs, and oscillators.
Read more
 2 in stock $84.39
2hp
Cat: 730104
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


ADSR is a four stage linear envelope with two expressive ranges. Each stage can be modified independently allowing for the creation of complex, multi-segment envelopes. Great for modulating filters, VCAs, and oscillators.
Read more
 1 in stock $69.84
Cat: 641955 Rel: 27 Feb 17
 
CV/Gate expansion module for Mimetic Sequent
Notes: Mimetic Multium provides the three patterns out simultaneously as well as four randomized rhythm sources.
Read more
 1 in stock $81.15
Cat: 641960 Rel: 27 Feb 17
 
Simple attack-release envelope with voltage controlled clamp
Notes: The Sinclastic Empulatrix was inspired by the simple - yet remarkably clever - envelopes used in the cymbals of the TR-808. These envelopes are simple exponential decays that are applied to the signal via clamping rather than the more typical scaling. For binary signals such as a square wave a clamping VCA will sound like a typical VCA. For analog signals it will add a clipping effect that gets stronger as the envelope decays.

The Sinclastic Empulatrix has knobs for control of attack and release.

The envelope is controlled by a gate input that determines the timing of the envelope. The envelope is also scaled by the voltage of the gate so it can be used to control the amplitude of the envelope.

The clamping VCA section of the Sinclastic Empulatrix has a simple input and output. It is DC-coupled so is suitable for control voltages and can be used without the envelope generator by turning the attack and release fully counter-clockwise and driving the gate with an analog CV.

This module can also be used as an asymetric slew: the envelope output will track the gate input but will be slewed by the attack and release times based on relative voltage.

Size: 4HP Eurorack
Depth: 1 Inch
Power: 2x5 Eurorack
Draw +12V: 15 mA
Draw -12: 25 mA
Read more
 1 in stock $88.72
Cat: 641963 Rel: 27 Feb 17
 
Six switches module in 8 HP
Notes: Variatic Basicus is six momentary switches debounced for drivng gates. It is a simple, useful gate control surface for Eurorack.

Size: 8HP Eurorack
Depth: 1 Inch
Power: 2x8 Eurorack
Draw +12V: 20 mA
Draw -12: 0 mA
Read more
 1 in stock $85.48
Cat: 637039 Rel: 22 Mar 17
 
Dedicated switch module for Minimod, VCF/VCA gain jumper settings, plus 6-way multiple - dark edition
Notes: AJH Synth have had quite a few customers asking if we can make the gain jumpers on the MiniMod VCF and VCA modules accessible from the front panel, so this 2HP module aims to address this.

The Gain Switch Multi has two switches which connect to the gain jumpers on the VCA and VCF. Switch "up" is the same as having the gain jumper in place, switch "down" is the same as removing the jumper, and gives higher gain.

Using these switches gives a similar effect to the old "headphone out to external input" trick on the original Model D but with a much wider overdrive range, particularly from the VCA.

As an added bonus, AJH Synth have also included a six way passive multi.
Read more
 1 in stock $74.65
Cat: 643381 Rel: 27 Mar 17
 
Lo-fi digital reverb effect unit
Notes: Digiverb is a lo-fi reverb effect unit that uses an Accutronic digital reverb "tank" module. The sound is somewhere between a virtual spring reverb and a dense multi tap delay but the effect is quite musical and interesting.

Use the Digiverb as a simple and fun way to add some extra dimensions to your patches!
Read more
 2 in stock $77.90
2hp
Cat: 649106 Rel: 11 May 17
 
MIDI Eurorack module
Notes: MIDI is a plug and play solution for interfacing with your computer or MIDI hardware. Four modes provide monophonic, duophonic, dual mono, and quad trigger operation.

MIDI clock, CC messages, and note on messages are all easily accessible between the four modes. The status LED provides clear indication of MIDI data being received by the module. Class compliant MIDI device on Mac/PC/Linux. Get connected with MIDI.
Read more
 1 in stock $90.88
2hp
Cat: 649107 Rel: 11 May 17
 
Analog, voltage controlled low pass filter
Notes: LPF is a four-pole, voltage controlled low-pass filter. Its 24 dB per octave slope and OTA topology provide a smooth, buttery character. Resonance can be pushed to self oscillation, turning it into a sine wave VCO with accurate 1V/oct tracking across four octaves.

In addition, CV over resonance gives dynamic sound shaping possibilities under voltage control. Hit the slope with LPF.
Read more
 2 in stock $85.48
Cat: 648932 Rel: 25 May 17
 
Expander module for Pamela's New Workout - 2HP
Notes: Pexp-2 is an expander module for Pamela's NEW Workout offering additional dedicated fixed clocked outputs.

Extend Pam as a master to clock external gear with a super solid MIDI & Din Sync dedicated clock outputs.

Use extra fixed jack clocked gate outputs to free up Pamela outputs for more exotic modulation duties.

Connects to, and powered by, expander header on rear of Pamela's NEW Workout. Only a single expander is supported at any time.
Read more
 1 in stock $80.06
Cat: 637403 Rel: 05 Jun 17
 
6HP Eurorack stereo headphone amp/line out module with stereo 1/4" headphone amplifier output & dual-mono 1/4" line-level outputs
Notes: The best way to get sound out of a modular. Outs is a dual independent output module featuring a stereo 1/4" headphone amplifier output and dual mono 1/4" line level outputs.

Left and Right inputs are available. If only the left input is used, it is sent to both the Left and Right outputs.
Read more
MRP:$123.36 SAVE 22%
 1 in stock $96.31
2hp
Cat: 752017 Rel: 02 Aug 17
 
B-STOCK: Item refurbished, repaired and in perfect working order.
Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


Comb is an IIR peaking comb filter with control over cutoff frequency, resonance that can be driven into self oscillation, and a dampening filter in the feedback path. An incredibly short, tuned delay line will alter the character of your input by imposing harmonic peaks on the source. Subtle settings can result in thickening timbres, reminiscent of phaser-like effects, while more extreme settings can create lustrous string sounds from white noise, or tear your waveform to shreds. Explore new sonic territory with Comb.
Read more
 1 in stock $94.79
Cat: 659944 Rel: 27 Sep 17
 
Expander module for Radar - 8HP
Notes: BLIP is an expander for RADAR adding a whole host of new features, such as; envelope inversion, ignore triggers, envelope sequencing, envelope delay, envelope roll, level, shape and attack, decay or both swapping, equal/opposite swapping, 8 preset locations, CV recall, and a full suite of random functions!

The BLIP expander provides an extreme variety of extra controls and outputs, making the Radar more powerful than it already is.
Read more
 1 in stock $96.31
Koma Elektronik Field Kit Expansion Pack (expansion/accessory pack)
Cat: 663392 Rel: 26 Oct 17
 
Expansion pack for the Koma Elektronik Electro Acoustic Workstation
Notes: It's all about the things you connect to the The Field Kit! To get you started, Koma Elektronik have decided to offer an Expansion Pack with a bunch of different sources that you can use and connect to create your own signature sounds.

The Expansion Pack contains:

- 2 x Contact Microphones: Use these contact microphones to pick up vibration or sound, they are an amazing versatile input source
- 1 x Electro-Magnetic Pickup: This guy is good at picking up changes in magnetic fields, you can use it to amplify a string like a guitar pickup or amplify a spinning motor
- 1 x Solenoid push-pull motor: Use the solenoid to hit things, together with the DC Interface the solenoid can make anything rhythmical and percussive
- 1 x DC motor: The Motor can be used to rotate things or as a noisy oscillator together with the Electro-Magnetic Pickup
- 1 x small speaker: Use the speaker to listen to the main mix or as a sound source and to feedback sounds
- 3 x patch cables Always handy to have around to patch up different parts of your Field Kit... and a bunch of little objects to play with (little springs, marbles)

The new KOMA Elektronik Field Kit is the perfect tool for everyone who would like to experiment with electro acoustic sound. Use everyday objects, amplify them and use them to make sound, like our heroes John Cage and David Tudor used to do!

The Field Kit is optimized to process signals from microphones, contact microphones, electromagnetic pickups and able to run DC motors and solenoids. On top of that it can receive radio signals and convert signals from switches and sensors into control voltage!
Read more
 1 in stock $61.67
2hp
Cat: 667366 Rel: 31 Oct 17
 
Rhythmic pattern generator
Notes: Euclid is a rhythmic pattern generator based on ideas originally presented by Euclid, the Greek mathematician. The Euclidean algorithm can be adapted to create rhythms by taking the total number of active steps in a sequence, and then distributing them across the entirety of the pattern.

This creates cyclical rhythms that are immediately musical and can be used for everything from EDM to IDM. Bring your patches full circle with Euclid.
Read more
 2 in stock $95.21
150/199(ページ1/4)の商品
1  2  3  4  »

Filter

Synth modules
DJ機器
Release Date
Close