安全なお買い物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全なお買い物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Synth modules

View:
Options
150/196(ページ1/4)の商品
1  2  3  4  »
Subscribe to our weekly Studio Equipment emails
FORTHCOMING
4ms Listen Up Passive Expander Module For Listen Modules
coming soon $65.91
FORTHCOMING
Doepfer A-170v Dual Slew Limiter Module (vintage edition)
Cat: 751702
 
Two separate slew limiters for generating portamento effects - 8HP
Notes: Module A-170 contains two separate slew limiters, also known as portamento controllers or integrators. The first SL has just one joint control, which sets both rise and fall times (c. 0 ...10 sec). The second SL has separate controls for rise and fall times, and can therefore be used as a simple AR envelope generator. Over and above this, you can set the overall range for these parameters, with a three-position switch, as on the full ADSRs.

Both slew limiters have two LEDs each, to show the state of the rising and falling voltages.


Additional technical remarks: If the upper slew limiter is used for precision applications (e.g. portamento/glide of one or more VCOs) a buffer (e.g. A-185-1 or A-185-2) is recommended between the A-170 output and the VCO(s) input(s). The reason is a small voltage drop that is caused by the protection resistor at the A-170 output. An A-185-1 or A-185-2 connected between the A-170 and the VCO(s) avoids that voltage loss. For all A-170 manufactured later than May 2009 (recognizable by the label "Version 2" on the pc board) this remark is not valid as these modules are equipped with an additional voltage buffer at the output.

The lower slew limiter cannot be used for precision applications because of the voltage loss caused by the diodes of the circuit.
Read more
coming soon $77.81
FORTHCOMING
Doepfer A-172 Maximum/Minimum Selector & Rectifier Module
Cat: 751706
 
Module for processing/mixing of control voltages - 4HP
Notes: A-172 is a minimum/maximum selector module and is equipped with four analogue inputs and two analogue outputs (minimum, maximum). The main application of the module is the processing/mixing of control voltages, e.g. random voltages, ADSR, LFO, S&H, ribbon CV, theremin-CV and similar, but even for audio signal processing the module can be used (e.g. several outputs of the same or different VCOs).

The module permanently picks the maximum resp. minimum voltage out of the four input signals and outputs these voltages to the maximum resp. minimum jack socket.

To adjust offset and amplitude for each input independently (i.e. to bring the signal into the right "position" with the desired level) we recommend combining the module with the A-129-3 Slew Limiter/Attenuator/Offset Generator (see patch example below). The other sketch below shows the basic principle of the max/min module by means of three sine waves (e.g. three LFOs) with different frequencies and different levels.

The module can be used also as a simple half-wave rectifier.
Read more
coming soon $51.06
FORTHCOMING
Doepfer A-174-2 Modulation Wheels CV Source Module
Cat: 751707
 
Modulation wheel module with two wheels - 14HP
Notes: A-174-2 is a modulation wheel module with two wheels. The factory setting is a spring loaded wheel at the left side with bipolar voltage output (i.e. 0V in centre position, positive voltage in the upper range, negative voltage in the lower range, voltage range about -5.5 V ... 0V ... +5.5 V) and a wheel without spring at the right side with positive voltage output (i.e. 0V in the lowest position and positive voltage when operated, voltage range about 0...+8 V). For the spring loaded wheel a voltage "plateau" around 0 V is preset (jumper) so that the output voltage is 0 V in a small area near the centre position.

By means of jumpers the factory settings can be changed. For each wheel two jumpers are available: one for the voltage range (positive or bipolar) and one for the voltage plateau around 0 V. If these settings are changed even the wheels have to be re-adjusted mechanically. Therefore, such modifications should be carried out by a qualified person only. By request the module is available from the factory even with two wheels both with or without springs (additional charges Euro 10.00 for each change).

Important note for module mounting: As the potentiometer of the left wheel projects about 10 mm the rim of the front panel a 2 or 4 HP blind panel has to be mounted left from the module - unless the module left to the A-174-1 has sufficient space in this area (e.g. A-174-1).
Read more
coming soon $77.81
FORTHCOMING
Doepfer A-177-2 External Foot Controller II Module
Cat: 751715
 
Foot controller interface - 8HP
Notes: Economically priced module for connecting one foot controller and one double foot switch for control A-100 functions by means of the feet. For example, the frequency of a filter or the loudness can be controlled by a foot controller, but even other parameters like LFO frequency, modulation depth, phasing, pitch or any other voltage controlled parameter. The gate outputs controlled by the double foot switch can be used e.g. to trigger an envelope generator or to start/stop a sequencer. Even a single foot switch can be used if only one gate signal is required.

A special application of the A-177-2 is the usage within a Trautonium replica. The foot switches can be used to switch the mixtures of the subharmonic oscillator A-113. The foot controller can be used to control the overall loudness in combination with a VCA.

A-177 is compatible with the foot controllers FP5 and double foot switch VFP2. The Foot controller and double foot switch are not included with the module. If you want to use another foot controller or foot switch it has to be compatible to FP5 or VFP2.

If the foot controller FP5 is used the CV output range is about 0...+8V. The gate output levels are 0/+12V in combination with the VFP2 (foot switch not operated = 0V, foot switch operated = +12V).
Read more
coming soon $52.95
FORTHCOMING
Doepfer A-178 Theremin Control Voltage Source Module
Cat: 751716
 
Theremin controller module - 8HP
Notes: Theremin module for generating a variable control voltage by approaching/removing hand to/from an antenna. The distance range is about 30-40 cm. Additionally the module is equipped with a Gate output with adjustable threshold level. Controls/Inputs/Outputs: antenna input, offset (knob for zero adjust), 2 x CV out, 2 x LED (for CV control positive/negative and zero offset adjust).

To simulate the original Theremin two A-178, a VCO (e.g. A-110) and a linear VCA (e.g. A-130 or A-132) are required. But of course the A-178 can be used to control other functions in the A-100 (e.g. filter frequency, modulation depth and/or speed, tempo, attack/decay time and so on).

The CV output voltage of the A-178 can range - according to the setting of the front panel controls - from -10V...+10V. The gate output switches from 0V to about +10V.

Applications:

- Controlling any voltage controlled parameter of the A-100, e.g. pitch or pulsewidth (VCO A-110), loudness (VCA A-130/131/132), panorama (A-134), filter frequency or resonance (A-120/121/122/123), phasing (A-125), frequency shift (A-126), resonance peaks (A-127), envelope parameters (A-141/142), tempo (A-147)

- Triggering of A-100 activities via gate with adjustable threshold, e.g. starting an envelope (A-140/141/142), Start/Stop of a sequence (A-155), any switching function (A-150/151)

- Conversion into MIDI control change messages is possible with the A-192.

If two or more A-178 are used the distance between the modules/antennas should be at least 40-50 cm. Otherwise the antennas may affect each other.
Read more
coming soon $96.18
FORTHCOMING
Doepfer A-185-2 Precision Control Voltage Adder & Buffer Module
Cat: 751763
 
Precision adder (mixer) and buffer for control voltages - 6HP
Notes: Module A-185-2 is a precision control voltage adder/buffer. Precision means that the amplification of the inputs without attenuators is exactly 1.00 and is suitable to add control voltages for the pitch control of VCOs (e.g. from keyboard + sequencer 1 + sequencer 2). Summing resistors matched to 0.1% are used to obtain an accuracy of 0.1% for the added voltages.

The module is equipped with four CV inputs: one with attenuator and three without attenuator. Each input is normalled to +1 V (i.e. if no plug is inserted the input contributes 1 V to the sum appearing at the output).

The input with attenuator can be used for common modulations (e.g. from an LFO, ADSR, Theremin, Pitch-Bender) for all VCOs connected to the output. The Lev.1 control is used to adjust the depth of the modulation, the first switch selects the polarity of the modulation. If no signal is connected to the first socket the attenuator works as a (fine) tuning knob because a voltage in the range 0...+1V (right position of the switch) or 0...-1V (left position of the switch) is added to the CV output.

The inputs without attenuators are planned to add control voltages coming out of keyboards, sequencers, Midi-to-CV interfaces, ribbon controllers or other CV sources that follow the 1V/oct standard. For example the CV of a keyboard can be used to transpose the CV coming from a sequencer, or the CV of a slow sequencer can be used to transpose the CV from a fast sequencer.

Each input is equipped with a three-position switch that determines if the corresponding voltage is added (right position), subtracted (left position) or if the input has no effect (centre position). If no plug is inserted the corresponding switch works as an octave switch for the lower three sections as the default 1 V are added or subtracted to the output voltage according to the switch position. The first switch can be used to add a variable voltage to the sum output. The variable voltage is adjusted with the Lev.1 control and the knob works then as kind of a (fine) tuning control.

The module is equipped with 4 outputs: three non-inverting and one inverting ouput. An internal jumper can be used to connect the non-inverted or inverted output to the CV line of the A-100 bus. That way the module can used to control several VCOs that are connected to the same bus board as the A-185-2 (same functionality as A-185-1).
Read more
coming soon $72.40
FORTHCOMING
Doepfer A-185-2v Precision Control Voltage Adder & Buffer Module (vintage edition)
Cat: 751764
 
Precision adder (mixer) and buffer for control voltages - 6HP
Notes: Module A-185-2 is a precision control voltage adder/buffer. Precision means that the amplification of the inputs without attenuators is exactly 1.00 and is suitable to add control voltages for the pitch control of VCOs (e.g. from keyboard + sequencer 1 + sequencer 2). Summing resistors matched to 0.1% are used to obtain an accuracy of 0.1% for the added voltages.

The module is equipped with four CV inputs: one with attenuator and three without attenuator. Each input is normalled to +1 V (i.e. if no plug is inserted the input contributes 1 V to the sum appearing at the output).

The input with attenuator can be used for common modulations (e.g. from an LFO, ADSR, Theremin, Pitch-Bender) for all VCOs connected to the output. The Lev.1 control is used to adjust the depth of the modulation, the first switch selects the polarity of the modulation. If no signal is connected to the first socket the attenuator works as a (fine) tuning knob because a voltage in the range 0...+1V (right position of the switch) or 0...-1V (left position of the switch) is added to the CV output.

The inputs without attenuators are planned to add control voltages coming out of keyboards, sequencers, Midi-to-CV interfaces, ribbon controllers or other CV sources that follow the 1V/oct standard. For example the CV of a keyboard can be used to transpose the CV coming from a sequencer, or the CV of a slow sequencer can be used to transpose the CV from a fast sequencer.

Each input is equipped with a three-position switch that determines if the corresponding voltage is added (right position), subtracted (left position) or if the input has no effect (centre position). If no plug is inserted the corresponding switch works as an octave switch for the lower three sections as the default 1 V are added or subtracted to the output voltage according to the switch position. The first switch can be used to add a variable voltage to the sum output. The variable voltage is adjusted with the Lev.1 control and the knob works then as kind of a (fine) tuning control.

The module is equipped with 4 outputs: three non-inverting and one inverting ouput. An internal jumper can be used to connect the non-inverted or inverted output to the CV line of the A-100 bus. That way the module can used to control several VCOs that are connected to the same bus board as the A-185-2 (same functionality as A-185-1).
Read more
coming soon $79.97
FORTHCOMING
Doepfer A-184-2 Voltage Controlled Crossfader & Triangle To Sine Waveshaper Module
Cat: 751758
 
Sine converter/VC crossfader - 4HP
Notes: Module A-184-2 is the combination of two functions and planned primarily as an expansion module for VCOs or LFOs (e.g. A-110-1, A-110-2, A-145, A-147-2).

Triangle-to-Sine Waveshaper:

The upper section is a very precise triangle-to-sine converter (thanks to Tim Stinchcombe who recommended this circuit). It can be used to convert any triangle waveform into a (nearly) perfect sine. The converter is much better than the simple diode converter used in the A-110-1, A-111-1, A-145 and A-147-2. Two trimming potentiometers are used to optimize the sine shape. The converter should be assigned to one VCO or LFO because the trimming potentiometers have to be re-adjusted if the input level or DC offset of the input signal changes. If the trimming potentiometers are deliberately mis-adjusted it can be used also as a waveshaper for non-sine waveforms (e.g. sine-shaped at the top of the signal and a peak at the bottom, even voltage controlled by applying an additional voltage to the waveshaping circuit, "circuit-bending" notes will be available).

The waveform converter is DC coupled and can be used also for low frequencies (e.g. LFO triangle waves).

Voltage Controlled Crossfader:

The lower section is a voltage controlled crossfader. It has two inputs A and B. The two signals are mixed together with variable percentage. When the manual control CF is fully CCW only signal A appears at the CF Out socket. When the manual control CF is fully CW only signal B appears at the CF Out socket. In the centre position of the manual control both signal appear with the same level. In addition a control voltage input CV with attenuator is available to enable voltage control of the crossfade.

Two LEDs display the crossfading shares of input A and B.

The crossfader uses two high quality VCAs (SSM2164). Inputs and outputs are DC coupled. Consequently it can be used for audio signals and slowly varying control voltages as well.

The sockets of the upper section (triangle and sine) are normalled to the inputs A and B of the crossfader section. That way the crossfader is used to fade between triangle and sine of the VCO or LFO connected to the waveshaper. If other signals are plugged into the input sockets A and B these signals are used for crossfading.

The main application is to fade between two different waveforms of a VCO or LFO or two different VCF outputs. But the module can be used for any other signals too as the waveshaper and crossfader sections are independent apart from the normalled sockets.
Read more
coming soon $81.59
FORTHCOMING
Doepfer A-185-1 Active Bus Access Module
Cat: 751760
 
Provides input & output access to your Eurorack's internal CV/Gate bus
Notes: Active bus access module to feed CV and Gate into the A-100 bus (e.g. when using more than one frame or with external CV/Gate interfaces). Miniature jack sockets for CV In, Gate In, 2xCV Out, 2xGate Out, 2 LEDs for CV/Gate control

In general, the A-185 is recommended as soon as more than 2 VCO's (A-110, A-111) are controlled by the same control voltage source. Without interconnection of the A-185 in this case tuning inaccuracies (scale) may occur. The A-185 is mounted close to the VCOs. The controlling voltage for all VCOs is applied to the CV In socket of the A-185. By means of the CV line of the bus board the CV is connected to all VCOs at the same bus board.
Read more
coming soon $52.95
FORTHCOMING
Doepfer A-170 Dual Slew Limiter Module
Cat: 751699
 
Two separate slew limiters for generating portamento effects - 8HP
Notes: Module A-170 contains two separate slew limiters, also known as portamento controllers or integrators. The first SL has just one joint control, which sets both rise and fall times (c. 0 ...10 sec). The second SL has separate controls for rise and fall times, and can therefore be used as a simple AR envelope generator. Over and above this, you can set the overall range for these parameters, with a three-position switch, as on the full ADSRs.

Both slew limiters have two LEDs each, to show the state of the rising and falling voltages.


Additional technical remarks: If the upper slew limiter is used for precision applications (e.g. portamento/glide of one or more VCOs) a buffer (e.g. A-185-1 or A-185-2) is recommended between the A-170 output and the VCO(s) input(s). The reason is a small voltage drop that is caused by the protection resistor at the A-170 output. An A-185-1 or A-185-2 connected between the A-170 and the VCO(s) avoids that voltage loss. For all A-170 manufactured later than May 2009 (recognizable by the label "Version 2" on the pc board) this remark is not valid as these modules are equipped with an additional voltage buffer at the output.

The lower slew limiter cannot be used for precision applications because of the voltage loss caused by the diodes of the circuit.
Read more
coming soon $62.68
FORTHCOMING
Doepfer A-175 Dual Voltage Inverter Module
Cat: 751709
 
Two identical inverters - 4HP
Notes: Module A-175 (Dual Voltage Inverter) is exactly what it says it is: two identical inverters, which will take a voltage and output it in an inverted form - so that an input of +5 V will be output as -5 V, an input of -2 V will be output as +2 V, and so on. Two LEDs give a visual indication of the (positive or negative) output signal.
Read more
coming soon $52.95
FORTHCOMING
Doepfer A-176 Control Voltage Source Module
Cat: 751711
 
Three independent voltage sources - 8HP
Notes: Module A-176 (Control Voltage Source) provides three voltage sources, to use wherever an extra CV is required. The top two voltage sources (CV 1 and CV 2) have controls for coarse and fine control of the voltage output; the third source (CV 3) just has the one control.

The range of the voltages output can be preset, either to 0 to +5 V or to -2.5 V to +2.5 V depending on your likely requirements. There is a jumper on the circuit board for each of the three voltage sources.

A typical use for the module would be to provide fine as well as coarse tuning for an A-110 standard VCO, (which, unlike the A-111, only has one tune control).

In general, this module will be useful whenever you need a manually controllable CV on a module which doesn't itself have a built-in control.
Read more
coming soon $62.68
FORTHCOMING
Doepfer A-182-1 Switched Multiples Module
Cat: 751724
 
Eurorack passive multi-connector - 6HP
Notes: Module A-182-1 is a simple passive multi-connector similar to the multiples modules A-180-1/A-180-2. In contrast to modules A-180-1/2 each socket is equipped with a 3-position switch that allows to connect the corresponding socket to the internal bus #1 (left position), bus #2 (right position) or to turn the socket off (centre position).

Examples:

- All switches in left position or all switches in right position: 8-fold multiple

- Four switches in left position and four switches in right position: two 4-fold multiple

- X switches in left position, Y switches in right position and Z switches in centre position: two separate multiples with some sockets turned off
Read more
coming soon $52.95
FORTHCOMING
Doepfer A-184-1 Ring Modulator, Sample & Hold, Track & Hold, & Slew Limiter Module
Cat: 751756
 
4HP Eurorack module featuring a combination of 3 functions
Notes: Module A-184-1 is the combination of three functions:

- Ring Modulator
- Sample&Hold/Track&Hold unit
- Slew Limiter

The same functions are actually already available in other modules (e.g. A-114, A-148, A-170). But in many systems it's not necessary to have two ring modulators (A-114) or two S&H units (A-148) or two slew limiters (A-170) available. That's why we have compiled these function in one small 4 HP module.

The upper section is nothing but half of an A-114, i.e. a ring modulator with the usual X/Y inputs and the X*Y output. Inputs and outputs of this sub-unit are AC coupled, i.e. suitable only for audio signals. A detailed explanation of a ring modulator can be found on the A-114 info page.

The lower section is a Sample & Hold (S&H) / Track & Hold (T&H) unit (same as half of an A-148) followed by a slew limiter (same as the upper section the A-170). A toggle switch is used to set the mode to S&H or T&H. In S&H mode the unit picks out a sample from the voltage at the SH input at the rising edge of the trigger signal input. In T&H mode the output follows the input voltage as long as the level of the trigger signal is high. As soon as the trigger signal turns low, the last voltage is stored. The trigger input is internally normalled to high, i.e. the unit works just as a slew limiter in T&H mode when no trigger signal is applied.
Read more
coming soon $96.18
Cat: 732852 Rel: 27 Sep 19
 
Ring modulator with internal oscillator
Notes: Erica Pico Ring is a balanced modulator (quadrant multiplier) circuit to create bell-like, metallic or robotic sounds. It has built-in sine-wave modulation oscillator for more versatility.
Read more
 1 in stock $98.33
MFB
Cat: 695604 Rel: 16 Sep 19
 
MFB-522/Tanzbar style analogue bass drum module
Notes: The Bass-522 module is based on the 522 circuit and offers a punchy attack, long decay and wider pitch range. Adjustable noise and pitch envelope have also been added.

The sound can be triggered by Gate, M-Bus and signals like piezo pickups, dynamic mics and drum pads. The Sense parameter decides the sensibility and dynamic of attack, amplitude. decay and pitch.

The following parameters are available and can be controlled by CV:

TONE dampens the attack transient.
DECAY sets the release time of the amplitude.
TUNE defines the basic pitch from around 35 to 70 Hz.
PITCH controls the amount of pitch envelope.
NOISE mixes the noise floor (no CV control).

The module offers the new developed M-Bus connector which means you can you control everything via MIDI/CV interface or the new MFB SEQ-01 Pro Drum Sequencer without additional patching. The following addresses are supported:

Trigger with Velocity - MIDI Note #35 or #36 (switchable) and controller values for Tone, Decay, Tube, Pitch and Noise Decay.

The module has a width of 8HP (40mm).
Read more
 4 in stock $85.37
MFB
Cat: 695615 Rel: 16 Sep 19
 
Classic envelope generator - 8HP
Notes: The ADSR module is a voltage-controlled envelope generator. Normally, the characteristic is logarithmic, but a linear part can be added. With the help of the loop button, the envelope can also be used as an LFO, then Attack and Decay determine the frequency that goes far beyond 100 Hz. Another special feature is the CV inputs for Attack, Decay and Release. This can be used e.g. control or modulate the times externally. In addition to the normal output, there is an inverted output in parallel.

The power consumption is +/- 30 mA. The module has a width of 8 HP (40 mm).
Read more
 1 in stock $81.05
MFB
Cat: 695618 Rel: 16 Sep 19
 
Analogue VCA with built-in oscilloscope
Notes: The Visual VCA is a voltage controlled, analogue amplifier module with additional waveform display. The signal amplification can be regulated via the two CV inputs. CV1 is usually controlled by the envelope. A special feature is CV2, because this input can only be used in conjunction with CV1 and is normally used for modulation effects. The integrated oscilloscope represents the waveform of the input signal and has a resolution of 128 x 64 pixels. With the interval controller you can set the sampling frequency.

The power consumption is +/- 30 mA. The module has a width of 8 HP (40 mm).
Read more
 2 in stock $89.70
MFB
Cat: 695619 Rel: 16 Sep 19
 
Analogue 24db lowpass filter - 8HP
Notes: The 24dB VCF SSI is a voltage controlled analogue low pass filter module with the new SSI2144 chip. In addition, it has a 12dB output that works either as a low pass or bandpass (+/- 12dB). There are two inputs, one with attenuator. Another CV input with attenuator is available for the cut-off frequency. The resonance is controlled either via a controller or via another CV input with attenuator.

The power consumption is +/- 30 mA. The module has a width of 8 HP (40 mm).
Read more
 2 in stock $73.47
Cat: 751442 Rel: 17 Sep 19
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


TOPOGRAF is a drum sequencer with three tracks, that works with a "topographic" principle; it contains a number of drum patterns arranged in a "virtual map"; and with two knobs MAP X and MAP Y you can set a position in this map. With one knob per channel the density is defined; and a CHAOS knob brings some randomness into the whole process. All in all, a few knobs for a lot of drum patterns you probably wouldn't make this way by yourself - a nice source of inspiration and also great for playing live.

TOPOGRAF is the AE modular version of the Grids module by Mutable Instruments. It is 100% identical to Grids.
Read more
 1 in stock $71.70
Cat: 746964 Rel: 17 Sep 19
 
Synth module featuring two separate voltage processors
Notes: The upper voltage processor features four inputs which are mixed and inverted at the output. Inputs 2 and 4 have their own attenuator. Input 2 is normalised to a positive fixed voltage source, which may be attenuated, and appears inverted at the output, useful for applying negative offsets.

The lower voltage processor features two inputs which are mixed and inverted at the output. Input 2 has its own attenuator. Input 2 is normalised to a negative fixed voltage, which may be attenuated, and appears inverted at the output, useful for applying positive offsets.
Read more
 2 in stock $89.70
Cat: 744065 Rel: 17 Sep 19
 
4 input audio & CV mixer
Notes: Volts Platz has 4 inputs with attenuators. Input 3 is normalled to +ve for positive offsets (up to +8V), input 4 is normalled to -ve for negative offsets (down to -8V).

The first opamp stage now includes a switch to select x1, x2 or x10 amplification. You can take a direct (inverted) output from this stage.

The second opamp features switchable clipping diodes (LEDs) which clip anything above/below +/-5V. So 'normal' Euro signals go through unaffected. Flick the amplification switch and things gets dirty.

Patch a post-VCF signal into input 1. You can then use a combination of offsets at inputs 3 and 4, and CV into input 2 to explore modulated symmetric and asymmetric clipping.

Scale, offset, amplify, clip. Or just use it as a 4 input mixer.
Read more
 1 in stock $89.68
MFB
Cat: 695610 Rel: 16 Sep 19
 
Stereo drum mixer - 12HP
Notes: The DRUM-99 module is an audio-mixer that has been designed for the modules of the MFB-DRUM series but also for usage with other manufacturer's modules. When using multiple drum-modules in a modular system, the following processing stages like filters or VCAs often lack enough audio inputs. To route a complete drum-set through a filter, a separate mixer like the DRUM-99 comes handy.

DRUM-99 offers five monaural inputs with individual level control. Tiny trim-controls are used to set the channel panorama position for the internal stereo-bus.

A fixed level stereo-input can accommodate the signal of one or more additional DRUM-99 modules. These inputs can also be used with the DRUM-06 module (Tom Tom) that also offers a stereo-output.

All five mono signals and the stereo-input are routed to the stereo-output that can be connected to two VCAs, filters or other sound manipulating devices. The output may also be used to connect the DRUM-99 to a mixing-console or audio-interface.

The stereo-output is designed for a possible summing with additional stereo-outputs.

The module has a width of 12 HP (60mm).
Read more
 1 in stock $74.57
MFB
Cat: 695617 Rel: 16 Sep 19
 
Analogue VCO, switchable to DCO
Notes: The VCO/DCO is a voltage controlled analogue oscillator module. This can also be used as a DCO, eliminating the need for heating and temperature sensitivity. All functions except for the FM input are also available with the DCO. Sawtooth, triangle, rectangle and pulse are available as waveforms, with soft switching between the individual waveforms. This can also be done with a control voltage, so you have additional PWM modulation.

The power consumption is +/- 30 mA. The module has a width of 8 HP (40 mm).
Read more
 1 in stock $98.34
MFB VC LFO Module (synth module)
MFB
Cat: 695621 Rel: 16 Sep 19
 
Voltage controlled LFO, switchable to oneshot mode
Notes: The module VC LFO accommodates a slowly oscillating oscillator, which is primarily used for modulations. It has five waveforms, CV input with attenuator and a control range from 10 seconds to 100 Hz. In addition, the LFO has its own reset input, over which the waveform is restarted. If you set the speed accordingly and have a separate reset pulse, you can synchronize the LFO with a sequencer. The following waveforms are available: rising sawtooth, triangle, falling sawtooth, rectangle and sample & hold.

The output voltages are maximum +/- 5 volts. The module has a width of 8 HP (40mm).
Read more
 4 in stock $73.49
FORTHCOMING
Intellijel Duatt 1U Module
Cat: 747516
coming soon $75.64
FORTHCOMING
Intelijel FSR 1U Module
Cat: 747522
coming soon $79.97
Cat: 745792 Rel: 10 Sep 19
 
Dual trigger modifier, consisting of two trigger inverters for gate, clock or trigger signals - 4HP
Notes: Module A-165 (Dual Trigger Modifier) contains two separate trigger modifiers, to use with logical/digital levels (gate, clock, trigger). Each half of the module enables signals generated by the A-100 to communicate with other instruments (such as an external sequencer) or is simply used where you want to reverse a trigger polarity.

Whatever signal is patched into the input, inverted by the module, and fed out of the Inv. Out (inverted output) socket. At the same time, a trigger signal of roughly 50 ms is generated every time an edge of the trigger pulse is sensed (negative as well as positive). This trigger signal is available at the +/- output.

Two LEDs act as indicators showing the level of signal available at the two outputs.

When both units are daisy-chained the module can be used as level shifter for gate/trigger/clock signals (from min. +2,5V up to +12V)
Read more
 1 in stock $60.52
Cat: 745778 Rel: 10 Sep 19
 
Two independent voltage controlled switches in one module - 4HP
Notes: Module A-150-1 (Dual VCS) contains two separate voltage-controlled switches.

Each switch has a control voltage input, a common Out / Input, and two In / Outputs. The switches are bi-directional: they can work in both directions, so can connect one input to either of two outputs, or either of two inputs to one output. Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Two LEDs show which in / output is active (i.e. which is connected to the common out / input).
Read more
 2 in stock $54.02
Cat: 742136 Rel: 10 Sep 19
 
Buffered precision multiple - 4HP
Notes: Erica Synths Black Multi is highly accurate active buffered 2x1to3 or 1to6 multiple that will work for signal splitting in any circuit, including driving several VCOs in tune from one CV source. "Octave" or +/- 1V offset switches on both channels allow to add or subtract one volt form each channel thus transposing VCOs one octave up or down. Hidden feature - custom offset - allows to set user defined offset on the first channel.
Read more
 3 in stock $79.96
Cat: 745791 Rel: 10 Sep 19
 
Simple & effective voltage-controlled frequency divider - 8HP
Notes: Module A-163 is a voltage controlled audio frequency divider. The frequency of the input signal (preferably the rectangle output of a VCO) is divided by an integer factor N (N = 1, 2, 3, 4 ... up to 32). N can be adjusted manually and modulated with an external control voltage (e.g. from LFO, ADSR, Random, MIDI-to-CV, Theremin, Light-to-CV, analogue sequencer) with attenuator. The control input has polarizing function, i.e. the manually adjusted dividing factor can be modulated upwards or downwards. The basic idea of a polarizer is described in the modules A-133 Voltage Controlled Polarizer and A-138c Polarizing Mixer.

The output waveform is rectangle with 50% duty cycle. Unlike the A-115 with fixed dividing factors (2, 4, 8, 16) the dividing factor of the A-163 is voltage controlled and can be any integer value between 1 and about 20 (but only one output). In contrast to A-113 the dividing factor of the A-163 is voltage controlled and the output waveform is rectangle (the A-113 has 4 sawtooth outputs with 4 adjustable but not voltage controlled dividers).
Read more
 1 in stock $77.81
Cat: 577765 Rel: 10 Sep 19
 
Frequency divider for clock, trigger & gate signals - 4HP
Notes: Module A-160 is a frequency divider for clock/trigger/gate signals, designed to be a source of lower frequencies, particularly for rhythm uses. The Trigger input will take clock signals from, e.g. an LFO, MIDI sync, or the gate from a MIDI-CV interface.

At the outputs, you have access to the sub-divided clock signals, from half the clock frequency down to 1/64. The low/high levels of the output signals are 0V and about +10V.

The A-160 also has a reset input. Whenever a reset signal is sensed, all outputs are set to zero, until the reset voltage disappears.

The Clock Divider can be used in combination with the A-161 Clock Sequencer to produce stepped sequences with a length of from one to eight events.
Read more
 1 in stock $71.31
Cat: 577759 Rel: 10 Sep 19
 
Additional 4HP module for the A-160
Notes: Module A-161 is an eight-step Clock Sequencer which is internally connected to the Clock Divider (A-160). Eight outputs are sequentially switched by the clock signals from the A-160 (see Fig. 1) and can act, for instance, as sequential rhythmic triggers for an envelope. The reset on the A-160 also works on the A-161 (instant return to Step 1). The low/high levels of the output signals are 0V and about +10V. In combination with a mixer (A-138) short analogue sequences can be generated. Our MIDI-Analog-Sequencer MAQ16/3 is suitable for MIDI-controlled analogue sequences up to 48 steps. A "real" analogue sequencer with 8 steps is the A-155.
Read more
 1 in stock $63.75
Cat: 745777 Rel: 10 Sep 19
 
Expansion module to the A-149-1
Notes: A-149-2 is an extension module for A-149-1. It makes available 8 digital random voltages (i.e. only low/high states like a gate signal). The outputs are controlled by the "Quantized Random Voltages" section of the assigned A-149-1 and correspond to the 8 digital outputs of the shift register that is used to generate the Quantized Random Voltages. As the alteration of the A-149-2 outputs is clock controlled by the Clk In of the "Quantized Random Voltages" section of the A-149-1 the A-149-2 can be used to create random rhythmical sequences.

The A-149-2 requires the A-149-1 and has to be mounted directly to the left or right of the A-149-1 as an internal ribbon cable connection has to be established between A-149-1 and A-149-2.
Read more
 1 in stock $56.19
Cat: 745790 Rel: 10 Sep 19
 
8HP dual trigger delay for Eurorack
Notes: Module A-162 contains two identical circuits that generate a trigger signal with adjustable delay and length from an incoming rectangle signal (e.g. gate, trigger, rectangle output of an LFO or VCO). The rising edge of the incoming signal is used to trigger the new trigger signal. This module makes it possible to delay the onset of a trigger pulse, and also change its length.

On each of the two units, two controls can alter the onset time and duration of triggers, from about 2 ms up to more than 10 seconds. A control LED shows the generated signal.
Read more
 2 in stock $63.75
Cat: 719648 Rel: 02 Sep 19
 
Master I/O module
Notes: The MASTER module is the base of every AE modular system - it contains;

- The voltage regulation (5V) for the power supply of the modules
- MIDI input (minijack; Breakout cable to DIN-5 socket is available separately)
- In/out-sockets (3.5mm minijack) for audio out and/or interfacing with a Eurorack system
- All bus signals (CV, GATE, CTRL, MIDI clock/start/stop) as patch sockets

The power supply is a 9V DC adapter; it can be connected either at the side or on the top of the module.
Read more
 2 in stock $59.43
Cat: 719652 Rel: 02 Sep 19
 
4-track, 16-step trigger sequencer
Notes: TRIQ164 is a 4-track, 16-step trigger sequencer.

Four track buttons select the track to be edited; with 16 buttons each step of the track can be activated an is then displayed by an LED.

For each step in each track a "repeat" can be activated, resulting in repeated triggers within one step. The number of repeats can be selected from one to eight by the REPEAT knob. Additionally, the repeat count can be CV controlled by the REPEAT CV input.

The inputs MUTE 1/2 allow to mute the outputs 1 and 2 by an external signal (e.g. for muting a kick drum)

Each of the 16 steps has a separate trigger output for additional control for certain steps or limiting the sequence length by connecting one of the outputs to the RESET input.

Use it for any kind of rhythmical patterns, typically for triggering drum sounds or envelope generator!

No, it has no pattern load/save features; this will be part of a future, much more complex sequencer. TRIQ164 is designed as improved replacement for the STEP10.

Width: 2U
Read more
 3 in stock $54.02
Cat: 719650 Rel: 03 Sep 19
 
Analogue 16-step CV sequencer
Notes: The SEQ16 is a 16-step sequencer for controlling oscillator pitch and triggering envelopes.

Compared to "classic" analogue sequencers it works a bit different: Instead of setting the CV for each step independently (which means in fact "tuning" each step which can be a bit tedious), the SEQ16 has 5 knobs for pre-setting different CV's (= notes); each of the 16 step knobs selects one of these CVs, plus 0V (=base note) plus Pause (no trigger output). So some CVs have to be fine-tuned once; with the step knobs you can focus entirely on the sequence itself and you can even modify it on the fly, still remaining in tune.

An additional feature is "accent"; this can be set for each step by turning the knob fully clockwise. If a step is set to "accent", a separate trigger output is set and also a gate repeat for the regular gate output can be selected (from one to eight repeats).
Read more
 2 in stock $89.68
Cat: 732847 Rel: 22 Jul 19
 
LFO + highly stable S&H in one module
Notes: Erica Pico LFO/S&H is a full analogue modulations source - LFO and Sample and Hold - to provide some controlled randomness to your modular setup.
Read more
 4 in stock $90.78
Cat: 738520 Rel: 22 Jul 19
 
3 channel mixer - 3HP
Notes: Pico Mixer is simple 3 channel DC coupled mixer intended to mix AUDIO SIGNALS AND CV SIGNALS in order to obtain complex modulations. Also it may serve as CV AND AUDIO attenuator.
Read more
 1 in stock $61.59
Cat: 732845 Rel: 22 Jul 19
 
Simple 2-4 step sequencer - 3HP
Notes: Pico SEQ2 is a straight-forward, full analogue 4 step sequencer/waveshaper with adjustable sequence length. If you want to have a simple, compact stepped modulation source in your setup, then this is it! Particularly interesting use of the Pico SEQ2 is waveshaping - just apply any audio source to the CLK IN, tweak the knobs and be amazed!
Read more
 2 in stock $94.01
Cat: 739138 Rel: 16 Jul 19
 
Voltages expander for Permutation - silver faceplate, 6HP
Notes: Variant is an expander module based on the original Voltages expander for the Turing Machine. Variant adds two additional bipolar CV outputs (with modulation inputs) that are derived from Permutation's gate sequence.
Read more
 1 in stock $90.77
Cat: 738640 Rel: 09 Jul 19
 
Voltage controlled sine-LFO with four separate, phase shifted outputs - 8HP
Notes: Module A-143-9 is a derivative of our planned thru-zero quadrature VCO. It is a voltage controlled sine LFO with 4 outputs. The phase shift between the outputs is 90 degrees. The sine shifted by 90 degrees is also called cosine, the sine shifted by 180 degrees is nothing but the inverted sine, and the sine by 90 degrees is nothing but the inverted cosine.

The frequency range is from some minutes to frequencies beyond audio with three ranges selected by a toggle switch:

- Switch position H: about 30 Hz ... 3.5 kHz with the manual frequency control ("Frq."), beyond 20 kHz with additional external CV
- Switch position M: about 1 Hz ... 150 Hz with the manual frequency control ("Frq.")
- Switch position L: about 0,1 Hz ... 10 Hz with the manual frequency control ("Frq."), down to several minutes with additional external CV

Two exponential frequency control inputs are available: CV1 without attenuator and CV2 with polarizer. Consequently the module can be used even as an experimental sine VCO but does not feature an exact 1V/oct CV input! The precision CV input will be left to the thru-zero quadrature VCO.

Two LEDs display the positive and negative share of the sine output.

The core of the module is a so-called quadrature circuit that generates a sine a cosine signal with very low distortion. The quality of the sine/cosine signals are much better than those generated by a waveform converter with a sawtooth or triangle signal as starting point.

The output levels are about 5 Vss (+/-2.5V) but can be adjusted internally by a trimming potentiometer (P5 "Shape").

Typical applications:

- External sine/cosine oscillator for the frequency shifter A-126
- Modulations with pure sine/cosine waveforms
- Quadrature/barberpole effects (e.g. with the voltage controlled mixer A-135)
- Experimental sine/cosine VCO (e.g. for FM sounds)

Many users suggested to add a common output level control, i.e. four VCAs with one common control (manual + CV without attenuator + CV with polarizer) for the output levels. This is why we also designed the Quad VCA module A-132-2 with the possibility of an internal default connection to the four outputs of the A-143-9 (no soldering required, short 10 pin flat cable with removable connectors on both ends).

The A-143-9 is also a meaningful addition for the Frequency Shifter module A-126. It enables frequency shifting even below 50 Hz generating e.g. these mellow beat sounds with a few Hz frequency shifting only. The following document describes how to connect the A-126 and the A-143-9: A126_A143_connection.pdf.

The thru zero version of the A-143-9 with temperature compensation is the module A-110-4.
Read more
 1 in stock $78.88
Cat: 577763 Rel: 10 Jul 19
 
8HP Eurorack module featuring two identical VCA's
Notes: Module A-132-3 is composed of two identical voltage controlled amplifiers (VCA). Each VCA has a manual gain control and a control voltage input with attenuator. The character of the control scale can be switched to linear or exponential. All inputs and outputs are DC coupled. Consequently, the VCA's can be used to process both audio and control voltages. The input has no attenuator available but is capable to process up to 16Vss signals (i.e. -8V...+8V) without distortion.
Read more
 1 in stock $99.41
Cat: 738632 Rel: 09 Jul 19
 
Quad Decay featuring four simple envelope generators - 8HP
Notes: Module A-142-4 contains four simple envelope generators. The only time parameter is Decay and can be adjusted manually by means of the Dec. control in the range 2 ms ... 2 seconds. The attack time can be adjusted internally by means of a separate trimming potentiometer for each sub-unit in the range 1 ms ... 15 ms. The factory setting is about 3 ms. This is the attack time of the TB303. Each envelope output has a LED control available. The trigger inputs are normalled (1 -> 2 -> 3 -> 4).

Suggestions for modifications:

Each sub-unit has a pin header with two pins available. When the two pins are shortened (e.g. by means of a jumper or a toggle switch connected to the two pins) the corresponding sub-unit changes to a loop mode. In this mode the unit is triggered by itself like an LFO..

By changing the value of a capacitor the time range can be modified (e.g. 0.2 ms ... 0.2 seconds or 20 ms ... 20 seconds)
Read more
 1 in stock $96.17
Cat: 738616 Rel: 10 Jul 19
 
Stereo headphone amplifier - 6HP
Notes: The A-139-2 is a headphone amplifier module with two mono inputs and a stereo headphone output. It can be used for driving small loudspeakers, LED strips, small magnets etc.

- Two-channel headphone amplifier
- Two audio inputs with level controls
- Input 1 is normalled to Input 2
- Common loudness/master level control
- Headphone output (stereo 1/4" jack socket)
- Max. output power ~ 2 W per channel (@ 8 Ohm load)
- DC coupled inputs and outputs (i.e. also useful for other applications like small loudspeakers, lamps, LEDs, magnets, motors - provided that the power is sufficient)
Read more
 1 in stock $52.94
Cat: 738645 Rel: 10 Jul 19
 
Low frequency oscillator with adjustable waveform - 8HP
Notes: Module A-146 (LFO 2) is a Low Frequency Oscillator, which produces periodic control voltages over a wide range of frequencies.

The LFO can be used as a modulation source for a series of modules (for instance pulse width and/or frequency modulation of a VCO, modulation of a VCF cut-off frequency, amplitude modulation with a VCA).

Three outputs are available, with different waveforms: sawtooth / triangle; square wave, and positive-voltage square wave.

The waveform is continuously adjustable from rising sawtooth, through triangle to falling sawtooth. The same control affects the pulse width of the square wave.

A three-way switch can select one of three frequency ranges, spanning from one cycle every few minutes, at the lowest, up to audio frequency at the highest.
Read more
 1 in stock $66.99
Cat: 738621 Rel: 10 Jul 19
 
Voltage controlled envelope generator with decay parameter - 8HP
Notes: Module A-142-1 is a voltage controlled envelope generator. The only time parameter is decay (like TB303). Decay may be adjusted manually and via voltage control input (with attenuator). The envelope output is displayed with LED control. Additionally from the envelope signal a Gate signal and an inverse Gate signal with adjustable threshold is derived. LED control for Gate output. Thus one obtains a voltage controlled Gate additionally or alternatively to the envelope signal with voltage controlled duration.

The attack time is fixed to about 0.2 ms, the shortest decay time is about 2 ms. By changing the value of a capacitor the shortest time can be modified (details can be found here: A100_Capacitors.htm).

Typical applications: dynamic control of decay e.g. in combination with the Analog/Trigger Sequencer A-155, voltage controlled trigger delay functions (like A-162, but voltage controlled).
Read more
 1 in stock $79.96
Cat: 577791 Rel: 10 Jul 19
 
VCA with exponential response for low level sensitivity - 8HP
Notes: Module A-131 provides voltage-controlled amplification. For audio signals, you would normally use the exponential VCA (A-131), and for control voltages, the linear VCA (A-130). It doesn't always have to be that way, though.

The amount of amplification the VCA's provide is determined by the voltage at the CV input, and the position of the gain control, which sets the overall gain in the system.

The VCA has two audio inputs, each with an attenuator. They are amplified by an amount determined by the combination of the gain and the two CV controls.
Read more
 1 in stock $74.56
150/196(ページ1/4)の商品
1  2  3  4  »

Filter

Synth modules
DJ機器
Release Date
Close