Synth modules

Notes: The ADDAC302 Nchunk Control module allows you to connect a Nintendo Nunchuck controller to your modular synth, featuring a two-axis thumb joystick, a three-axis accelerometer and two trigger buttons.

The module provides CV outputs for all of the Nunchuck's parameters and special functions to remap the CV outputs. The remapping can be both continuous or step-by-step and can be accessed through either the dedicated CV inputs or the manual controls.

A specially dedicated Mix output averages between the first two CV outputs, a very useful feature for continuous control parameters.

Mechanical:
- Format: Eurorack
- Width: 8 HP
- Depth: 4 cm

Control Voltage I/O:
- CV inputs: 0 - 10v
- CV outputs: 0 - 5v
- Gate in threshold: 2.5v

Electrical:
- Compatible with +-12v and +-15v power supplies
. Max current: 100mA?
. Bus Board Cable: 8 × 2 IDC (Doepfer style) connector

Notes: The Looping ADSR is an extremely versatile envelope generator. It can act as a traditional ADSR envelope requiring a gate signal to activate or as a looping ADSR. Envelopes can be output with both linear and exponential curves. In Loop Mode it repeats the cycle of Attack, Decay, & Release. Once the Release phase is complete, it loops back to the Attack and begins the cycle again. The Looped envelope can be further manipulated with the Loop Scale knob. Loop Scale shrinks the overall size of the envelope while keeping the ratio of A:D:R identical. All knobs on the Looping ADSR have CV input. As with all Hungry Robot "Modular Boxes" the Looping ADSR can be powered with a simple 9V DC, Negative Center power supply.

KNOBS
-ATTACK: Sets the attack length (1st stage of ADSR cycle). Determines how long it takes to come to full voltage after gate is applied (up to 10 sec.)
-DECAY: Sets the decay length (2nd stage of ADSR cycle). Determines how long it takes to go from full voltage to sustain voltage (up to 10 sec.)
-SUSTAIN: Sets the sustain level. Determines what voltage the envelope returns to after decay stage
-RELEASE: Sets the release length (Final stage of ADSR cycle). Determine how long it takes to return to 0V after gate is released (up to 10 sec.)
-LOOP SCALE: When in loop mode, this knob scales down the length of the envelope while keeping the ratios identical

SWITCHES
-LIN/EXP: Selects the envelope type: linear vs. exponential curve
-LOOP/ADSR: Switches between Loop and ADSR mode. LOOP turns the loop on. ADSR is a traditional ADSR requiring a gate signal
-RPT./GATE: Works only in LOOP mode. RPT. automatically repeats the loop without a gate. GATE mode requires a gate to begin looping.

PATCH POINTS
-LS.CV: CV input for Loop Scale. Allows for CV control of this parameter.
-A.CV: CV input for Attack. Allows for CV control of this parameter.
-D.CV: CV input for Decay. Allows for CV control of this parameter.
-S.CV: CV input for Sustain. Allows for CV control of this parameter.
-R.CV: CV input for Release. Allows for CV control of this parameter.
-GATE: Gate input for ADSR mode as well as Gate/Loop mode
-OUT: Output of final envelope for all modes.

Dimensions: 4.7" x 3.7" x 1.96"
Power: 9V DC - Negative Center - 2.1mm Barrel

Notes: The CVx 1U expander module has eight user-configurable outputs and connects to the MIDI 1U module. Using the Intellijel Config app, you can assign each of the eight jacks to generate just about any type of voltage that can be derived from a MIDI signal; pitch, gates, triggers, clocks, velocity ... you name it! You can chain up to four CVx modules to a single MIDI 1U to add a whopping 32 additional channels of midi control to your modular.

Each CVx module can also allow you to generate 2 or 4 voice polyphonic controls with selectable voice allocation modes. The connectivity, feature set, expandability, and compact size make the MIDI 1U + CVx system ideal for integrating your modular gear with the rest of your rig.

Intellijel's MIDI 1U system comprises several elements, which work together to provide flexible, programmable MIDI-to-CV conversion to your Eurorack modules: The system comprises two mandatory components, and one optional component:

MIDI 1U module - This 14HP 1U module receives MIDI from an attached, external MIDI input connector (7U case, Palette case, or MIDI IN Jacks 1U module), and extracts (by default) Pitch, Velocity, Mod, CC, Gate, Trig, Clock and Reset messages - sending the proportional voltages to individual 3.5mm jacks for patching.If desired, the CC and MOD jacks may be configured to respond to either Channel Aftertouch or High Resolution CC, and the Reset jacks can be configured as a Run jack, instead. Additionally, MIDI 1U features an alternate Dual Mode, which maintains the Clock & Reset functionality, but uses the other six jacks to transmit Pitch, Velocity and Gate messages derived from two separate MIDI channels.

MIDI input connector - the MIDI 1U module does not have its own MIDI input jack. This enables you to use the MIDI/USB inputs built-in to your Intellijel 7U Performance Case or Palette Case. If you don't own one of these cases, you can purchase the MIDI IN Jacks 1U module to connect an external MIDI device.

CVx 1U module - This optional 14HP 1U module connects to the MIDI 1U module and adds an additional eight 3.5mm CV outputs. These outputs are fully programmable using the Intellijel Config app, and greatly expand MIDI 1U's ability to control your entire Eurorack system.

Width: 14HP
Depth: 32mm
Power: 55mA @ +12V
6mA @ -12V

Notes: Row Power is a clean, regulated, and protected power solution for Eurorack systems. Row Power 45 provides enough power for two to three typical Eurorack rows (typically up to about 312HP):
+12V @ 2.0A maximum, 1.5A recommended
-12V @ 1.4A maximum, 1.2A recommended
+5V @ 1.5A maximum, 1.2A recommended

Simply plug a universal power supply (laptop style) into either of the barrel plugs on the 4HP panel. Connect your modules via flying bus cables or the Bus Stick. For custom power systems, the Row Power 45 has a set of easily soldered holes for using large gauge wire or MTA156 connectors to connect to distribution bus boards.

Multiple Row Power modules can be powered from a single power brick by daisy-chaining with an inexpensive barrel cable. The Row Power 45 can also be daisy-chained to 4ms Company's Pod enclosures. Each power supply is independently regulated and protected for ultra-low cross-talk between rows/pods.

The Row Power 45 is compatible with the 4ms Row Power Shield. This device (sold separately) attaches to the back of the Row Power 45 and monitors the amount of current being drawn, as well as the voltages of the power rails. The information is sent over Bluetooth to be displayed on a phone or tablet.

Electrical and Mechanical Specifications

Module Size:
4 HP Eurorack format module

Power Output:
Maximum average load under normal conditions: +12V @ 2.0A, -12V @ 1.4A, +5V @ 1.5A
Maximum average load under any condition: +12V @ 1.5A, -12V @ 1.2A, +5V @ 1.2A
Powered by laptop-style DC power supply: 2.1mm barrel, positive center, 15V-20V.

Included with the Row Power 45:
16-to-16 pin power cable
2 M3 Knurlie screws

Notes: The original MiniMod Glide +Noise module was based exactly on the original Minimoog Model D circuitry, which was designed to be used with the built in Model D keyboard, and because of its vintage design its range was severely limited to 5 or 6 octaves, and it also responded to positive voltages only. Another limitation was that it would not return fully to zero when selecting long glide times, which restricted the range even more.

So we made the decision to re-design the MiniMod Glide + Noise using modern precision parts, and we have come up with an all new circuit which has exactly the same function, but with a hugely extended range. It has the same Glide slope characteristic (a slightly curved Linear Glide) as the Model D on which the MiniMod is based, however in response to many requests from customers we have adjusted the glide up and down speeds so that they are now very similar , which is much more useful in real world applications that the earlier MK1 version which (like the Model D) would glide up considerably faster than it would glide down.

The new Mk2 MiniMod Glide Noise module now has an impressive 14 octave range, and can respond to negative voltages down to -5V. This is a very useful feature, as our MiniMod VCO's will respond to negative control voltages and produce correspondingly low frequencies; so it is now possible to glide down quickly or slowly to crazy sub bass levels! The hold feature has been improved too, it covers the full audio range as well as DC control voltages, and works as a track and hold module with Eurorack signal levels.

A further enhancement is that the Mk2 module can now (using selectable jumpers) transmit or receive pitch CV to the Eurorack power bus; for example, the Glide CV Output can now be directed to the Bus in order to send CV's to (for example) three VCO's via the bus without the need for a passive multi and four patch cords!

The Noise section of the module is unchanged, except that we have slightly boosted the level of the Red Noise output to bring it more in line with Eurorack control voltage levels.

Lastly, it is much shallower - Mk1 Glide Noise had a depth of 54mm, and it was the only MiniMod module that was too deep to fit a skiff style case - and this prevented a full MiniMod system being installed into a shallow Eurorack case. The new MK2 version is only 28mm deep, so this allows both it and a full MiniMod system to be mounted into shallow skiff style Eurorack cases.

Dimensions: 6HP wide, 26mm Deep
Current draw: 36mA Positive, 38mA Negative

Notes: Erica Synths Drum Mixer Lite is compact version of Drum Mixer. It features extended headroom and a dedicated drum compressor of unique design keeps each drum sound clearly distinguishable and add power to the final mix. Bonus feature - effects send output allows to apply external effects to the signals on the first three inputs. LEDs next to each input give visual feedback on the signal level.

Features:
6 inputs
Built in vactrol based drum compressor with Amount and Decay control
Three inputs assignable to main or aux send outputs
Main and Aux Send outputs
Signal level indicator LEDs

Mixer gain: -+6dB
Power consumption: 59mA@+12V, 36mA@-12V
Module width: 10HP
Module depth: 35 mm

Notes: Module A-112 is the combination of a voltage controlled 8 Bit Sampler and a wavetable oscillator. On top of it the module is able to generate some special effects. A-112 was designed as an additional sound source with the typical sounds of the early 8 bit samplers and is not comparable with the modern polyphonic MIDI samplers available on the market.

Sampling mode: 8 bit audio resolution, 128kB memory in 2 banks 64kB each (equivalent to 2 seconds of sampling time for each bank with 32 kHz sampling rate), audio input with attenuator, overload display in record mode (gate LED), possibility of MIDI Dump to store sounds in a computer via MIDI, non-volatile memory for the 2 samples in the module, manual tune control for adjustment of sampling rate for record and play, CV input (~ 1V/Oct), both manual tune and CV determine the sampling rate respectively the pitch (pitch range is 5 octaves), gate input (not a trigger: the sample starts at the positive edge of the gate signal and is played as long as gate is high or until the end of the sample is reached), manual Gate button, non-filtered audio output (thus quantizing noise can be used as an element of the sound intentionally).

Wavetable mode: special appearance of the sampling mode when playing a sample, the audio input is now used as a second control voltage input for moving through the sample in 256 byte wide loops (wavetables). The control voltage required to move through all wavetables applied to the input "Wave CV In" is in the range -2.5V (wavetable 1) ... 0V (wavetable 127) ... +2.5V (wavetable 256) when control "Atten." is set fully clockwise. To achieve the typical wavetable oscillator sounds the sampling memory must contain corresponding wavetable data (e.g. loaded via MIDI dump). These data contain a set of wavetables with different harmonic content (e.g. a filter sweep) to get the typical wavetable sound while moving through the tables via CV. But you may also use a "normal" sample and go through the sample with CV to obtain partially amazing sounds never heard before. You may use for example sampled speech and go with CV through the syllables or speech shreds to get really very extreme sounds. An ideal addition for this feature is the Offset/Attenuator module A-183-2 which can be used to adjust the position of the wavetable (Offset) and the modulation depth (Att.). The corresponding jumper of the A-183-2 has to be set to bipolar offset (as the A-112 requires -2.5V...+2.5V to pass through all 256 wavetables). As modulation source an LFO (A-145, A-146, A-147, A-143-3), ADSR (A-140, A-141, A-142, A-143-1/2) or a random voltage (A-118, A-149-1) may be used. Even a ribbon controller (A-198 or R2M), the Theremin module A-178, the Joystick A-174 or the Wheels module A-174-2 are useful to drive through the wavetables.

Effects: Additionally, the module offers - in a way free of charge - some effects like delay, reverse delay, pitch shifting or freeze. But it has to be pointed out that due to the 8 bit audio resolution these effects are not comparable to high quality effect units and should be understand as an extra for nothing. The A-112 is not an effects unit!

The sampling time of the A-112 is about 1...30 seconds corresponding to a sampling frequency range of about 60kHz...2kHz (64kB@60kHz ~ 1 s, 64kB@2kHz ~ 30 s).

Technical note: the module uses a battery for the non-volatile storage of the sampling data. Batteries have a limited lifespan and have to be inspected at least every two years. For details please refer to the FAQ page of our website: Lifespan of rechargeable batteries (used for memory backup).

Notes: Sewastopol is a multifunction Eurorack module designed for easy interfacing of external gear to your modular environment. It can export line and professional level audio, import audio from instruments and electroacoustic transducers, and analyse the incoming audio to generate voltages and triggers to control your modular system.

This is a second, vastly improved revision to the original 2014 Sewastopol, featuring a completely redesigned preamplifier circuit, better ergonomics and various other improvements.

Notes: Clep Diaz is a handy and small step CV and LFO generator. In step and random modes, use the encoder to control the number of steps in the sequence; in LFO mode, the encoder controls the amplitude of the wave. Toggle the directionality of the sequence: up, down, or up/down to customize the CVs further. CD also gives CV control over the number of steps in the sequence and an end-of-cycle trigger output. Unipolar and bipolar outputs allow maximal control.

Notes: A-105-4 is our first polyphonic filter and contains four
identical 24dB Lowpass filters (SSM2044 type). It has
available common manual controls and CV inputs with
attenuators for these parameters:

Frequency (F)

Frequency Modulation Intensity (FM)

Resonance (Q)

Audio Input Level (L)
Each filter has available a separate FM input as well as an Audio Input and Output. The FM input is typically connected to the output of the associated envelope generator (e.g. A-141-4).
The envelope amount for all four filters is controlled by the FM knob and the CVFM input by means of four built-in VCAs, which are controlled by the FM control and CVFM input. This allows also voltage control of the envelope amounts.

In addition common frequency modulation for all filters is possible (e.g. by an LFO). For this the CVF input with attenuator can be used. The range of the audio input level control (L) allows also clipping/distortion with typical A-100 audio levels
(e.g. from A-111-4) at the filter inputs. Even this parameter is voltage controllable as well as the resonance (Q).
Application: polyphonic patches (four VCFs with same parameters).

Notes: The window comparator is a very useful circuit building block that is common in general electronics, but rarely found in modular synths. While a regular comparator activates when the input signal voltage is higher than a threshold level, a window comparator checks if the voltage is between two levels (these form the 'window').

Compare 2 combines two such comparators and a logic section in 8 HP. The result is an advanced tool for extracting gates and pulses from analogue signals in Eurorack synths.

The detection windows are defined by the shift and size parameters, which can be varied using the knobs and CV inputs. Complementary gate outputs are available, with big three-colour LEDs showing each comparator's status.

All inputs are normalised from the left section to the right, but the two comparators can also be used completely independently. On the bottom, the outputs from both comparators are combined in various ways by the logic section, which also features LEDs.

You'll find a use for this truly multi-functional module in practically any patch, processing either CV or audio: complex rhythm generator, dual pulse width modulator, frequency multiplier/divider with PWM, digital ‘ring modulator’ with PWM, dynamic depth VCO synchronizer, voltage controlled swing, logic function array with adjustable thresholds... and many more applications waiting to be discovered!

Notes: While modular synthesisers are most often used as stand-alone instruments, they also present exciting opportunities for processing external signals. Anything from an electric guitar to an effects send on a studio mixing desk can benefit from the unique sonic capabilities of even a modest Eurorack system.

However, patching in an external source usually requires an adapter cable and plenty of clean gain to bring the signal to Eurorack level. If the signal source is balanced, a balanced input is required as well to provide the best possible interference rejection.

Receive 2 (or RX2 for short) provides a convenient all-in-one solution. It offers two universal external inputs, which accept both balanced or single-ended signals via XLR or 6.35 mm jack connectors.

The circuit incorporates low-impedance design practices, radio-frequency (RF) filtering and premium balanced receivers to provide transformer-like interconnect performance in a compact and affordable module. And thanks to the electrostatic discharge (ESD) protection, it’s rugged enough to survive the rigours of performing on the road.

The very clean integrated pre-amps feature variable gain, ranging from unity to +40 dB on each channel. As a result, Receive 2 can handle just about any signal source you may encounter, including electric instruments, piezoelectric pickups and many dynamic microphones.

Adjusting the gains is a breeze thanks to the dual peak-responding LED meters. A mix output is included as well, so external signals can be easily mixed directly in the module.

Notes: For decades, the voltage controlled slew limiter has been a staple of modular synthesisers. With its extreme versatility, it can be used to slew control voltages (CVs), create envelopes, as a low-frequency or audio oscillator and much more.

Today, Contour 1 brings a fresh approach to this classic circuit. It delivers much improved performance and control by incorporating modern design techniques.

At its most basic, a slew limiter slows down the rate of voltage change in a signal. On Contour 1, the rising and falling rates can be individually set using sliders and CV modulation.

The gate and trigger inputs allow the module to be used as a function generator: create snappy attack-release (AR) and attack-decay (AD) envelopes, with slope times ranging from 500 us to 30 seconds. The dedicated gate input makes it easy to generate +10 V envelopes from any signal source. Using the large tactile push button, AD envelopes can be manually triggered. A trigger will also reset the output voltage.

When set to loop mode, Contour 1 will continually re-trigger itself. In this mode, it fulfils the role of a variable-shape low-frequency oscillator (LFO) or temperature-stable voltage controlled oscillator (VCO) in the audio range.

Both the rising and falling slopes can be individually bent, from concave through linear to convex. While doing so, the deviation in slope time, and thus oscillation frequency, is kept to a minimum. Since the bend parameters are separately voltage controllable, boundless modulation possibilities present themselves.

Explore anything from shape-shifting envelopes to rich VCO timbres: Contour 1 will make you re-think what a slew limiter can do.

Dimensions
8 HP
30 mm deep

Current Draw
90 mA +12V
85 mA -12V

Notes: The "uMCLK Divider" module can either work as a MIDI clock divider or as an analog clock divider. The divider outputs are assigned differently in both operating modes.

After receiving a MIDI start command, the module works as a MIDI clock divider. There are fixed dividers on 11 outputs. Via the divider output KEYS, triggers can be triggered and mixed via MIDI notes. The keyboard zone extends over three octaves. With the help of the LEARN key, the receive MIDI channel and the lowest note of this 3-octave range can be defined.

When stopped (i.e. after receiving a MIDI stop command or after switching on), the module works as an analog clock divider and divides the analog clock present at the CLOCK input. The 12 analog divider outputs can be reprogrammed via SYSEX. Ready-made SYSEX files are already available (e.g. for even / odd dividers, Fibonacci series, offbeats, etc.). The RESET input resets the analog counters or serves to deactivate the analog divider.

Connections:
- Ribbon cable adapter for Doepfer bus +/-12Volt
- Inputs: 2x Clock/Gate,Reset (0/+5..10V), 1/8th inch mono jacks
- 1x MIDI (TRS-B standard) 1/8th inch stereo jack Outputs: 1x MIDI (TRS-B standard) 1/8th inch stereo jack
- 14x Clock/Gate Divider, 1/8th inch mono jacks

Control elements:
- 1 push button with LED (LEARN key) 16 LED's
- Current consumption: max. +70..80mA / - 0 mA
- Size: Euro rack format 3U / 6HP 30x128,5x40 mm

Dimensions
5 HP
40 mm deep

Current Draw
80 mA +12V

Notes: Viol Ruina is an all-analogue distortion and lowpass filter with an internal envelope follower and self-modulating cutoff. The four-pole design is reminiscent of the classic filters we all know but with a completely new and slightly ridiculous twist. The independently addressable distortion circuit takes VR into overdriven paradise with a shocking amount of drive. Built-in envelope following makes an easy way to create dynamic patches with the flick of a switch, and feedback FM takes VR to a whole new realm of filthiness. Run a sound through VR, you'll get something cool out of it.

Notes: Row Power is a clean, regulated, and protected power solution for eurorack systems. Row Power 35 provides 35W of power, suited for any typical eurorack row (84HP to 168HP):

+12V @ 1.4A
-12V @ 1.25A
+5V @ 1.0A

Simply plug a universal power supply (laptop style) into either of the barrel plugs on the 4HP panel. Connect your modules via flying-bus cables or the Bus Stick.

Daisy-chain multiple Row Powers to use a single power brick for multiple rows (typically 3-5 rows per power brick). Each row will be independently regulated and protected for ultra-low cross-talk between rows. Rows can also be hot-swapped (plugged/unplugged without powering the whole system down).

Notes: Ultra-simple 16-step Eurorack CV sequencer with randomisation option and storage for up to 16 patterns. Straight to the point business, all in just 4HP of rack space.

Supplier notes:
Small, easy-to-program sequencers are a bit of a rarity. Vox Digitalis is our answer to this issue. With intuitive displays and simple controls, VD is perfect for all your pitch CV needs. Set your sequence length, dial in each note, randomize, save and load 16 sequences -- VD does all the stuff the big sequencers do, just in 4HP.

Notes: Erica Synths Cymbals is a distinct topology digital/analogue module, where cymbal samples are passed thru AS3330 based VCA and controlled via envelope generators of unique design. The module features 10 sets of custom Crash and Ride cymbal samples with Tune control and individual Decay control. Accent and CV control over Tone and Decay allow you to create lot of variations in the Cymbals track. An extra feature is sample looping - when it's on, a certain part of the sample is looped while the envelope decay is on, thus creating a distinct, delay-like effect. Cymbal samples are developed by producer and musician Nero Bellum.

Features
10 sets of custom cymbal samples
Analogue VCA and EG
Tune and Decay controls
CV control with an attenuators over Tune and Decay
Sample loop for Crash and Ride
Manual triggers
Accent for better expression

Audio output level: -5...+5V
CV level (full span): -5V - +5V
Accent CV level: 10V
Tigger level: 5V
Trigger time: 1ms
Power consumption: 95mA @ +12V, 36mA @ -12V
Module width: 10HP
Module depth: 45mm

Notes: The Listen Four is a four channel stereo mixer with line, modular, and headphone outputs. Two mono channels with Pan knobs and two stereo channels with dual inputs provide optimal compatibility with both stereo and mono signals. The Listen Four can be daisy-chained to other Listen modules to create a larger mixer with sub-mix outputs.

Notes: The Listen Four Quarters is a four channel stereo mixer with 1/4" (6.35mm) TRS balanced outputs and 1/8" (3.5mm) headphones output. Two mono channels with Pan knobs and two stereo channels with dual inputs provide optimal compatibility with both stereo and mono signals. The Listen Four Quarters can be daisy-chained to other Listen modules to create a larger mixer with sub-mix outputs.

Notes: VCO:

- Tune: manual tune control (with an internal jumper the range can be set to ~ +/-1 half an octave or ~ +/-2.5 octaves)
- Oct: range switch -1 / 0 / +1 octave
- Mod: modulation depth (attenuator wired to the Mod. socket)
- Dest: switch that is used to address the modulation to frequency modulation (position FM) or pulsewidth modulation (positon PM), in centre positon no modulation
- PW: manual pulsewidth control for rectangle waveform, PW can be also modulated by the Mod. input as mentioned above
- Wave: waveform switch (sawtooth / off / triangle), the sum of the waveform chosen by this switch and the rectangle is fed into the VCF (to turn the rectangle off the PW control has to be set fully CCW or fully CW)
- 1V/Oct. (socket): external CV input for VCO frequency (1V/octave)
- Access to internal bus CV (via jumper, optional, please remove the bus jumper if this feature is not used to avoid unwanted frequency modulation as then the unused CV line of the bus works as a kind of antenna)
- Triangle core VCO, frequency range about 32Hz ... 8kHz

Balance unit:

- The balance unit is made of two VCAs which are controlled by the sum of manual Balance control and the balance CV input in the opposite direction.
- The audio input of VCA1 is hard-wired to the VCO output, audio input 2 is connected to the socket Ext.In.
- The output of the balance unit is used as audio input for the VCF
- Bal.: manual balance control, fully CCW the internal VCO is used, fully CW the external signal (Ext.In) is used, at centre position both signals have about the same level
- CV Bal.: CV input for balance (range about 0...+5V)
- Ext. In: external audio input for VCA2, about 5 Vpp level required for similar loudness as the internal VCO
- This socket is normalled to the internal VCO suboctave f/2 signal (rectangle with half the frequency), if no external signal is applied the suboctave signal is used as the second signal for the balance unit

VCF:

- 24 dB low pass
- Frq: manual frequency control
- FM1: frequency modulation depth (attenuator wired to the VCF FM1 socket, the socket is normalled to the internal Envelope signal and then FM1 controls the modulation depth of the internal envelope applied to the filter)
- FM2 (socket) : second CV input for VCF without attenuator (about 1V/octave), can be used e.g. for VCF tracking by connecting the same CV which is used also for the VCO frequency
- Res: manual resonance control (up to self oscillation)
- If the VCO is turned off (waveform switch = centre position, pulsewidth control = fully CCW or CW) and the VCF resonance is set to maximum the module can be used as a sine oscillator, the tracking at socket VCF FM2 is about 1V/octave (not as precise as the VCO but much better than most other filters)
- ~ 11 octaves frequency range (~ 10 Hz ... 20kHz)

VCA:

- Gain: manual amplitude control (initial gain), can be used to open the VCA without envelope signal
- VCA (switch): used to switch between gate and envelope as control signal for the VCA, in centre position the VCA is not controlled by envelope or gate
- Note: when gate is used the VCA is controlled directly by the gate signal (i.e. hard on/off), this may lead to clicking noise under certain conditions (especially with low VCO/VCF frequencies)
- Special control scale: exponential scale in the range from about -20dB to -80/90dB, linear scale from about -20dB to 0dB
- Remark: this special control scale results in a loudness behaviour that is a bit different from pure linear or exponential VCAs
- Out: audio output of the module (= VCA output)

Envelope:

- Gate (socket): Gate input (min. +5V), can be normalled to the bus gate signal by means of a jumper
- Att: manual control for Attack
- D/R: manual control for Decay/Release
- Env. (switch): used to switch between A/D, ADSR and A/R mode of the envelope generator, in centre position (ADSR) the sustain level is fixed to about 50%
- Envelope (socket): envelope output (about +10V)
- CVT (socket): CV input for time control, by means of two internal jumpers one can select which time parameters are controlled by the CVT input (e.g. A only or D/R only or A/D/R) and in which direction (i.e. if an increasing CVT shortens or stretches the time parameter in question)
- Envelope LED display
- Attack time range: ~ 1ms ... 5 sec (can be extended by using the CVT input)
- Decay/Release time range: ~ 1ms ... 15 sec (can be extended by using the CVT input)

Notes: The module can record the joystick movement up to a length of over a minute. The sequence remains stored in the battery-backed RAM after switching off. When playing the sequence, it can be manipulated in speed and playback direction.

There is a FREEZE function to hold the current joystick position plus an external reset input. In addition, a GATE is set during movement and a CV voltage is output as a function of the joystick movement. The ranges of the X / Y output voltages are bipolar +/- 5v or unipolar from 0 to + 10v. Both channels X and Y have a passive attenuator potentiometer, so that the voltage range can also be set lower.

Notes: Versatile stereo digital filter based on Endorphin's Grand Terminal module. CV-controlled cutoff, resonance and separate high-pass filter. Simple but effective.

Supplier notes:
The Squawk Dirty To Me is a stereo filter with voltage controlled resonance. It features eight filter modes and zero-delay feedback.

- Simple and effective 6hp stereo VCF
- 8 filter modes available with meta CV scanning, famous zero-delay feedback Grand Terminal filters
- Additional hi-pass filter in series quickly cuts the boomy low end

Notes: Reverse-engineered from the original machine, our BD909 is an identical recreation of the original all-analog drum circuit of the TR-909. We've added additional controls and synthesis features that turn this classic circuit into a chest-pounding analog bass drum laboratory - all tightly packed into an 8HP module. The BD909 sound differs from our BD808 in that the main sonic energy is centered in the mid to low frequency range (as opposed to the low frequency range of the BD808). This frequency range gives the needed headroom allowing your bass Lines to deeply fill up the low end while the kick drum rides on top - creating a clear and punchy mix.

The BD909 includes all the controls found in the original: Attack, Decay, Tune Decay, Accent and Level. We have gone beyond that and added controls that further increase the palette of sound this circuit is capable of. First off, we've added a tuning control knob for the oscillator and included its own CV input and attenuator that let you tune your 909 kick with your bass lines. Next, we added control knobs for the tuning attack and extending tuning decay - each one affects the other, allowing for very intuitive and interactive sound shaping - this feature opens up numerous "sweet spots", and provides the ability to center the energy peak at different parts of the sound. Finally, we offer additional punch and distortion by giving complete control over the internal waveshaper, which allows you to overload the waveform manually or with voltage control.

Beginning with the classic and pure sound of the 909 kick, these additional functions greatly expand the BD909's flexibility and let it create powerful analog bass drums that range from soft and smooth to punchy and aggressive - and everything in between.

Notes: 'Tangle Quartet' is a high quality quad linear voltage controlled amplifier (VCA) providing individual level control of 4 signal inputs with both individual outputs and a combined 'mix' output (for non patched outputs) . Control signal inputs and associated attenuation controls allow for voltage control of signal levels. Control inputs are normalised to 5v thus providing manual mix control in the absence of control signals.

Technical Specifications:

Supply: +/-12V (Reverse voltage protection)
Current Draw: ~80ma
Size: 8 HP
Depth: 32mm (including power header)

Notes: The EVEN VCO is a voltage-controlled oscillator that offers stability and high precision tuning over 10 octaves. A redesigned temperature compensation circuit maintains the oscillator stable against voltage and temperature drops.

Specifications:

Current needs: +12V: 36mA, -12V: 26mA
Width: 8 HP
Depth: 22mm, (28mm DIY) including power connector
Aluminium, heat-treated front panel.
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: The Sampling Modulator is a multi-function module that lies somewhere between a VCO, a Sample & Hold, and an 8 step trigger sequencer.

Sequencer Clocked Sample & Hold

In this mode it acts like a regular Sample and Hold (S&H) but since it is "sequencer clocked", it is capable of much more interesting patterns than the usual S&H melodies.

The CLOCK input can work in two ways: 1. As a typical clock 2. In "positive going hard sync" mode allowing you to create shuffling and polyrythmic effects.

The HOLD input can be used to keep certain notes playing.

Analog Down-Sampling Effect

In this mode (with the clock running at audio rates) you can go from nasty and harsh sampling rate reduction to an almost clean signal. (The clock run up to 25Khz without external CV and up to 200Khz with CV on the input).

Sampling Modulator/Shaper

Thanks to the V/Oct clock, by feeding a simple waveshape such as a sine wave to IN, and pitch CV to the VCO as well as to the Sampling Modulator CV input, their related frequencies and aliasing caused by the sampling rate reduction are capable of creating clangorous metallic sounds, 8 bit textures and much more.

The game becomes much more interesting when you try to destroy the wave by flipping on and off the switches of the sequencer (which at times can make it sound like three VCOs running in unison).

To understand how the Sampling Modulator works, keep in mind that we are working with a temperature compensated ramp core VCO with more than 4 octaves of tracking. This allows the timbre to stay the same while you move through the scale as the internal and external VCOs are synced in a fashion similar to "frequency related sampling rate modulation"

Unusual V/oct VCO You can use the trigger outputs as a pulse VCO. Flipping the switches on and off the switches can offer a lot of interesting timbral changes.

Notes: nRings

This is a new build of a micro version of Rings from Mutable Instruments. MicroRings, also called NanoRings, retains all the same functionality as a full-size Rings module.

The module is fully assembled, tested, and calibrated. Eurorack power cable is included.

These modules use tall bushing potentiometers to offer a more stable feel.

Notes: Erica Synths Black LPG is our take on Lowpass Gate idea - it's designed from scratch
module featuring 2nd order lowpass VCF (the original Buchla lowpass gate was 1st order
VCF) and VCA combo with distinct resonance circuit on top. Voltage control over VCF cuto
frequency/VCA oset and mode (VCF/VCF+VCA/VCA), as well as built in decay envelope
generator makes it a versatile module for sound shaping in any modular setup.

FEATURES:
Three vactors for 2nd order VCF
VCF/VCF+VCA/VCA modes
Manual and voltage controlled cuto/oset
Manually and voltage controlled mode selection
Manually resonance depth control
Resonance overdrive switch
Built in decay envelope generator
Manually and voltage controlled decay time
Envelope CV output
Ski-friendly design

SPECS:
Audio output amplitude 10Vptp
CV range (full span) -5V - +5V
Max Decay time 4''
Panel width 10HP
Module depth 35mm
Power consumption 44mA@+12V, 45mA@-12V

Notes: Erica Synths Black VC Clock is the beating heart of your modular system.

The beating heart of your modular system in 10HP.

This module generates several clock signals simultaneously and has some more advanced features like tap tempo, shuffle and divide, both for controlled rhythmic music production and for experiments with high level of uncertainty. You may also find the adjustable and even random duty circle of shuffling and random clock outputs interesting. Bonus feature - the module can be used as a performance time stopwatch.

Erica Black series are high-end modules with unique functionality. Only the highest quality components are used and all inputs and outputs are protected against undesired overvoltage. When designing the Black Series, design and usability was prioritised over module width. Big knobs are assigned to functions that make difference in sound. Together the Erica Black series are a range of modules that make an entire synthesizer.

Technical specifications:

Max input level: -10V - +10V
Clock signal level: 0 - +5V
Clock rate: 30 - 400BPM
CV input level (full sweep): -5V - +5V
Power consumption: 40mA@+12V, 5mA@-12V
Module width: 10HP
Module depth: 25mm

Notes: Unusual output and mastering module, inspired by studio and radio mastering tools but fitting into just 6hp. Includes multi-band compression, mid/side stereo processing and brickwall limiting.

Supplier's Notes:
Golden Master is a multiband processor module in Eurorack format. Inspired from the studio mastering and radio loudness units from the 90's, this tool is a game changer for everyone who performs live with a Eurorack synthesizer.

The whole magic of Eurorack lies in its raw sound and simple analog mixes - processing through the Golden Master brings instant punch and sound pressure, as well as controlling the overall volume.

Power consumption: 135mA at +12V and 25mA at -12V
Depth: 30 mm (with ribbon cable connected)
HP : 6

Notes: Premium analogue delay from Erica's flagship Black Series range. Two bucket brigade device delay lines work simultaneously with smooth crossfading and tons of voltage control. Lovely.

Supplier's Notes:
Erica Black Series include high-end, unique functionality and superior quality modules. Only the best, highest quality components are used, all inputs and outputs are protected against undesired overvoltage. When designing Black Series, put design and usability superior. Big knobs are assigned to functions that make difference in sound. Erica Black series consist of range of modules that are needed to put together entire synth. Enjoy!

The Erica Synths Black BBD is one of kind analogue delay module. It features two BBD lines: short, 1024 stage and long, 4096 stage, that work simultaneously and you can smoothly fade between those two, thus creating distinct multitap effect.

Furthermore, an advanced BBD clock noise cancellation circuit is implemented that reduces unwanted BBD noise without filtering higher frequencies of audio signal. Most of parameters are voltage controlled, which allows to integrate the module in complex modular setups.

Time

This is delay time manual control.

Because of BBD clock suspension circuit, delay time can be pushed in extremely long regions, however in that case BBD clock noise may appear. The Time CV is added to the knob setting.

In level

This is the input attenuator switch. Select among full amplitude, half amplitude and audio off.

BBD mode

This control smoothly fades between short and long delays. Any setting in-between will result in distinct multitap delay effect.

LFO rate

Adjust the internal modulation LFO rate. The internal LFO controls delay time, and it's automatically disengaged, when an external modulation signal is connected. The LED gives visual feedback on the LFO rate.

LFO shape

Select the LFO shape. Three shapes are available - triangle, square and in-between shape - mix of triangle and square.

Input

This is the audio input of the module. This is manual Dry/Wet mix. The MIX CV is added to the knob setting.

Colour

Even though the module has BBD clock suspension circuit, the colour switch provides extra lowpass filtering of the signal. At top setting no filtering is applied, at lower settings increasing filtering is present.

Feedback

This is the delay feedback manual control. In extreme clockwise settings the module goes into self-oscillation, and by adjusting delay time and BBD mode settings, the module becomes a drone machine. The FBK CV is added to the knob setting.

CV level

This is the Time CV level attenuator. If nothing is patched into TIME CV socket, it controls the internal LFO amplitude.

WET out

This is the WET signal output of the module - use it for advanced patches.

Out

This is the main output of the module.

Time CV; FBK CV; Mix CV;
These are CV inputs for Time, Feedback and Dry/Wet mix.

SPECS:
Audio level 10Vptp
CV level (full span) -5V - +5V
Power consumption +95mA, -81mA
Module width 12HP
Module depth 35mm

Notes: Endorphin.es Cockpit² is a 4-channel stereo mixer with side-chain ducking.

Key facts:

Increased headroom
Improved sound quality
The LEDs are blue/red instead of red/green (Daltonic friendly)
No TRRS jacks anymore
New aluminium knobs on the black module version

Power consumption:
240 mA +12V
75 mA -12V
0 mA 5V

Dimensions:
6 HP
38 mm deep

Notes: 10HP Edges Clone with integrated midi interface and PSImidi which allows any TRS midi cable to be used.

MIDI Functionality:

MIDI Learn: Press this button and send a midi note. The device will use that channel as the base channel

MIDI Mode: This button cycles between two operational modes.

1. 4 single voices trigger on 4 midi channels starting on the base MIDI channel (i.e. base channel is channel 2 so the voices are mapped over channels 2, 3, 4, 5)

2. Simple Poly mode where each voice plays on a different note on the same midi channel

Note about MIDI and Gating: The gate is normalled OPEN by the Gate 1 input. This is by design but will also force the gate open when the device is triggered by midi. Placing a dummy jack will break the open normal the gate will trigger via MIDI normally

Notes: 8HP Tides version 2

Fully calibrated.

Notes: 8HP Tides version 2

Fully calibrated.

With LED Pots for the attenuverters.

Notes: This is 2 x opensource branches. The input of channel one is normalled to all other inputs so you can run this as 1 to 4, 2x 1 to 2, etc. Dual Color LEDs on sliders

Notes: 6HP Micromodule of MI Warps.

Notes: A 6HP version of Mutable Instruments Peaks that adds CV inputs and attenuverters for each of the four parameters.

It can be an ADSR-style envelope generator, an LFO and a drum emulator. By default, the Dead Man's Catch (DMC) firmware will be loaded, which adds the Alt ENV, ALT LFO, ALT Tap, Alt Drum modes below.

The module is calibrated, comes with a power cable, and a one year warranty.

Additional Dead Man's Catch firmware modes:

Basic (original modes):

Envelope
LFO
Tap LFO
Bass/Snare Drums

Alternative ENV:

Double attack envelope
Repeating attack envelope
Looping envelope
Randomized AD envelope
Bouncing ball envelope

Alternative LFO:

Frequency-modulated LFO (folded sine FM)
Frequency-modulated LFO (random FM)
Varying wave shape LFO ( folded sine WS mod)
Varying wave shape LFO ( random WS mod)
Phase-locked loop oscillator

Alternative TAP Mini-sequencer:

ModSequencer
Pulse Shaper
Pulse Randomizer
Turing Machine
Bytebeats

Alternative DRUM:

FM drum Generators
Randomized bass and snare drum generators
Randomized high hat

Notes: Popple is an 8hp multimode stereo filter based on the Mutable Instruments Ripples V1 filter section. Popple maintains the buttery smoothness of Ripples filter while giving you two separate audio paths. The audio paths share a resonance, control, a frequency cutoff control, resonance CV input, and a v/oct cutoff CV input. Each channel then has it’s own cutoff CV input with attenuverters (which are normalled to a 2.5V signal).

Popple will also self-oscillate at high resonance settings, when coupled with the v/oct CV control, it can also act as a dual sine wave oscillator.

Notes: 221.x2 is a clean and precise utility module that is equally at home mixing Control Voltage as it is audio. At its simplest, it is two independent 2-to-1 mixers that offer per-channel attenuation and inversion, as well as +6dB of gain available at the summed outputs. With a tap of the "All Mix" button, these separate mixes can be combined into a 4-to-1 mix at the "All Mix" output - meanwhile, the first 1+2 mix is still available at its respective summed output. A rear expansion input and output allows for combining multiple modules into larger systems.

In addition, each channel also offers a Direct Output that can be taken pre or post attenuation/inversion.

A 6-volt offset is normalled into the input jacks of channels 2 and 4. This voltage is available at the channel's Direct Output, as well as added to the mixed outputs. Useful as an offset for mixing with another CV signal, or simply as a voltage source.

Each summed output group has two blue LEDs for displaying the shape of the summed CV, and can also serve as signal present indicators for audio. Peak LEDs trigger at ~9.6V, allowing for a bit of headroom before things get out of hand.

Specifications:

Width: 10HP
Depth: 3.3 cm
Power: 133 mA @ 12V
129 mA @ -12V
Inputs/Outputs: All I/O is unbalanced
Input Impedance: 10 Mohms
Output Impedance: Mix Outputs: 330 ohms
Direct Outputs: 10 ohms

Notes: Superior 60 mm quad fader CV source including MUTE feature

The ACL Fader CV Source Module comprises 4 individual faders where each can generate a CV either going between 0 and +5V or 0 and +10V unipolar or -5V and +5V or -10V and +10V bipolar, selectable using 2 jumpers on the backside of the module.

Furthermore there are mute-switches for each channel accompanied with an dual color LED (green/red) which shows the channels mute status. When mute is activated or deactivated, short fade ramps will be generated as well as the fader itself is slightly slew-limited internally in order to generate a smooth CV.

This module is very useful to control VCA's or VC mixers like our VC Amp mix module.

Notes: The SC (Stereo Channel) is a single-channel stereo module for the CGM Eurorack mixer, fully compatible with every other product of this family.

It features a mono/stereo local output which makes it ideal for multitrack recording and advanced parallel processing.

Thanks to its advanced I/O configuration, it can work as stereo-to-stereo, mono-to-mono, mono-to-stereo, and stereo-to-mono.

The gain control and the two mono FX sends can work in pre or post-fader mode, and the pan pot can also work as a dual mono crossfader, making it suitable for blending two mono sources into a single mono sum.

All the parameters are voltage-controllable for creative mixing automation.

Mechanical mute, PFL, and Solo-in-Place complete the feature set suitable both for studio and live performances.

*The SC replaces the C as the primary single-channel CGM solution. The C module is now discontinued.

Notes: Variable Pole analogue filter based on Asteroid Op VCF Tech

Model: Millipede Variable Pole VCF
Analogue Filter, Can easily get Brutal tones.

What does this do?

This is an analogue filter that uses two modern equivalent ssm2164 IC's v2164 from cool audio to do it's magic. This particular filter however allows the user to vary the phase of each pole or filter cell. There are four filter cells total. This is similar to the Blue lantern Asteroid Operator Station VCF. The Asteroid Operator Station VCF has 8 Static filter out puts. Those 8 flavors were found by exploring the circuit found on the millipede vcf and internally installing the resistor ratio for that flavor.

On the millipede vcf you are allowed to find more exotic flavors yourself. Operation is easy. You first have all the poles counter clockwise and the three switches set to mute. This will have the filter as a dark Low pass filter. Then you turn on a pole using the switch and turn the know to hear the change. Pole 3 by default is always on, otherwise there would have been no sound if all poles were muted. Having all the poles set clockwise and active easily gets you into brutal sounding tones in a good way.

There is an on board diode limiter circuit to help tame really harsh tones. This is activated by switch.

The audio input has some gain, so you don't always have it fully clockwise. There is also a capacitor selector switch just like my other filters. This modifies the rez peak.

Dimensions
13 HP
32 mm deep

Current Draw
58 mA +12V
56 mA -12V

Depth: 2.5 inches

Notes: Designed with versatility in mind, the Fold 6 is a six-stage wavefolder with simultaneous series and parallel outputs, dual signal inputs and voltage-controlled folding and overdrive shaping.

Supplier's Notes:
Often considered to be the opposite of filters within a modular system, wavefolders are designed to fold a signal over itself multiple times. This generates additional harmonics, resulting in rich timbres.

While there is a bewildering array of filter types within the synthesiser world, most wavefolders fall within only a few categories. Diode wavefolders in particular come in just two variants: series and parallel circuit topologies. Choosing a specific folder also means being limited to specific sounds and capabilities.

For the first time, Fold 6 puts forward a 6-stage hybrid series/parallel topology, yielding a greater sonic palette than ever in just 4 HP. Having both main (series) and alternate (parallel) outputs means a single module now gives access to just about all wavefolding tones imaginable.

To take things even further, an integrated symmetrical soft clipper limits the output signals to approximately 10 Vpp, keeping the amplitude within typical Eurorack levels and making it easier to create overdriven sounds at high fold ratios. This clipping stage can be driven continuously using the shape parameter, smoothly transforming the folded waveforms into pulse waves for even more harmonic content.

Two signal inputs are included, to mix audio signals or add in a DC voltage for asymmetric folding. The symmetry can also be manually controlled using the dedicated knob. Of course, both fold and shape parameters feature voltage control, to enable continuous timbral modulation.

Moving beyond simple signal processing, Fold 6 also lends itself perfectly for feedback patching, CV folding or frequency multiplication; its modest size belies the sonic capabilities within.

Notes: 32 unique audio effects arranged in 4 banks of 8 effects. Three effect controls plus analog Dry/Wet control with dedicated CV input. High quality stereo signal pass. Assignable CV input to effect controls or to Sample Rate reducer (changes internal clock). Four user storable presets - stores selected program and all three controls. Spin FV-1 based.

The last used effect, assigns and presets are always remembered.

32 effects are simultaneously available, but FX AID can be reflashed with other effects in any order.

Reflashing procedure is quite easy: playing 40 sec long "wav" file of line level amplitude to CV input.

Reflashing mode: hold both buttons for 10 sec.

Please note the reverse CV operation of the Dry/Wet control: positive CV crossfades from Wet to Dry, and negative CV crossfades from Dry to Wet.

By default it runs on 32.77 kHz and, if sample rate reduction assign is used, this sample rate can be decreased down to 150 Hz or brought up to 48 kHz.

80 mA +12V
30 mA -12V
45 mm deep

Notes: 32 unique audio effects arranged in 4 banks of 8 effects. Three effect controls plus analog Dry/Wet control with dedicated CV input. High quality stereo signal pass. Assignable CV input to effect controls or to Sample Rate reducer (changes internal clock). Four user storable presets - stores selected program and all three controls. Spin FV-1 based.

The last used effect, assigns and presets are always remembered.

32 effects are simultaneously available, but FX AID can be reflashed with other user selected Happy Nerding effects in any order. Also the possibility to run freely available third party effects will be added too.

Reflashing procedure is quite easy: playing 40 sec long "wav" file of line level amplitude to CV input.

Reflashing mode: hold both buttons for 10 sec.

Please note the reverse CV operation of the Dry/Wet control: positive CV crossfades from Wet to Dry, and negative CV crossfades from Dry to Wet.

By default it runs on 32.77 kHz and, if sample rate reduction assign is used, this sample rate can be decreased down to 150 Hz or brought up to 48 kHz.

80 mA +12V
30 mA -12V
45 mm deep

Notes: The Fold Processor is a voltage-controlled wave multiplier and sub-octave generator. The circuit is based on a classic diode design that adds odd harmonics by folding the incoming signal, followed by subdivided square waves.

The wave folder creates new waveforms from standard sine, triangle, sawtooth, and square waves and includes a CV input with an attenuator, making it very easy to create beautifully animated folding sounds. Adjustable voltage-controlled Inject alters the bias point creating an even wider palette of sounds.

The subdivide generator squares the fold output generating 4 more sounds spaced one octave apart, each with its own gain knob and mixed to the Subdivide output jack. Mixing the four can create anything from discordant square wave swarms to sweet harmonic oscillator stacks, from a stable square version of the folded wave to freaky PLL-like glitched slides.

Overall results can sound evil at times and sweet at others, a true multi-faced devil.

Size: 12HP
Depth: 31mm
Power: +12V 60ma / -12V 55ma

Notes: Sono Abitus is a high-quality output module. It has a stereo pair of Eurorack-level 1/8" inputs that feed a pair of 14" TRS jacks for line output and a 14" headphone output. The headphone output and line outputs have separate level controls, making it easy to monitor while performing or recording.

Size and power:
4 HP

+12v: 50mA

-12v: 50mA

+5v: 0mA

Sono -- from Latin: "to make a noise"

Abitus -- from latin: "way out, exit"

"Make noises exit"