安全なお買い物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全なお買い物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Synth modules

View:
Options
117/17(ページ1/1)の商品
Subscribe to our weekly Studio Equipment emails
FORTHCOMING
4ms Listen Up Passive Expander Module For Listen Modules
coming soon $65.98
FORTHCOMING
Doepfer A-170 Dual Slew Limiter Module
Cat: 751699 Rel: 23 Oct 19
 
Two separate slew limiters for generating portamento effects - 8HP
Notes: Module A-170 contains two separate slew limiters, also known as portamento controllers or integrators. The first SL has just one joint control, which sets both rise and fall times (c. 0 ...10 sec). The second SL has separate controls for rise and fall times, and can therefore be used as a simple AR envelope generator. Over and above this, you can set the overall range for these parameters, with a three-position switch, as on the full ADSRs.

Both slew limiters have two LEDs each, to show the state of the rising and falling voltages.


Additional technical remarks: If the upper slew limiter is used for precision applications (e.g. portamento/glide of one or more VCOs) a buffer (e.g. A-185-1 or A-185-2) is recommended between the A-170 output and the VCO(s) input(s). The reason is a small voltage drop that is caused by the protection resistor at the A-170 output. An A-185-1 or A-185-2 connected between the A-170 and the VCO(s) avoids that voltage loss. For all A-170 manufactured later than May 2009 (recognizable by the label "Version 2" on the pc board) this remark is not valid as these modules are equipped with an additional voltage buffer at the output.

The lower slew limiter cannot be used for precision applications because of the voltage loss caused by the diodes of the circuit.
Read more
coming soon $62.74
FORTHCOMING
Doepfer A-170v Dual Slew Limiter Module (vintage edition)
Cat: 751702 Rel: 23 Oct 19
 
Two separate slew limiters for generating portamento effects - 8HP
Notes: Module A-170 contains two separate slew limiters, also known as portamento controllers or integrators. The first SL has just one joint control, which sets both rise and fall times (c. 0 ...10 sec). The second SL has separate controls for rise and fall times, and can therefore be used as a simple AR envelope generator. Over and above this, you can set the overall range for these parameters, with a three-position switch, as on the full ADSRs.

Both slew limiters have two LEDs each, to show the state of the rising and falling voltages.


Additional technical remarks: If the upper slew limiter is used for precision applications (e.g. portamento/glide of one or more VCOs) a buffer (e.g. A-185-1 or A-185-2) is recommended between the A-170 output and the VCO(s) input(s). The reason is a small voltage drop that is caused by the protection resistor at the A-170 output. An A-185-1 or A-185-2 connected between the A-170 and the VCO(s) avoids that voltage loss. For all A-170 manufactured later than May 2009 (recognizable by the label "Version 2" on the pc board) this remark is not valid as these modules are equipped with an additional voltage buffer at the output.

The lower slew limiter cannot be used for precision applications because of the voltage loss caused by the diodes of the circuit.
Read more
coming soon $77.89
FORTHCOMING
Doepfer A-172 Maximum/Minimum Selector & Rectifier Module
Cat: 751706 Rel: 23 Oct 19
 
Module for processing/mixing of control voltages - 4HP
Notes: A-172 is a minimum/maximum selector module and is equipped with four analogue inputs and two analogue outputs (minimum, maximum). The main application of the module is the processing/mixing of control voltages, e.g. random voltages, ADSR, LFO, S&H, ribbon CV, theremin-CV and similar, but even for audio signal processing the module can be used (e.g. several outputs of the same or different VCOs).

The module permanently picks the maximum resp. minimum voltage out of the four input signals and outputs these voltages to the maximum resp. minimum jack socket.

To adjust offset and amplitude for each input independently (i.e. to bring the signal into the right "position" with the desired level) we recommend combining the module with the A-129-3 Slew Limiter/Attenuator/Offset Generator (see patch example below). The other sketch below shows the basic principle of the max/min module by means of three sine waves (e.g. three LFOs) with different frequencies and different levels.

The module can be used also as a simple half-wave rectifier.
Read more
coming soon $51.11
FORTHCOMING
Doepfer A-174-2 Modulation Wheels CV Source Module
Cat: 751707 Rel: 23 Oct 19
 
Modulation wheel module with two wheels - 14HP
Notes: A-174-2 is a modulation wheel module with two wheels. The factory setting is a spring loaded wheel at the left side with bipolar voltage output (i.e. 0V in centre position, positive voltage in the upper range, negative voltage in the lower range, voltage range about -5.5 V ... 0V ... +5.5 V) and a wheel without spring at the right side with positive voltage output (i.e. 0V in the lowest position and positive voltage when operated, voltage range about 0...+8 V). For the spring loaded wheel a voltage "plateau" around 0 V is preset (jumper) so that the output voltage is 0 V in a small area near the centre position.

By means of jumpers the factory settings can be changed. For each wheel two jumpers are available: one for the voltage range (positive or bipolar) and one for the voltage plateau around 0 V. If these settings are changed even the wheels have to be re-adjusted mechanically. Therefore, such modifications should be carried out by a qualified person only. By request the module is available from the factory even with two wheels both with or without springs (additional charges Euro 10.00 for each change).

Important note for module mounting: As the potentiometer of the left wheel projects about 10 mm the rim of the front panel a 2 or 4 HP blind panel has to be mounted left from the module - unless the module left to the A-174-1 has sufficient space in this area (e.g. A-174-1).
Read more
coming soon $77.89
FORTHCOMING
Doepfer A-175 Dual Voltage Inverter Module
Cat: 751709 Rel: 23 Oct 19
 
Two identical inverters - 4HP
Notes: Module A-175 (Dual Voltage Inverter) is exactly what it says it is: two identical inverters, which will take a voltage and output it in an inverted form - so that an input of +5 V will be output as -5 V, an input of -2 V will be output as +2 V, and so on. Two LEDs give a visual indication of the (positive or negative) output signal.
Read more
coming soon $53.01
FORTHCOMING
Doepfer A-176 Control Voltage Source Module
Cat: 751711 Rel: 23 Oct 19
 
Three independent voltage sources - 8HP
Notes: Module A-176 (Control Voltage Source) provides three voltage sources, to use wherever an extra CV is required. The top two voltage sources (CV 1 and CV 2) have controls for coarse and fine control of the voltage output; the third source (CV 3) just has the one control.

The range of the voltages output can be preset, either to 0 to +5 V or to -2.5 V to +2.5 V depending on your likely requirements. There is a jumper on the circuit board for each of the three voltage sources.

A typical use for the module would be to provide fine as well as coarse tuning for an A-110 standard VCO, (which, unlike the A-111, only has one tune control).

In general, this module will be useful whenever you need a manually controllable CV on a module which doesn't itself have a built-in control.
Read more
coming soon $62.74
FORTHCOMING
Doepfer A-177-2 External Foot Controller II Module
Cat: 751715 Rel: 23 Oct 19
 
Foot controller interface - 8HP
Notes: Economically priced module for connecting one foot controller and one double foot switch for control A-100 functions by means of the feet. For example, the frequency of a filter or the loudness can be controlled by a foot controller, but even other parameters like LFO frequency, modulation depth, phasing, pitch or any other voltage controlled parameter. The gate outputs controlled by the double foot switch can be used e.g. to trigger an envelope generator or to start/stop a sequencer. Even a single foot switch can be used if only one gate signal is required.

A special application of the A-177-2 is the usage within a Trautonium replica. The foot switches can be used to switch the mixtures of the subharmonic oscillator A-113. The foot controller can be used to control the overall loudness in combination with a VCA.

A-177 is compatible with the foot controllers FP5 and double foot switch VFP2. The Foot controller and double foot switch are not included with the module. If you want to use another foot controller or foot switch it has to be compatible to FP5 or VFP2.

If the foot controller FP5 is used the CV output range is about 0...+8V. The gate output levels are 0/+12V in combination with the VFP2 (foot switch not operated = 0V, foot switch operated = +12V).
Read more
coming soon $53.01
FORTHCOMING
Doepfer A-178 Theremin Control Voltage Source Module
Cat: 751716 Rel: 23 Oct 19
 
Theremin controller module - 8HP
Notes: Theremin module for generating a variable control voltage by approaching/removing hand to/from an antenna. The distance range is about 30-40 cm. Additionally the module is equipped with a Gate output with adjustable threshold level. Controls/Inputs/Outputs: antenna input, offset (knob for zero adjust), 2 x CV out, 2 x LED (for CV control positive/negative and zero offset adjust).

To simulate the original Theremin two A-178, a VCO (e.g. A-110) and a linear VCA (e.g. A-130 or A-132) are required. But of course the A-178 can be used to control other functions in the A-100 (e.g. filter frequency, modulation depth and/or speed, tempo, attack/decay time and so on).

The CV output voltage of the A-178 can range - according to the setting of the front panel controls - from -10V...+10V. The gate output switches from 0V to about +10V.

Applications:

- Controlling any voltage controlled parameter of the A-100, e.g. pitch or pulsewidth (VCO A-110), loudness (VCA A-130/131/132), panorama (A-134), filter frequency or resonance (A-120/121/122/123), phasing (A-125), frequency shift (A-126), resonance peaks (A-127), envelope parameters (A-141/142), tempo (A-147)

- Triggering of A-100 activities via gate with adjustable threshold, e.g. starting an envelope (A-140/141/142), Start/Stop of a sequence (A-155), any switching function (A-150/151)

- Conversion into MIDI control change messages is possible with the A-192.

If two or more A-178 are used the distance between the modules/antennas should be at least 40-50 cm. Otherwise the antennas may affect each other.
Read more
coming soon $96.28
FORTHCOMING
Doepfer A-182-1 Switched Multiples Module
Cat: 751724 Rel: 23 Oct 19
 
Eurorack passive multi-connector - 6HP
Notes: Module A-182-1 is a simple passive multi-connector similar to the multiples modules A-180-1/A-180-2. In contrast to modules A-180-1/2 each socket is equipped with a 3-position switch that allows to connect the corresponding socket to the internal bus #1 (left position), bus #2 (right position) or to turn the socket off (centre position).

Examples:

- All switches in left position or all switches in right position: 8-fold multiple

- Four switches in left position and four switches in right position: two 4-fold multiple

- X switches in left position, Y switches in right position and Z switches in centre position: two separate multiples with some sockets turned off
Read more
coming soon $53.01
FORTHCOMING
Doepfer A-184-1 Ring Modulator, Sample & Hold, Track & Hold, & Slew Limiter Module
Cat: 751756 Rel: 23 Oct 19
 
4HP Eurorack module featuring a combination of 3 functions
Notes: Module A-184-1 is the combination of three functions:

- Ring Modulator
- Sample&Hold/Track&Hold unit
- Slew Limiter

The same functions are actually already available in other modules (e.g. A-114, A-148, A-170). But in many systems it's not necessary to have two ring modulators (A-114) or two S&H units (A-148) or two slew limiters (A-170) available. That's why we have compiled these function in one small 4 HP module.

The upper section is nothing but half of an A-114, i.e. a ring modulator with the usual X/Y inputs and the X*Y output. Inputs and outputs of this sub-unit are AC coupled, i.e. suitable only for audio signals. A detailed explanation of a ring modulator can be found on the A-114 info page.

The lower section is a Sample & Hold (S&H) / Track & Hold (T&H) unit (same as half of an A-148) followed by a slew limiter (same as the upper section the A-170). A toggle switch is used to set the mode to S&H or T&H. In S&H mode the unit picks out a sample from the voltage at the SH input at the rising edge of the trigger signal input. In T&H mode the output follows the input voltage as long as the level of the trigger signal is high. As soon as the trigger signal turns low, the last voltage is stored. The trigger input is internally normalled to high, i.e. the unit works just as a slew limiter in T&H mode when no trigger signal is applied.
Read more
coming soon $96.28
FORTHCOMING
Doepfer A-184-2 Voltage Controlled Crossfader & Triangle To Sine Waveshaper Module
Cat: 751758 Rel: 23 Oct 19
 
Sine converter/VC crossfader - 4HP
Notes: Module A-184-2 is the combination of two functions and planned primarily as an expansion module for VCOs or LFOs (e.g. A-110-1, A-110-2, A-145, A-147-2).

Triangle-to-Sine Waveshaper:

The upper section is a very precise triangle-to-sine converter (thanks to Tim Stinchcombe who recommended this circuit). It can be used to convert any triangle waveform into a (nearly) perfect sine. The converter is much better than the simple diode converter used in the A-110-1, A-111-1, A-145 and A-147-2. Two trimming potentiometers are used to optimize the sine shape. The converter should be assigned to one VCO or LFO because the trimming potentiometers have to be re-adjusted if the input level or DC offset of the input signal changes. If the trimming potentiometers are deliberately mis-adjusted it can be used also as a waveshaper for non-sine waveforms (e.g. sine-shaped at the top of the signal and a peak at the bottom, even voltage controlled by applying an additional voltage to the waveshaping circuit, "circuit-bending" notes will be available).

The waveform converter is DC coupled and can be used also for low frequencies (e.g. LFO triangle waves).

Voltage Controlled Crossfader:

The lower section is a voltage controlled crossfader. It has two inputs A and B. The two signals are mixed together with variable percentage. When the manual control CF is fully CCW only signal A appears at the CF Out socket. When the manual control CF is fully CW only signal B appears at the CF Out socket. In the centre position of the manual control both signal appear with the same level. In addition a control voltage input CV with attenuator is available to enable voltage control of the crossfade.

Two LEDs display the crossfading shares of input A and B.

The crossfader uses two high quality VCAs (SSM2164). Inputs and outputs are DC coupled. Consequently it can be used for audio signals and slowly varying control voltages as well.

The sockets of the upper section (triangle and sine) are normalled to the inputs A and B of the crossfader section. That way the crossfader is used to fade between triangle and sine of the VCO or LFO connected to the waveshaper. If other signals are plugged into the input sockets A and B these signals are used for crossfading.

The main application is to fade between two different waveforms of a VCO or LFO or two different VCF outputs. But the module can be used for any other signals too as the waveshaper and crossfader sections are independent apart from the normalled sockets.
Read more
coming soon $81.67
FORTHCOMING
Doepfer A-185-1 Active Bus Access Module
Cat: 751760 Rel: 23 Oct 19
 
Provides input & output access to your Eurorack's internal CV/Gate bus
Notes: Active bus access module to feed CV and Gate into the A-100 bus (e.g. when using more than one frame or with external CV/Gate interfaces). Miniature jack sockets for CV In, Gate In, 2xCV Out, 2xGate Out, 2 LEDs for CV/Gate control

In general, the A-185 is recommended as soon as more than 2 VCO's (A-110, A-111) are controlled by the same control voltage source. Without interconnection of the A-185 in this case tuning inaccuracies (scale) may occur. The A-185 is mounted close to the VCOs. The controlling voltage for all VCOs is applied to the CV In socket of the A-185. By means of the CV line of the bus board the CV is connected to all VCOs at the same bus board.
Read more
coming soon $53.01
FORTHCOMING
Doepfer A-185-2 Precision Control Voltage Adder & Buffer Module
Cat: 751763 Rel: 23 Oct 19
 
Precision adder (mixer) and buffer for control voltages - 6HP
Notes: Module A-185-2 is a precision control voltage adder/buffer. Precision means that the amplification of the inputs without attenuators is exactly 1.00 and is suitable to add control voltages for the pitch control of VCOs (e.g. from keyboard + sequencer 1 + sequencer 2). Summing resistors matched to 0.1% are used to obtain an accuracy of 0.1% for the added voltages.

The module is equipped with four CV inputs: one with attenuator and three without attenuator. Each input is normalled to +1 V (i.e. if no plug is inserted the input contributes 1 V to the sum appearing at the output).

The input with attenuator can be used for common modulations (e.g. from an LFO, ADSR, Theremin, Pitch-Bender) for all VCOs connected to the output. The Lev.1 control is used to adjust the depth of the modulation, the first switch selects the polarity of the modulation. If no signal is connected to the first socket the attenuator works as a (fine) tuning knob because a voltage in the range 0...+1V (right position of the switch) or 0...-1V (left position of the switch) is added to the CV output.

The inputs without attenuators are planned to add control voltages coming out of keyboards, sequencers, Midi-to-CV interfaces, ribbon controllers or other CV sources that follow the 1V/oct standard. For example the CV of a keyboard can be used to transpose the CV coming from a sequencer, or the CV of a slow sequencer can be used to transpose the CV from a fast sequencer.

Each input is equipped with a three-position switch that determines if the corresponding voltage is added (right position), subtracted (left position) or if the input has no effect (centre position). If no plug is inserted the corresponding switch works as an octave switch for the lower three sections as the default 1 V are added or subtracted to the output voltage according to the switch position. The first switch can be used to add a variable voltage to the sum output. The variable voltage is adjusted with the Lev.1 control and the knob works then as kind of a (fine) tuning control.

The module is equipped with 4 outputs: three non-inverting and one inverting ouput. An internal jumper can be used to connect the non-inverted or inverted output to the CV line of the A-100 bus. That way the module can used to control several VCOs that are connected to the same bus board as the A-185-2 (same functionality as A-185-1).
Read more
coming soon $72.48
FORTHCOMING
Doepfer A-185-2v Precision Control Voltage Adder & Buffer Module (vintage edition)
Cat: 751764 Rel: 23 Oct 19
 
Precision adder (mixer) and buffer for control voltages - 6HP
Notes: Module A-185-2 is a precision control voltage adder/buffer. Precision means that the amplification of the inputs without attenuators is exactly 1.00 and is suitable to add control voltages for the pitch control of VCOs (e.g. from keyboard + sequencer 1 + sequencer 2). Summing resistors matched to 0.1% are used to obtain an accuracy of 0.1% for the added voltages.

The module is equipped with four CV inputs: one with attenuator and three without attenuator. Each input is normalled to +1 V (i.e. if no plug is inserted the input contributes 1 V to the sum appearing at the output).

The input with attenuator can be used for common modulations (e.g. from an LFO, ADSR, Theremin, Pitch-Bender) for all VCOs connected to the output. The Lev.1 control is used to adjust the depth of the modulation, the first switch selects the polarity of the modulation. If no signal is connected to the first socket the attenuator works as a (fine) tuning knob because a voltage in the range 0...+1V (right position of the switch) or 0...-1V (left position of the switch) is added to the CV output.

The inputs without attenuators are planned to add control voltages coming out of keyboards, sequencers, Midi-to-CV interfaces, ribbon controllers or other CV sources that follow the 1V/oct standard. For example the CV of a keyboard can be used to transpose the CV coming from a sequencer, or the CV of a slow sequencer can be used to transpose the CV from a fast sequencer.

Each input is equipped with a three-position switch that determines if the corresponding voltage is added (right position), subtracted (left position) or if the input has no effect (centre position). If no plug is inserted the corresponding switch works as an octave switch for the lower three sections as the default 1 V are added or subtracted to the output voltage according to the switch position. The first switch can be used to add a variable voltage to the sum output. The variable voltage is adjusted with the Lev.1 control and the knob works then as kind of a (fine) tuning control.

The module is equipped with 4 outputs: three non-inverting and one inverting ouput. An internal jumper can be used to connect the non-inverted or inverted output to the CV line of the A-100 bus. That way the module can used to control several VCOs that are connected to the same bus board as the A-185-2 (same functionality as A-185-1).
Read more
coming soon $80.05
FORTHCOMING
Intelijel FSR 1U Module
Cat: 747522
coming soon $80.05
FORTHCOMING
Intellijel Duatt 1U Module
Cat: 747516
coming soon $75.71
117/17(ページ1/1)の商品

Filter

Synth modules
DJ機器
Release Date
Featured
Close