安全なお買い物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全なお買い物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Synth modules

View:
Options
17/7(ページ1/1)の商品
Subscribe to our weekly Studio Equipment emails
MFB
Cat: 695619 Rel: 16 Sep 19
 
Analogue 24db lowpass filter - 8HP
Notes: The 24dB VCF SSI is a voltage controlled analogue low pass filter module with the new SSI2144 chip. In addition, it has a 12dB output that works either as a low pass or bandpass (+/- 12dB). There are two inputs, one with attenuator. Another CV input with attenuator is available for the cut-off frequency. The resonance is controlled either via a controller or via another CV input with attenuator.

The power consumption is +/- 30 mA. The module has a width of 8 HP (40 mm).
Read more
 2 in stock $73.57
MFB
Cat: 695604 Rel: 16 Sep 19
 
MFB-522/Tanzbar style analogue bass drum module
Notes: The Bass-522 module is based on the 522 circuit and offers a punchy attack, long decay and wider pitch range. Adjustable noise and pitch envelope have also been added.

The sound can be triggered by Gate, M-Bus and signals like piezo pickups, dynamic mics and drum pads. The Sense parameter decides the sensibility and dynamic of attack, amplitude. decay and pitch.

The following parameters are available and can be controlled by CV:

TONE dampens the attack transient.
DECAY sets the release time of the amplitude.
TUNE defines the basic pitch from around 35 to 70 Hz.
PITCH controls the amount of pitch envelope.
NOISE mixes the noise floor (no CV control).

The module offers the new developed M-Bus connector which means you can you control everything via MIDI/CV interface or the new MFB SEQ-01 Pro Drum Sequencer without additional patching. The following addresses are supported:

Trigger with Velocity - MIDI Note #35 or #36 (switchable) and controller values for Tone, Decay, Tube, Pitch and Noise Decay.

The module has a width of 8HP (40mm).
Read more
 4 in stock $85.48
MFB
Cat: 695607 Rel: 16 Sep 19
 
Clap module based on circuit designs of the MFB-522 & Tanzbar Lite
Notes: The Clap-522 Modul contains an enhanced circuit of the MFB-522 and Tanzbar Lite. You can edit and modulate the sound in a wide range.

As modular concept you have the possibility to control the parameter PUSE, SNAP, ATTACK, DECAY and FILTER via CV-signals from Envelopes, LFOs and Step Sequencers.

The parameters are in detail:

PULSE is the amount of claps between 1 and 7.
ATTACK sets the noise level between the clap repetitions.
DECAY controls the release of the noisy reverb.
FILTER defines the colour of the noise floor.
WIDE edits the gap between the single claps.

Beside sequencer generated analogue and digital trigger-signals, drum pads, piezo pickups and dynamic mics may also be used. Here the SENS controls allow individual adjustment of the input sensitivity. Dynamic trigger also changes the volume of the clap.

The module provides the new developed M-Bus connection. MIDI signals can control following destinations:

Trigger MIDI Note #39 or #82, switchable, with Velocity. Controller values for Wide, Attack, Decay and Filter.

The module has a width of 8 HP (40mm).
Read more
 1 in stock $94.14
MFB
Cat: 695610 Rel: 16 Sep 19
 
Stereo drum mixer - 12HP
Notes: The DRUM-99 module is an audio-mixer that has been designed for the modules of the MFB-DRUM series but also for usage with other manufacturer's modules. When using multiple drum-modules in a modular system, the following processing stages like filters or VCAs often lack enough audio inputs. To route a complete drum-set through a filter, a separate mixer like the DRUM-99 comes handy.

DRUM-99 offers five monaural inputs with individual level control. Tiny trim-controls are used to set the channel panorama position for the internal stereo-bus.

A fixed level stereo-input can accommodate the signal of one or more additional DRUM-99 modules. These inputs can also be used with the DRUM-06 module (Tom Tom) that also offers a stereo-output.

All five mono signals and the stereo-input are routed to the stereo-output that can be connected to two VCAs, filters or other sound manipulating devices. The output may also be used to connect the DRUM-99 to a mixing-console or audio-interface.

The stereo-output is designed for a possible summing with additional stereo-outputs.

The module has a width of 12 HP (60mm).
Read more
 1 in stock $74.66
MFB
Cat: 695615 Rel: 16 Sep 19
 
Classic envelope generator - 8HP
Notes: The ADSR module is a voltage-controlled envelope generator. Normally, the characteristic is logarithmic, but a linear part can be added. With the help of the loop button, the envelope can also be used as an LFO, then Attack and Decay determine the frequency that goes far beyond 100 Hz. Another special feature is the CV inputs for Attack, Decay and Release. This can be used e.g. control or modulate the times externally. In addition to the normal output, there is an inverted output in parallel.

The power consumption is +/- 30 mA. The module has a width of 8 HP (40 mm).
Read more
 1 in stock $81.16
MFB VC LFO Module (synth module)
MFB
Cat: 695621 Rel: 16 Sep 19
 
Voltage controlled LFO, switchable to oneshot mode
Notes: The module VC LFO accommodates a slowly oscillating oscillator, which is primarily used for modulations. It has five waveforms, CV input with attenuator and a control range from 10 seconds to 100 Hz. In addition, the LFO has its own reset input, over which the waveform is restarted. If you set the speed accordingly and have a separate reset pulse, you can synchronize the LFO with a sequencer. The following waveforms are available: rising sawtooth, triangle, falling sawtooth, rectangle and sample & hold.

The output voltages are maximum +/- 5 volts. The module has a width of 8 HP (40mm).
Read more
 4 in stock $73.58
MFB
Cat: 695617 Rel: 16 Sep 19
 
Analogue VCO, switchable to DCO
Notes: The VCO/DCO is a voltage controlled analogue oscillator module. This can also be used as a DCO, eliminating the need for heating and temperature sensitivity. All functions except for the FM input are also available with the DCO. Sawtooth, triangle, rectangle and pulse are available as waveforms, with soft switching between the individual waveforms. This can also be done with a control voltage, so you have additional PWM modulation.

The power consumption is +/- 30 mA. The module has a width of 8 HP (40 mm).
Read more
 1 in stock $98.47
17/7(ページ1/1)の商品

Filter

Synth modules
DJ機器
Release Date
Featured
Close