Synth modules

Notes: ***B-STOCK: Box opened, product in perfect working order***


ADSR is a four stage linear envelope with two expressive ranges. Each stage can be modified independently allowing for the creation of complex, multi-segment envelopes. Great for modulating filters, VCAs, and oscillators.

Notes: ***B-STOCK: Without original box, product has light surface marks but otherwise in perfect working condition.***


ADSR is a four stage linear envelope with two expressive ranges. Each stage can be modified independently allowing for the creation of complex, multi-segment envelopes. Great for modulating filters, VCAs, and oscillators.

Notes: ***B-STOCK: Without original box, product has light surface marks but otherwise in perfect working condition.***


Clk is a voltage controlled clock generator with all the features a master clock needs. It has an extremely wide range from ten seconds between pulses well into audio rate. In addition, the pause button and CV input provide an expressive feature that is all too often missing in a modular setup. Stop using LFOs or other modulation sources for your master clock, and let Clk do what it's best at.

Notes: The CVADDER-HQ is a precision adder especially for adding 1V/octave (pitch-controlling) CVs. This makes it possible e.g. to transpose a sequence. Compared to general purpose CV mixers (like POLAMIX), this module does the summing of the CVs very precise (within a few millivolts), so the desired pitch is not affected.

The module offers four CV inputs where three of them are summed, and the CV at the fourth input is subtracted - meaning "transposition downwards".

This module also allows transposing the incoming CV by one or two octaves or a variable offset by buttons.

A separate output provides the voltage of the internal transposition (+1, +2 octaves / free).

If the transposition buttons are not necessary and you prefer to have a dual precision adder, take a look at the 2CVADD-HQ module.

Notes: A simple VC panner with CV-controlled level. The left input normals to the right input to give an easy way to add panning to a mono signal.

Expandable

Bartender, Barbacks, DVCA, Cast Iron, Mingles, and USB-2CH can all be connected with Dupont cables (aka female to female breadboard cables) via pin headers on the back of the modules. Connecting the in and out pins will send/receive the audio into the next module.

Width: 4hp
12V: 40mA
-12V: 40mA

Notes: Two channel USB module.

Standard Mode - Send two channels into your USB device and receive two channels from USB.

Insert Mode - Send two channels to your USB device and get a copy of the sent signal in the outputs.

Toggle between the modes via a pair of jumpers on the back. The USB-B to USB-A cable is provided with the module. Why use the cutting edge USB-B? I felt the jacks were way more sturdy than mounting USB-C jacks vertically.

Expandable - Bartender, Barbacks, DVCA, Cast Iron, Mingles, and USB-2CH can all be connected with Dupont cables (aka female to female breadboard cables) via pin headers on the back of the modules. Connecting the in and out pins will send/receive the audio into the next module.

Width: 4HP
12V: 10mA
-12V: 10mA

Notes: Module A-130-2v is composed of two identical voltage controlled amplifiers (VCA). Each VCA has a manual gain control (also named Initial Gain) and a control voltage input with attenuator. The character of the control scale can be switched to linear or exponential. All inputs and outputs are DC coupled. Consequently the VCAs can be used to process both audio and control voltages (e.g. for voltage control of the level of LFO or envelope signals). The signal input has no attenuator available but is capable to process up to 16Vpp signals (i.e. -8V...+8V) without distortion. For the processing of higher levels an external attenuator (e.g. A-183-1) is recommended.

The amplification range is 0...1. Even with a higher external control voltage the amplification remains at 1 (kind of "amplification clipping" at 1).

Controls (for each of both units):

Gain: manual gain control (Initial Gain) in the range 0...1
CV: attenuator for the CV input
lin/exp: switches the VCA characteristic to linear or exponential, in center position the VCA is off (mute function)
Inputs and outputs (for each of both units):

CV: control voltage input, min. +5V required for max. amplification (1) with CV control fully CW and Gain fully CCW
In: signal input, max. 16Vpp (+8V...-8V) without distortion
Out: signal output

A-130-2v is the slim version of module A-132-3 and offers essentially the same features. But the distances between the controls are smaller and rubberized small-sized knobs are used. In return the front panel has 4 HP only which is half the width of the A-132-3. The module is primarily planned for applications where only limited space is available.

Power consumption: 30mA at +12V and 30mA at -12V

Depth: 50mm

HP : 4

Notes: Module A-130-4 contains four linear VCAs with a common level control section for all four VCAs. It can be used for all applications of simultaneous amplitude/level control of up to four different audio or CV signals. A-130-4 is the replacement of the no longer available module A-132-2. Compared to the A-132-2 the width has been reduced from 8HP to 4HP.

The module has these controls and in/outputs available:

Control Man.: manual control of the amplification
Control CV: attenuator for the control voltage applied to socket CVo socket Input 1
Sockets In 1...4: VCA inputs 1...4
Sockets Out 1...4: VCA outputs 1...4

Application examples:

simultaneous amplitude/level control of up to four different audio or CV signals
polyphonic application 1: simultaneous control of the frequency modulation depth of 4 VCOs (Quad-LFO A-145-4 or Quad-VCLFO A-147-5 > A-130-4 > FM inputs A-111-4)
polyphonic application 2: simultaneous control of the pulsewidth modulation depth of 4 VCOs (Quad-LFO A-145-4 or Quad-VCLFO A-147-5 > A-130-4 > PWM inputs A-111-4)
simultaneous control of quadrophonic signals

Technical notes:

The maximum amplification for each VCA is about 1 ("Man." control fully CW). Even with an external control voltage applied to the CV input the maximum amplification is limited to 1.
The module is equipped with two internal connectors (pin headers with 4 pins each). Pin header #1 can be used to normalize the four inputs to other modules (e.g. Quad LFO A-145-4 or A-147-5, Quad ADSR A-143-2). Pin header #2 can be used to connect the four outputs to other modules.
The max. level at the VCA inputs without clipping/distortion is about 20Vpp or +/-10V.

Dimensions
4 HP
45 mm deep

Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


A-138s is a simple but useful 4-in-2 mixing tool. It has four inputs available. Each input is equipped with an attenuator (Level) and a panning control that is used to distribute the signal to the left and right output. Beyond stereo mixing it is equally suited to create variable parallel routings. For example: Any of the four inputs may be routed in variable intensity to feed two filters.

You may regard the A-138s as a smaller version of the A-138m Matrix Mixer.

Inputs and outputs are DC coupled, i.e. the module can be used for the mixing of control signals too.

- 3U Eurorack module, 8 HP wide, 30 mm in depth
- Power consumption: 10 mA at +12 V and 10 mA at -12 V

Notes: Module A-147-5 contains four voltage controlled low frequency oscillators (VCLFO) with triangle waveform outputs. All LFOs share a common frequency control. Each of the LFOs 2, 3 features a Delta control which is used to shift the frequency of the LFO in question up or down. With the Delta controls at center positions the frequencies of all LFOs are roughly the same. To control the frequencies by external control voltages four CV inputs are available which follow roughly the 1V/oct standard.

The module has these controls and in/outputs available:

Control F: manual control of the frequency for all four LFOs
Control Delta F2, F3 and F4: manual control of the frequency shift up/down for the LFO in question
Sockets CV 1...4: Frequency control voltage inputs (normalled from top to bottom)
Sockets with triangle symbol 1...4: triangle outputs
LEDs: visual displays of the triangle outputs (red = positive, yellow = negative output voltage)

Application examples:

Generation of four triangle modulation signals with a common frequency control for all LFOs and individual controls for the frequency deviation of each LFO, manually adjustable and controllable by external control voltages
Generation of modulation signals for polyphonic FM/PWM applications. For this the four CV inputs are connected to the same control voltages which are used to control the frequencies of the corresponding VCOs. That way each LFO follows the frequency of the associated VCO with the possibility to control the frequency of all VCOs (control F) and the frequency deviations (Delta F controls). For the simultaneous modulation depth control the Quad VCA module A-130-4 is recommended.
Generation of complex modulation signals by summing up the outputs (e.g. by means of a mixer module A-138n / A-138i / A-138j)

Technical notes:

The level of the triangle outputs is about +/-5V (10Vpp)
The manually adjustable frequency ranges from about 0.025 Hz (about 40 seconds) to about 50 Hz with the delta controls of LFOs 2, 3 and 4 about center position
The frequency deviations adjusted by the delta controls are about +/-1:5. Example: with 1 Hz in center position the frequency shift ranges from about 0.2 Hz in position -5 to about 5 Hz in position +5 (1 Hz/5 = 0.2 Hz, 1 Hz*5 = 5 Hz).
The manual frequency controls and the control voltage inputs have an exponential control behavior
With external control voltage the max. frequency is about 150 Hz, the minimum frequency
The scale of the CV inputs is roughly 1V/oct (not adjustable)
The CV inputs are normalled from top to bottom. Provided that only socket CV1 is patched CV1 controls the frequencies of all four LFOs.
When each CV input is patched to it's own control voltage each LFO is controlled individually by it's own CV. In this case CV1 controls only the frequency of LFO1.
Internally the rectangle outputs are available at four terminals (typ level +/-10V or 20Vpp). If required they can be wired to four sockets of a DIY breakout module made by the user, 1k protection resistors are recommended to avoid short circuits. If lower levels are required passive attenuators (voltage dividers) may be used.
Internally is even an (unbufferd) triangle sum signal available. For this each of the four triangle outputs is simply connected to the sum output terminal via a 47k resistor. This output has high impedance and should be buffered or amplified to avoid level drop when the load changes (e.g. by means of an A-180-3 or A-180-4 or A-183-3).
By changing the values of the capacitors in the LFO circuits even other frequency ranges are possible (e.g. Quad VCO to form kind of a cloud VCO). Pay attention that the accuracy of the CV input scales is not sufficient for precise 1V/oct VCO applications. The 1V/Oct scales cannot be adjusted and the circuits are not temperature compensated.

Dimensions
4 HP
45 mm deep

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Module A-147-5 contains four voltage controlled low frequency oscillators (VCLFO) with triangle waveform outputs. All LFOs share a common frequency control. Each of the LFOs 2, 3 features a Delta control which is used to shift the frequency of the LFO in question up or down. With the Delta controls at center positions the frequencies of all LFOs are roughly the same. To control the frequencies by external control voltages four CV inputs are available which follow roughly the 1V/oct standard.

The module has these controls and in/outputs available:

Control F: manual control of the frequency for all four LFOs
Control Delta F2, F3 and F4: manual control of the frequency shift up/down for the LFO in question
Sockets CV 1...4: Frequency control voltage inputs (normalled from top to bottom)
Sockets with triangle symbol 1...4: triangle outputs
LEDs: visual displays of the triangle outputs (red = positive, yellow = negative output voltage)

Application examples:

Generation of four triangle modulation signals with a common frequency control for all LFOs and individual controls for the frequency deviation of each LFO, manually adjustable and controllable by external control voltages
Generation of modulation signals for polyphonic FM/PWM applications. For this the four CV inputs are connected to the same control voltages which are used to control the frequencies of the corresponding VCOs. That way each LFO follows the frequency of the associated VCO with the possibility to control the frequency of all VCOs (control F) and the frequency deviations (Delta F controls). For the simultaneous modulation depth control the Quad VCA module A-130-4 is recommended.
Generation of complex modulation signals by summing up the outputs (e.g. by means of a mixer module A-138n / A-138i / A-138j)

Technical notes:

The level of the triangle outputs is about +/-5V (10Vpp)
The manually adjustable frequency ranges from about 0.025 Hz (about 40 seconds) to about 50 Hz with the delta controls of LFOs 2, 3 and 4 about center position
The frequency deviations adjusted by the delta controls are about +/-1:5. Example: with 1 Hz in center position the frequency shift ranges from about 0.2 Hz in position -5 to about 5 Hz in position +5 (1 Hz/5 = 0.2 Hz, 1 Hz*5 = 5 Hz).
The manual frequency controls and the control voltage inputs have an exponential control behavior
With external control voltage the max. frequency is about 150 Hz, the minimum frequency
The scale of the CV inputs is roughly 1V/oct (not adjustable)
The CV inputs are normalled from top to bottom. Provided that only socket CV1 is patched CV1 controls the frequencies of all four LFOs.
When each CV input is patched to it's own control voltage each LFO is controlled individually by it's own CV. In this case CV1 controls only the frequency of LFO1.
Internally the rectangle outputs are available at four terminals (typ level +/-10V or 20Vpp). If required they can be wired to four sockets of a DIY breakout module made by the user, 1k protection resistors are recommended to avoid short circuits. If lower levels are required passive attenuators (voltage dividers) may be used.
Internally is even an (unbufferd) triangle sum signal available. For this each of the four triangle outputs is simply connected to the sum output terminal via a 47k resistor. This output has high impedance and should be buffered or amplified to avoid level drop when the load changes (e.g. by means of an A-180-3 or A-180-4 or A-183-3).
By changing the values of the capacitors in the LFO circuits even other frequency ranges are possible (e.g. Quad VCO to form kind of a cloud VCO). Pay attention that the accuracy of the CV input scales is not sufficient for precise 1V/oct VCO applications. The 1V/Oct scales cannot be adjusted and the circuits are not temperature compensated.

Dimensions
4 HP
45 mm deep

Notes: ***B-STOCK: Box damaged, product in perfect working order***


Module A-196 contains a so-called phase locked loop (PLL). The basic PLL system is shown in the sketch at the bottom of this page. A PLL consists of three parts: voltage-controlled oscillator (VCO), phase comparator (PC), and low-pass filter (LPF). All parts are normally connected to form a closed-loop frequency-feedback system.

This is how a PLL works: The output of the internal VCO (linear CV control, rectangle output) is compared with an external signal (e.g. the rectangle output of a A-110 VCO) in the so-called phase comparator (PC). The output of the phase comparator is a digital signal (low/high/tristate) that indicates if the frequency resp. phase difference of the two input signals is negative, zero or positive. The output of the phase comparator is processed by a low pass filter (LPF) to generate a smooth voltage that is used to control the frequency of the internal VCO. The 3 units VCO, PC and LPF form a feedback loop that works like this: The control voltage (output of the LPF) increases as long as the external frequency is higher than the frequency of the internal VCO und stops increasing when both frequencies become identical. The control voltage decreases as long as the external frequency is lower than the frequency of the internal VCO und stops decreasing when both frequencies become identical.

But there are some stumbling blocks: Different types of phase comparators with advantages and disadvantages can be made. Some phase comparators e.g. even lock at harmonics, i.e. if the two frequencies to be compared are integer multiples. But for some applications this can be used to create interesting effects. The A-196 contains 3 different types of phase comparators: PC1 is a simple exclusive OR, that even locks at harmonics. PC2 is a so-called RS flipflop and PC3 a more complex digital memory network. The user can select one of the three phase comparators with a 3-position switch. When PC2 is used a LED displays the "locked" state, i.e. when the frequency of the internal VCO is identical to the external frequency.

Special attention has to be directed to the frequency of the LPF. To obtain a smooth control voltage for the VCO the frequency of the LPF has to be much smaller than the lowest frequency of the internal or external audio signal. Otherwise the frequency of the internal VCO will jitter or wobble around the correct frequency. But for special effects this frequency jitter can be used intentionally. Example: frequencies in the range 50Hz...1kHz have to be processed with the PLL. Therefore the frequency of the LPF has to be about 10Hz or even less. Such a low frequency of the LPF causes a noticeable slew of the internal VCO. When the frequency of the external signal jumps e.g. between 500Hz and 1kHz it takes about 0.1 second until the internal VCO reaches the new frequency (like portamento). So one has to find a compromise between frequency jitter and portamento. But these remarks are valid only for the "ideal" working PLL. As the A-196 is used in a musical environment the "problems" and disadvantages with jitter and slew time lead to additional musical applications like portamento effects, wobbling frequencies or harmonic locking according to the type of frequency comparator and time constant of the PLL low pass filter. Instead of the internal manually controlled low pass filter the voltage controlled slew limiter A-171 can be used to obtain voltage control of this parameter. Normal audio filters (e.g. A-120, A-121) cannot be used for this job as the minimum frequency is to high (down to a few Hz or even less necessary) and the signal has to be DC coupled due to the low frequencies. Audio filters are normally AC coupled.

Another very important application of a PLL is frequency multiplication in combination with an external frequency divider. For this the output of the PLL-VCO is processed through an external frequency divider (e.g. A-163, A-160, A-161, A-115) before it is fed to In1 of the phase comparator. In this case the frequency of the PLL-VCO will be a multiple of the master frequency. E.g. if the A-163 is used and adjusted to dividing factor 5 the frequency of the PLL-VCO will be 5 times the frequency of the master VCO. Consequently, frequency division (A-163) leads to frequency multiplication with the PLL circuit. In combination with the PLL low pass frequency several effects can be realized (frequency multiplication with portamento or wobbling). The frequency multiplication can even be used to drive a graphic VCO. If your graphic VCO e.g. has 8 steps (e.g. A-155) and you use a frequency divider with factor 8 in the PLL feedback the output of the graphic VCO has the same frequency as the master VCO. Another application is the generation of pseudo-harmonics (not real harmonics as only rectangle waves are available) or clock generation for switched-capacitor filters.

Notes: ***B-STOCK: Without original box, product in perfect working order***


Pico BBD is surprisingly great sounding (we were surprised ourselves), full analogue 4092 stage bucket brigade delay module; the smallest BBD in Eurorack. Besides nice and clean flanger and delay effects, at full CW settings of TIME and feedback knobs it can produce extreme sonic artefacts. Tweak knobs and enjoy!

Notes: This is an envelope follower based on a classic module from the seventies but with some improvements to suit modern needs.

The IN signal is bifurcated to the envelope follower circuit and also to a THRU output, so the original signal is also available for external processing.

The envelope follower has three controls, a switch to select response time (fast, medium, slow), a pot to adjust GATE threshold and a pot to adjust the envelope CV level.

This little module will help you shape the timbre and/or the level envelopes of your sounds. From dynamic envelope filtering to compressor like side chaining there are lots of possibilities to mangle your audio.

Tech specs:

- 4HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 18mA , -12V 16mA

Notes: As the name suggests this module can produce sub frequencies of -1 and -2 octaves relative to the square wave signal provided at the input jack.

But this is not just a simple SUB generator. It also has a little mixer that will let you add different levels of -1 and -2 octave signals to the original square wave. You can select the -2 octave signal to be a square wave or a pulse wave.

The module has individual outputs for the mixed signal, the -1 octave and the -2 octave.

This little modules can produce enough timbral variation to make you bass sound exciting.

Tech specs:

- 4HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 12mA , -12V 9mA

Notes: Arcade performance buttons for gating and actuating.

You can use Asteroids in two different ways:

Gate generator using the two outputs. A 5V gate will be output when the relevant button in pressed.

Momentary manual actuator. Whatever is present at the relevant input will be output when the button is pressed.

Product Specifications

12V draw: 7mA
-12V draw: 0mA
5V draw: 0mA
Depth: 25mm
Width: 8HP

Notes: 3xMIA is a 6-channel attenuverting mixer/offset/scale/polarizer

3 blocks of 2-channel attenuverting mixers, using dual concentric pots. Each channel can be switched to mix with the subsequent channel, allowing for 2-2-2, 4-2, 6 mix configurations.

With nothing plugged into an input, an offset is normalled to that channel. The inner knobs control the A inputs, while the outer knobs control the B inputs.

DC coupled, so it can be used for audio, CV, or both at the same time.

80 mA +12V
80 mA -12V
35 mm Depth
24HP wide

Notes: 3xMIA is a 6-channel attenuverting mixer/offset/scale/polarizer

3 blocks of 2-channel attenuverting mixers, using dual concentric pots. Each channel can be switched to mix with the subsequent channel, allowing for 2-2-2, 4-2, 6 mix configurations.

With nothing plugged into an input, an offset is normalled to that channel. The inner knobs control the A inputs, while the outer knobs control the B inputs.

DC coupled, so it can be used for audio, CV, or both at the same time.

80 mA +12V
80 mA -12V
35 mm Depth
24HP wide

Notes: Turn that frown upside down - or make that negative waveform positive. Or vice versa! The Herzlich 180 Invert will shift the phase of any four signals you put in by 180 degrees, effectively inverting them.

This has countless applications: fix phase errors in your mix, turn a low pass signal into a high pass, cancel out unwanted signals, change the behaviour of an LFO or gate, there are countless situations and applications where inverters are incredibly useful.

You'll be happy to own an inverter in any system - but why own just one when you get four here? Add a useful tool to your system today, with the 180 Invert.

Dimensions: 2 HP

Notes: You've got triggers, gates, clocks and other such binary signals that you want to mix - but you'd much prefer if they did not interact and interrupt each other!

What you need is OR logic - and this passive OR logic in 2hp makes it easy to mix up to four signals in one, and even allows you to switch any off the signals on or off at will. Your trigger sequencing will become truly next level.

The ABCD/OR: It's the logical choice.

Notes: Take care of your utility mixing needs with the Dual Active Mixer, a dual active averaging mixer in 2hp that functions as either two 3-to-1 and a 6-to-1 averaging mixer, letting you mix audio and CV in a highly efficient package.

No knobs and no buttons, just pure mixing joy to help you sort out your patches with no wasted space. Not much else to say about this tiny wonder of technology, except to say it does what it says.

Money well spent thanks to Herzlich Labs, once again.

Dimensions: 2 HP

Notes: You want less sound, and you want it fast. You want a mute that doesn't take up any power, a mute that doesn't take up a lot of space, and a mute that accepts three signals. You want a mute that's nice and clicky, and a mute that doesn't cost an arm and a leg.

You've found it.

Dimensions
2 HP

Current Draw
Module does not draw current

Notes: The simple, but mighty, buffered multiple in beautiful black and gold. You know you want it, you want to get REAL buff, and this mult will get you there and a bit further still.

Built by hand by a lapsed office worker turned electronics engineer by night, you will certainly feel the hopeful spirit of this device as you install it in your rack.

The buffered multiple is useful when multiplying voltages that are sensitive to changes, such as volt-per-octave applications, and situations where you need to create a buffer between modules. This can come in handy more often than you might think.

The time for words is over, now is the time for action. Purchasing action. Go ahead, you know you need this.

Notes: Fade between two signals with the fader, just as nature intended

Do you have aspirations to smoothly fade between two signals? The Herzlich Crossfade lets you do exactly that, and exactly nothing else, using well-designed active circuitry and a smooth and performance friendly sliding potentiometer.

Whatever your aspirations are, this crossfader lets you live out your crossfading dreams in the simplest possible way, with not a fraction of an inch wasted on unnecessary features. Only delightful build quality and pleasantly smooth crossfading lies ahead for you.

Dimensions: 2 HP

Notes: This is based on the classic passive LPG, but with the utmost care taken to hand-craft the ideal version of this device.

With WIMA capacitors, custom built vactrols and exceptional little details like an LED window to get visual feedback on your CV input, the Herzlich Labs Dual Low Pass Gate is the final word in the realm of classic, passive LPGs. Every detail has been cared for, down to high-end hardware and switches to round out the experience, all in a narrow 2hp without any compromises made with respect to the form factor.

Many designs, components and iterations were rejected, so Herzlich could could bring you this - the LPG boasts two identical channels, with three cutoff settings per channel. The middle setting will behave like a VCA, while the left and right settings will have the familiar LPG sound. Care has been taken to reduce bleed, but as it is a classic passive VCA, some small amounts of audible bleed can be expected from the circuit.

Each Dual Low Pass Gate is built by hand and personally tested, to assure the high quality of these units. You can feel confident that exceptional care has been taken to bring you the most exceptional passive LPG experience possible, with the Herzlich Dual Low Pass Gate.

Dimensions: 2 HP

Notes: Dual Full Wave Rectification for Fun and Profit

Are you sick and tired of having pesky negative waveforms interfering with your signals? Do you detest seeing the back-and-forth motion of AC waveforms going backwards, then forwards? Those days are OVER with the Herzlich Labs FWR, a dual full-wave rectifier that puts an end to negative waveforms!

When you plug a signal into the FWR, you get two outputs in return, which have fully rectified the input. All negative inputs will be kindly returned to you in pristine, fully positive form. Beautiful bouncy sine waves, turned into pure "Oops! All Positive Waveshapes"-cereal, just the way you like it.

Use it anywhere where you want ONLY positive vibes, or use it with an inverter to get ONLY negative signals, if you please. Yes, you get two of these functions in just 2hp!

Dimensions: 2 HP

Notes: Two bipolar LEDs allow you to visualize your voltages as they swing between positive and negative, as well as their level of intensity, without affecting the signal you input.

Think of it as a 1D oscilloscope in just 2hp! An easy way to grasp what your patch is currently doing, without sacrificing the money or space on more fully-fledged solutions. Useful as part of a patch to keep track of your oscillations, as a troubleshooting device to quickly verify that something is doing what it should be doing, or simply as a healthy dose of blinkenlights in addition to your existing array of sparkling LED pleasures. Best of all? You get two in just 2hp - you'll have to spend some serious cash to get that kind of function-per-hp density anywhere else!

Dimensions: 2 HP

Notes: Bartender? The power of gate signals at the touch of a button, please - but make mine a narrow one!

You already know what this is: it's a gate signal generator, and it generates gate signals. That's all there is to it. You press the button, the LED indicator lights up, and you get a 5v gate signal! Brilliant!

You get three, in just 2hp! That's 1 1/2 gate signal generators per hp! That's more than [competing product] from [competing brand]! You knew you made a good decision when you decided to look at this product.

All that remains now is to open your heart, and your wallet. Buy this gate generator - this version is the latching model (stays on or off after pressing). In fact, it works really well with the Quad Gate to Trigger Converter, also from Herzlich Labs - now you can generate both gates and triggers with ease! And in such little hp!

Oh, one more thing? Your friends are going to be very envious of this, when you show it off. Gold plated nuts, gold plated front panel, tastefully matte indicator LEDs, pleasantly tactile buttons, black hardware. All the details have received the closest care and attention.

Dimensions: 2 HP

Notes: Bartender? The power of gate signals at the touch of a button, please - but make mine a narrow one!

You already know what this is: it's a gate signal generator, and it generates gate signals. That's all there is to it. You press the button, the LED indicator lights up, and you get a 5v gate signal! Brilliant!

You get three, in just 2hp! That's 1 1/2 gate signal generators per hp! That's more than [competing product] from [competing brand]! You knew you made a good decision when you decided to look at this product.

All that remains now is to open your heart, and your wallet. Buy this gate generator - this is the momentary model (is normally off, and temporarily on when you press it). In fact, this also works really well with the Quad Gate to Trigger Converter, also from Herzlich Labs - now you can generate both gates and triggers with ease! And in such little hp!

Oh, one more thing? Your friends are going to be very envious of this, when you show it off. Gold plated nuts, gold plated front panel, tastefully matte indicator LEDs, pleasantly tactile buttons, black hardware. All the details have received the closest care and attention.

Dimensions: 2 HP

Notes: Aren't you tired of pulling and plugging your patches all day when testing out how something sounds? Does this sound better than that? Effects on or off? Should this signal even be here?

The Micro FXBP is a performance mute, FX send/return and A/B input selector all in one. Easily test and audition different input signals, with and without effects, or just turn the whole thing off for some peace and quiet. And in just 2hp! That's incredible!

What's it gonna be; tugging on your little patch cables all day, or pressing a few handy buttons?

Notes: You may have lots of very quiet sounds. Instrument level sounds, bit sniffer sounds, inductor coil sounds, sounds that are barely even there. We're talking electric guitars, piezos, contact microphones, pickups, anything you'd classify as a hi-z input - but Eurorack is loud! Eurorack signals are smoking hot! So how will you ever get the flimsy signal from your electric guitar into the glory of Eurorack hotness territory?

The solution is easy, with the Micro Hi-Z preamp from Herzlich, you can crank that guitar all the way from amplification and into overdrive. Take your little piezo and get a good, strong signal out of it, or grab your preferred contact mic and get some sounds you never could have even dreamed of into your Eurorack, in just 2hp! That's almost as much as 1hp, which is nearly 0hp, which is no space at all. That's incredible!

Got large, adult-sized human hands? No problem! Instead of a wobbly, shaky rotary potentiometer (bad, no good) the engineers and scientists at Herzlich Labs opted to install a vertical slide pot to control gain instead (good, very nice). Controlling your gain is smooth and easy, but the truth is seldom pure and never simple, except this one time where it is.

Go ahead, spend all that other hp you free up by buying the 2hp Hi-Z Preamp on some other stuff that will come in handy in your music production. It also works with an electric bass guitar as well as with electric guitars.

Notes: Mix it up with the Micro Mix, a dual passive mixer in 2hp that functions as both a 3-to-1 and a 6-to-1 passive mixer, allowing you to perform acts of minor sorcery in your modular system (or maybe outside with your Volca and Pocket Operator jam?).

Nothing knobs or buttons here to confuse you, plug in either audio, CV, clock or triggers, and get the mixed signal out. The best part? Since it's passive, there's no guarantee what you put in is exactly what you'll get out. Embrace the unpredictable world of passive mixing like they did in the 60s and 70s.

Notes: Drawing inspiration from the MMI Maxima, the MMI Helios is intended as a middle ground between the gestural control surface of the Maxima and the fingertip control of the smaller MMI.

Less density, but a much higher degree of patch control is the key point of the Helios, which complements other MMI devices very well, and can be joined with other Helios (Helii?) to form larger and creative control surfaces.

The design is greatly simplified compared to the original MMI, with only two I/O jacks - either can function as input and output, and their interaction with each other is determined by touching both plates simultaneously to form a connection, or in cooperation with other MMI devices.

Available in a "right" and "left" version - one is an exact mirror image of the other, which makes it suitable for having two units adjacent to one another.

Dimensions: 8 HP

***Please note: the "righthand" version is not included, it is shown in the picture for demonstration purposes only. ***

Notes: Drawing inspiration from the MMI Maxima, the MMI Helios is intended as a middle ground between the gestural control surface of the Maxima and the fingertip control of the smaller MMI.

Less density, but a much higher degree of patch control is the key point of the Helios, which complements other MMI devices very well, and can be joined with other Helios (Helii?) to form larger and creative control surfaces.

The design is greatly simplified compared to the original MMI, with only two I/O jacks - either can function as input and output, and their interaction with each other is determined by touching both plates simultaneously to form a connection, or in cooperation with other MMI devices.

Available in a "right" and "left" version - one is an exact mirror image of the other, which makes it suitable for having two units adjacent to one another.

Dimensions
8 HP

Notes: The Herzlich Man Machine Interface - a beloved instrument, but what if there was even more of it? An MMI with more than one dimension? An MMI arranged in a manner of... matrix?

With operation identical to it's little brother, the MMI Matrix allows the user to patch inputs to outputs by connecting zig-zagged patterns together with fingers, fruits, cables, pizza slices or any other conductive source. The labyrinth patterns will immediately connect the zig-zags immediately adjacent, whether above and below, or on each side. Furthermore, the two labyrinths within labyrinths will connect ALL adjacent inputs and outputs, which may lead to beautiful disasters or otherworldly insights.

As with its predecessor, the MMI Matrix is fully touch and pressure sensitive, reacting to the amount of pressure exerted, the amount of skin connecting, and the resistive quality of your body. Incredibly easy to perform with, the MMI Matrix offers new and far more advanced ways to patch your performances, whether CV, triggers or audio signals. Create reverb swells that vary between different types of reverb, use multiple fingers and labyrinth patterns to mix trigger signals into complex polyrhythms or create beautiful chords by combining various pitch inputs with a chord oscillator. The MMI Matrix also integrates very well with it's little brother, so there is absolutely no need to hold back!

Oh, and as always, it uses NO power! But it will take up 10hp of space in your system. A fair deal!

Dimensions
10 HP
14 mm deep

Current Draw
Module does not draw current

Notes: The Om is a slim, passive 2hp LPG with characterful resonance. Taking notes from its bigger brother, the Omen, the Om offers similarly beautiful resonant LPG action in half the size and skiff-friendly depth.

In a convergence of old-school LPG design and more modern components, the Om boasts a single -6dB resonant filter, custom hand-built vactrol and no less than three cutoff modes designed to inspire your next sounds.

Although the little brother of the Omen, the Om brings a distinct sound to the table. Do not mistake the Om for an Omen sawn in half, as they will both provide musically interesting and useful sounds to your setup.

Exactly as with the Omen, care has been taken to create a circuit with near-zero audio bleed and the best possible characteristics for a passive LPG. Of course, many of the natural features of vactrols remain, such as subtle memory effect when engaging the vactrol for long periods.

Finally, you receive maximum blinkenlights as an LED on the front panel simulates the action of the vactrol, so you'll always know what's going on under the hood. No collection of fancy LPG's is complete without the Om(en)!

Notes: You've been plugging, patching and sweeping for hours, when it hits you: you're not actually listening to what you're making. Up until this point, the sad reality of modular has been that your ears won't hear the sweet sounds of your music, unless you invest in a bloated, oversized output module or a professional mixer. This ends now.

The Herzlich Micro Phone Out is an active headphone output in only 2hp - and it includes a very pleasantly tactile volume slider! Gone are the days where you would have to spend untold hp on useful and clean headphone outputs, now all that remains is beautiful, small simplicity.

No stereo signals to process? No problem. The left channel automatically works as a mono input with nothing plugged into the right channel. Forget everything else - this is the one and only output module you'll need!

Dimensions
2 HP
34 mm deep

Notes: In recent years, stereo signal paths have increasingly found their way into the wonderful world of Eurorack synthesis - so naturally, utilities should follow suit. Introducing the Herzlich PSA, a simple solution to a problem you might not even realize you had. Far from just useful as an attenuator for audio sources in mixdowns, the PSA can also be used to bring audio down to more managable levels (such as line level), attenuate multiple signals simultaneously (like increasing the modulation depth of two LFO's at the same time! It's like having two hands, but with one hand!) and even function as a multiple: Attenuator 1 is normalled to Attenuator 2, so multing your stereo signal (or two mono signals) while attenuating the two signals individually is easy as pie.

There's not much else to say, except that it's passive, and draws no power - and it looks great!

Dimensions
4 HP

Current Draw
Module does not draw current

Notes: Let's talk about filters - not your usual, souped up, CV controlled stereo-enabled monstrosity, but just regular old filters for EQ'ing and smaller filtering duties. That's this, right here - but in stereo, with a wide range and with a highly useful slide pot.

What's it useful for? Any task where you'd like to user a filter, but sacrificing an entire filter module might be overkill. Submixing and cutting out the highs of a signal, feedback, amplifying the lows in a bass drum, tone control - there are many reasons you would want a passive low pass filter. Two, even! Either one for your left and right input, or one for two different but linked mono inputs. Neat!

This filter is fully passive, only 2hp and skiff friendly with a very shallow installation depth. It's also particularly good looking in black and gold.

Notes: Let's talk about filters - not your usual, souped up, CV controlled stereo-enabled monstrosity, but just regular old filters for EQ'ing and smaller filtering duties. That's this, right here - but in stereo, with a wide range and with a highly useful slide pot.

What's it useful for? Any task where you'd like to user a filter, but sacrificing an entire filter module might be overkill. Submixing and cutting out the highs of a signal, feedback, amplifying the lows in a bass drum, tone control - there are many reasons you would want a passive low pass filter. Two, even! Either one for your left and right input, or one for two different but linked mono inputs. Neat!

This filter is fully passive, only 2hp and skiff friendly with a very shallow installation depth. It's also particularly good looking in black and gold.

Notes: Beauty. Refinement. Attenuversion.

It's another Herzlich Labs release: the 2hp stereo Attenuverter. Two channels of connected attenuversion, allowing you to fully and smoothly invert any signals you plug in - turn negative to positive, turn phase to antiphase, and find all the variations in between.

With the usual pleasantly tactile sliding pot, the sAttenuverter is both performance friendly and inspiring to use. Extremely suitable for linked mono signals and stereo alike, it will feel right at home in the increasingly popular stereo setups in modular.

Dimension: 2 HP

Notes: Need an offset voltage? Of course you do, you probably need one all the time, and you can never seem to find one. Well, here's two.

Yes, the Stereo Offset boasts not one but TWO linked offset voltages, and even better, they can be independently set as unipolar or bipolar with jumpers on the back of the module. To further aid your adventure in offsetting, bicolor LEDs will indicate the current state of both outputs.

Smoothly transition between voltages to simultaneously control other functions in your system, either by applying identical voltages to two different places, or by using simultaneous unipolar and bipolar signals for advanced control over your Eurorack system.

Do the right thing - get an offset generator you will love.

Dimensions: 2 HP

Notes: Switchy is a module that allows you to turn on or off up to three modules (or busboard) independently of each other.

No need to turn off the whole case: All three voltages (+12V, -12V, 5V) are interrupted at the same time.

Used to reduce the background noise of certain "noisy" digital modules when not in use, to initialize certain modules or change their function, to change an SD card, to relieve the power supply with energy-consuming modules, etc.

Dimensions
6 HP
30 mm deep

Current Draw
20 mA +12V
20 mA -12V
20 mA 5V

Notes: Tilt is the first in Laine's series of core modules, which will take cues from the main product line and strip back the features so both the module width and cost can be shrunk dramatically.

Comprising an 'Ambler' style tilt EQ network similar to the 'Stilts' topology, Tilt allows simultaneous cut and boost of low and high frequencies using a single control.

Tilt control circuits are known for the transparency of their cut and boost curves, coupled with the inherent emphasis gained from cutting one end of the frequency spectrum whilst boosting at the opposite end.

It sounds pretty good on all audio source material but is especially suited to tracking drums, guitar and lead, or manipulating effects sends and returns.

With the control knob at 12o'clock the sound passed is neutral. Turning the control knob clockwise will boost high and cut low frequencies pivoting from a fixed mid-range point. Turning the control anti-clockwise below 12 o clock will in turn boost low frequencies and cut the highs.

In addition to the EQ there is a soft clipping network which will begin to saturate signals over 15 volts peak to peak.

Tilt uses the same high quality OPA op amps, Alpha pots and ENIG PCBs as found in our main product line.

Features

Compact EQ tilt control in 1U
Soft clipping network
High-quality components used throughout

Specifications

Intellijel 1U format
Width 8HP
Depth 28mm
Power requirements ~10mA +12V/~10mA -12V
Impedance Input 100k / Output 1k

Notes: Tilt is the first in Laine's series of core modules, which will take cues from the main product line and strip back the features so both the module width and cost can be shrunk dramatically.

Comprising an 'Ambler' style tilt EQ network similar to the 'Stilts' topology, Tilt allows simultaneous cut and boost of low and high frequencies using a single control.

Tilt control circuits are known for the transparency of their cut and boost curves, coupled with the inherent emphasis gained from cutting one end of the frequency spectrum whilst boosting at the opposite end.

It sounds pretty good on all audio source material but is especially suited to tracking drums, guitar and lead, or manipulating effects sends and returns.

With the control knob at 12o'clock the sound passed is neutral. Turning the control knob clockwise will boost high and cut low frequencies pivoting from a fixed mid-range point. Turning the control anti-clockwise below 12 o clock will in turn boost low frequencies and cut the highs.

In addition to the EQ there is a soft clipping network which will begin to saturate signals over 15 volts peak to peak.

Tilt uses the same high quality OPA op amps, Alpha pots and ENIG PCBs as found in Laine's main product line.

Features

Compact EQ tilt control in 1U
Soft clipping network
High-quality components used throughout

Specifications

Intellijel 1U format
Width 8HP
Depth 28mm
Power requirements ~10mA +12V/~10mA -12V
Impedance Input 100k / Output 1k

Notes: Uni is a triple attenuverter utility module designed to give cases gigantic macro control knobs.

Inputs:

CV inputs 1 and 3 - CV input for bidirectional attenuation. When input cables aren't plugged into these jacks, 5v reference signals will be used.
CV input 2 - CV input for either unidirectional or bidirectional attenuation. When an input cable isn't plugged into this jack, a 5v reference signal will be used.
Switch - toggles CV input 2 between unidirectional and bidirectional attenuation.

Outputs:

CV outputs 1, 2 and 3 - attenuated CV output. If no cables are plugged into an output jack, it is summed into the subsequent output jack.

25 mA +12V 20 mA -12V 0 mA 5V
10 HP 27mm deep

Notes: The 6MUTE module is made for click-free muting of up to 6 audio channels. For each channel, a high quality button mutes and unmutes the corresponding channel. The button is illuminated, so you get a visual feedback about the mute-state of each channel.

The signal is not simply cut off hard for muting, but faded out in a very short time to avoid clicks and pops. So it is perfectly suitable for live usage, too!

Dimensions
1 U

Current Draw
8 mA 5V

Notes: The classic ADSR envelope with CV control for all parameters

The ADSR module offers the classic four-stage envelope (Attack, Decay, Sustain, Release) that is not only loopable (patch the end output into gate input) but also accepts CV control over each of the stages! For the time values (A, D, R) the value set by the knob can be increased to five times the duration by the corresponding CV value. For the Sustain value the knob and CV value are simply added.

Notes: The CVSHIFTER module is the AE version of the well-known analogue shift register modules that are around in the modular world since a long time. It works like this: The CV input is sampled with each trigger input signal and this CV is sent to the CV 1 output; at the same time, all CV outputs 1-4 are shifted by one.

Compared to the "classic" circuits, this module is digital based and therefore doesn't suffer from drift as some analogue ASRs and S&Hs do. The result is, that you can e.g. control the pitch of up to four oscillators which is a first step into polyphony.

The CVSHIFTER module offers three modes:

Classic: Each trigger shifts the CV outs by one position, the new CV goes to output CV 1
Cycle: Each trigger sends the CV to the next output channel, restarting at out 1; additionally a gate signal at the according output.
Random: The CVs are sent in random order to one of the four outputs, plus a gate at the according output.

Notes: The DIODEFILTER is an adaption of the well-known diode ladder filter that became most popular by Roland's TB-303 bassline. And here it is for the AE modular!