安全なお買い物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全なお買い物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Synth modules

View:
Options
112/12(ページ1/1)の商品
Subscribe to our weekly Studio Equipment emails
2hp
Cat: 727385 Rel: 02 Oct 19
 
High fidelity audio processor focused on granular synthesis
Notes: 2hp Grain is a high-fidelity audio processor focused on granular synthesis. It's capable of generating granular clouds, microsound phrases, and unique textures that are derived from any input signal. The Density control sets the rate of granularization applied to the input signal and sets its position within the buffer. The Mix control sets the balance between live input and the granular audio stream for dialling in the perfect combination of sounds. In addition, there is a frequency control and associated v/oct input allowing for pitch accurate sequencing of grains. Particle patching has never been smaller with Grain.
Read more
 1 in stock $156.16
Click for better price!
quote 727385
Cat: 745782 Rel: 09 Sep 19
 
Controller unit for the A-155 sequencer
Notes: Module A-154 is a supplement to the A-155 Analog/Trigger Sequencer module. It offers a lot of new features that are not available in the basic control unit of the A-155. The A-154 is used to replace the control unit of one or two A-155, i.e. the section marked "Control" with Start / Stop / Step / Reset buttons and inputs in the upper left corner of the A-155 front panel. If the A-154 is used to control the A-155 the control section of the A-155 is put out of action.

These are the features of the A-154:

Several running modes: forward, backward, pendulum, random, CV controlled step addressing. All modes are available as loop or one-shot.

LED display of the 5 different current modes and one LED for loop/one-shot display

Manual and voltage controlled selection (with attenuator) of the running mode. If no external control voltage is applied one of the 10 modes (5 modes x 2 loop/one-shot) is simply selected with a rotary knob. The CV input with attenuator is used to modulate the running mode with an external control voltage (digital high/low CV to switch between two modes or continuous analogue CV to sweep through different modes). With the combination of manual control and CV with attenuator it is possible e.g. to use only two neighbouring modes (e.g. forward/backward) or sweep through all possible running modes

Manual and voltage controlled selection (with attenuator) of first and last step of the sequence. The range is step 1...8 in 8 step mode resp. 1...16 in 16 step mode

If the running mode "CV Controlled Step Address" is selected the First Step section is used to determine the active sequencer step. Consequently manual and voltage controlled selection (with attenuator) of the active step is possible: the active step can be set by hand with the first step manual control and then modulated by an external control voltage (e.g. LFO, Random, S&H, Theremin, Light CV source, Joy Stick) at the first step CV input (with attenuator).

An internal voltage controlled clock generator with manual and CV control (with attenuator) is available. The output of the clock generator is displayed with a LED and is used as sequencer clock provided that no external clock signal is connected to the Clock In socket (normalled socket). If the CV input of the Clock section is connected to one of the analogue outputs of the sequencer the time for each step can be set separately. Even jumps (or skipping) will be possible as we will introduce the feature that a very short clock pulse will be generated if the control voltage exceeds a certain value. For example the gate row of the A-155 can be used to obtain skipping of steps: the gate output simply has to be connected to the CV input of the A-154 clock generator. If the corresponding switch of the A-155 is set correspondingly in the gate row the step will be skipped.

Manual and voltage controlled (with attenuator) pulse width (PW) of the clock signal. This features can be used to obtain a different gate length for each step: e.g. one of the CV outputs of the A-155 can be used to control the PW. With a PW control voltage coming from a LFO/random/S&H the gate length will change automatically. CV coming from Theremin A-178, ribbon controller A-198, light controlled CV A-179, joy stick A-174 are other ways to control the gate length.

8/16 step mode: A toggle switch us used to select 8 or 16 steps. The "16 step" mode requires two A-155 and one or more voltage controlled switches (e.g. A-150-1 or A-150-8). The voltage controlled switches are controlled by the "A3" output of the A-154. This output remains "low" as long as the active step is in the range 1...8 and turns to "high" in the range 9...16. The voltage controlled switches are used to switch between the CV/trigger/gates outputs of the first A-155 (step 1...8) and the second A-155 (step 9...16). In the A-154 user's manual the corresponding patch is shown.

If two A-155 are used they can work in parallel (8 steps) or serial (16 steps). The 8/16 steps switch determines if the 8 step mode (one A-155 or two A-155 in parallel) or the 16 step mode (two A-155 serial) is chosen. Both modes work with CV controlled step addressing too (see below). In 8 step mode only the steps 1...8 are addressed, in 16 step mode the steps 1...16. For serial operation an additional VC switch (A-150) is required - as mentioned above.
Read more
 1 in stock $167.94
Click for better price!
quote 745782
Cat: 745783 Rel: 09 Sep 19
 
Controller unit for the A-155 sequencer
Notes: Module A-154 is a supplement to the A-155 Analog/Trigger Sequencer module. It offers a lot of new features that are not available in the basic control unit of the A-155. The A-154 is used to replace the control unit of one or two A-155, i.e. the section marked "Control" with Start / Stop / Step / Reset buttons and inputs in the upper left corner of the A-155 front panel. If the A-154 is used to control the A-155 the control section of the A-155 is put out of action.

These are the features of the A-154:

Several running modes: forward, backward, pendulum, random, CV controlled step adressing. All modes are available as loop or one-shot.

LED display of the 5 different current modes and one LED for loop/one-shot display

Manual and voltage controlled selection (with attenuator) of the running mode. If no external control voltage is applied one of the 10 modes (5 modes x 2 loop/one-shot) is simply selected with a rotary knob. The CV input with attenuator is used to modulate the running mode with an external control voltage (digital high/low CV to switch between two modes or continuous analog CV to sweep through different modes). With the combination of manual control and CV with attenuator it is possible e.g. to use only two neighbouring modes (e.g. forward/backward) or sweep through all possible running modes

Manual and voltage controlled selection (with attenuator) of first and last step of the sequence. The range is step 1...8 in 8 step mode resp. 1...16 in 16 step mode

If the running mode "CV Controlled Step Address" is selected the First Step section is used to determine the active sequencer step. Consequently manual and voltage controlled selection (with attenuator) of the active step is possible: the active step can be set by hand with the first step manual control and then modulated by an external control voltage (e.g. LFO, Random, S&H, Theremin, Light CV source, Joy Stick) at the first step CV input (with attenuator).

An internal voltage controlled clock generator with manual and CV control (with attenuator) is available. The output of the clock generator is displayed with a LED and is used as sequencer clock provided that no external clock signal is connected to the Clock In socket (normalled socket). If the CV input of the Clock section is connected to one of the analog outputs of the sequencer the time for each step can be set separately. Even jumps (or skipping) will be possible as we will introduce the feature that a very short clock pulse will be generated if the control voltage exceeds a certain value. For example the gate row of the A-155 can be used to obtain skipping of steps: the gate output simply has to be conneted to the CV input of the A-154 clock generator. If the corresponding switch of the A-155 is set correspondingly in the gate row the step will be skipped.

Manual and voltage controlled (with attenuator) pulse width (PW) of the clock signal. This features can be used to obtain a different gate length for each step: e.g. one of the CV outputs of the A-155 can be used to control the PW. With a PW control voltage coming from a LFO/random/S&H the gate length will change automatically. CV coming from Theremin A-178, ribbon controller A-198, light controlled CV A-179, joy stick A-174 are other ways to control the gate length.

8/16 step mode: A toggle switch us used to select 8 or 16 steps. The "16 step" mode requires two A-155 and one or more voltage controlled switches (e.g. A-150-1 or A-150-8). The voltage controlled switches are controlled by the "A3" output of the A-154. This output remains "low" as long as the active step is in the range 1...8 and turns to "high" in the range 9...16. The voltage controlled switches are used to switch between the CV/trigger/gates outputs of the first A-155 (step 1...8) and the second A-155 (step 9...16). In the A-154 user's manual the corresponding patch is shown.

If two A-155 are used they can work in parallel (8 steps) or serial (16 steps). The 8/16 steps switch determines if the 8 step mode (one A-155 or two A-155 in parallel) or the 16 step mode (two A-155 serial) is chosen. Both modes work with CV controlled step addressing too (see below). In 8 step mode only the steps 1...8 are addressed, in 16 step mode the steps 1...16. For serial operation an additional VC switch (A-150) is required - as mentioned above.

The functions of the Start/Stop/Step/Reset buttons and inputs are the same as for the "old" control unit of the A-155:

A high level at the Start input or operating the Start button starts the sequence from the momentarily addressed step. Not working in "CV controlled step address" mode.

A high level at the Stop input or operating the Stop button stops the sequence (the last active step remains addressed). Not working in "CV controlled step address" mode.
Read more
 1 in stock $161.51
Cat: 744601 Rel: 23 Sep 19
 
Compact three-channel mixer - 6HP
Notes: The "AUTOMIX" module is a compact three-channel mixer for audio or CV sources in the voltage range +-5v (audio modular level).

The mix level of each track can be adjusted and recorded with the track control. The recording time per track is more than one minute. The playback speed is also adjustable.

The recorded track is played back once when the Play button is pressed briefly (one shot) or when the Loop button is pressed a little longer.

In addition, the 3 inputs can be switched separately to +6db audio (for external line level sources) using the slide switch on the rear panel.

All three tracks have a common reset input. The track data remains permanently stored (battery buffered memory).
Read more
 1 in stock $192.54
Click for better price!
quote 744601
Cat: 744602 Rel: 02 Oct 19
 
Dual signal/audio crossmixer
Notes: The "CROSSMIX" module contains two independent crossfaders with two inputs to one output and is designed for audio or CV sources in the voltage range +-5v (Audio Modular Level).

In addition, the 4 inputs can be switched separately to +6db audio (for external line level sources) using the slide switch on the rear panel.

The two crossmix controls can be recorded. The recording time per channel is more than one minute. The playback speed can be adjusted in playback.

The recorded track is played back once when the Play button is pressed briefly (one shot) or in the loop when the button is pressed a little longer.

Both crossfaders have a separate reset input as well as a separate CV input (+-5V ) for controlling the mix e.g. by an LFO.

The track data remains permanently stored (battery buffered memory).
Read more
 1 in stock $192.54
Click for better price!
quote 744602
Cat: 744063 Rel: 12 Sep 19
 
CEM3340 based VCO - 10HP
Notes: CEMosc is here, a stable AS3340 based VCO which tracks beautifully, and is feature rich. Easy to build and calibrate too.

CEMosc features:

- Onboard voltage regulation for tuning and tracking stability
- A rotary octave switch as well as a fine tune knob
- Both manual PW as well as PWM are available
- Linear and Exponential FM inputs, each with attenuators
- Both soft and hard sync
- Sawtooth, Triangle and Pulse outputs
Read more
 1 in stock $190.39
Click for better price!
quote 744063
Cat: 746966 Rel: 12 Sep 19
 
Great sounding VCO for Eurorack - 10HP
Notes: Here's the Roland 100M VCO adapted to Euro. The hard-to-find UA726 has been replaced with a CA3046 with no loss of performance. No hard to find parts whatsoever. The PCB also includes pads for SMD LM3046. It'a the golden age right here.

- A six position rotary switch for octaves gives plenty of range. The PITCH pot is fine tune
- Individual outputs for ramp, square and triangle - an improvement on the original
- Built in chip heater
- Onboard LFO! Yes that's right, an onboard LFO (thanks MC202) for introducing FM and/or PWM
Read more
 1 in stock $190.40
Click for better price!
quote 746966
Cat: 744610 Rel: 06 Sep 19
 
Eurorack receiver for the Wave sensor that allows Wave to connect to modular synthesisers - 4HP
Notes: The Wavefront module is the Eurorack receiver for Wave that allows Wave to connect to modular synthesizers. With Wavefront you can completely bypass the computer and bring unprecedented sound control, effect shaping and manipulation to modular setups.

Use subtle gestures to add vibrato to your favourite lead synth module, or use more visible gestures while performing.

The buttons are great for triggering sequences while the tap lets you interact with percussive modules in a completely new way. Drumming on a table has never been as fun!

To use Wavefront you need one Wave (ring) per module.
Read more
 1 in stock $192.53
Click for better price!
quote 744610
Cat: 739891 Rel: 30 Aug 19
 
Intuitive pitch CV sequencer in 4HP
Notes: Ultra-simple 16-step Eurorack CV sequencer with randomisation option and storage for up to 16 patterns. Straight to the point business, all in just 4HP of rack space.

Supplier notes:
Small, easy-to-program sequencers are a bit of a rarity. Vox Digitalis is our answer to this issue. With intuitive displays and simple controls, VD is perfect for all your pitch CV needs. Set your sequence length, dial in each note, randomize, save and load 16 sequences -- VD does all the stuff the big sequencers do, just in 4HP.
Read more
 1 in stock $174.35
Click for better price!
quote 739891
Cat: 732313 Rel: 11 Sep 19
 
Portable power source interface for Eurorack
Notes: Release your mind and release your modular system, with the Polyend Anywhere power compatibility Eurorack module. The Polyend Anywhere hooks up to any Power Bank battery to allow the user the liberty of portability with their modular system. Take your system for a walk! Smell the flowers, and use the inspiration to create the simultaneous feedback/AM/FM patch you've been dreaming of!
Read more
 5 in stock $158.31
Click for better price!
quote 732313
Cat: 743613 Rel: 23 Sep 19
 
Clean/character auto compressor & distortion - 4HP
Notes: Autodyne is a 4hp auto-compressor/distortion featuring a multi-mode side chain filter and NY style parallel compression blend control.

Ratio, Threshold and Gain are all built into a single, simple to use COMP control. Compression gets more extreme as this control is swept past centre position. Setting below centre offers more subtle/typical compression.

Autodyne Automatically Responds to Transients, will glue a mix with ease and dial in the perfect feeling of the program material you feed into it.

GAIN CONTROL to trim the final output gain or offer up some extremely brutal distortion, whichever you prefer.

Switchable Side Chain Filter is provided along with a triple slope high pass filter, in order to retain lower frequency content and unwanted over-compression by removing them from the Side Chain. Input signal is normalized into the Side Chain or an external signal may be utilized via the Side Chain Input.

Parallel Compression BLEND Control mixes the unaffected input signal with the compressed output for even further control of your sound. Compression may be bypassed simply by sweeping this control to minimum position.

Controls are simple enough to match in tandem for dual unit, stereo operation, if desired.

Audiophile grade discrete components and Burr-Brown op amps used throughout.
Read more
 1 in stock $190.40
Click for better price!
quote 743613
Cat: 744597 Rel: 27 Aug 19
 
6HP power supply for guitar pedals, plus two small signal splitters
Notes: Stoker Elektrek is equipped with a 2.1 mm hollow connector to supply power to effect pedals. A short adapter cable is included. The module itself draws power from the modular PSU. A look at the other technical data reveals that Stoker Elektrek is compatible with many effect pedals:

- 9V DC power supply
- Up to 750 mA
- Polarity: peak = negative / ring = positive

On top of that, Stoker Elektrek offers two mini multiples, each with one signal input and two outputs, which can also be used as a large splitter.
Read more
 1 in stock $188.25
Click for better price!
quote 744597
112/12(ページ1/1)の商品

Filter

Synth modules
DJ機器
Release Date
Featured
Close