Synth modules

Notes: SQUEEZE2 is the improved variant of SQUEEZE:

- SMD transistors are changed to matched through hole ones
- all capacitors are now through hole Panasonic LowESR
- added trimming circuit to adjust 0 gain for the center of make-up gain pot so the SQZ will have 0 amplification on middle adjustments

4HP Compressor designed for continuous adjustment of gain, threshold and compression ratio with a single potentiometer.

There is also a knob for input level and a knob for make-up gain.

The module is based on high-performance THAT4305 Blackmerr VCA chip.

Tech specs:

-width 4HP
-35mm depth behind the panel, including the power connector
-1 audio input : IN
-1 audio level pot : INPUT
-2 control pots : LESS/MORE (compression), MAKE-UP Gain
-1 output : OUT
-standard 10 pin euro power +12V / -12V
-power consumption +12V 25mA -12V 25mA

Notes: The STATIC module is a comprehensive collection of noise sources generated with different methods.

Tech specs:

-width 10HP
-38mm depth behind the panel, including the power connector
-2 control pots : MORPH, SPECTRUM
-1 switch : spectrum type TR/CHIP
-8 outputs : MSWHITE, MSPINK, ZNWHITE, ZNPINK,
DARK, MORPH, TROUT, RNDVOLT
-standard 10 pin euro power +12V / -12V
-power consumption +12V 35mA , -12V 30mA

Notes: As the name suggests this module can produce sub frequencies of -1 and -2 octaves relative to the square wave signal provided at the input jack.

But this is not just a simple SUB generator. It also has a little mixer that will let you add different levels of -1 and -2 octave signals to the original square wave. You can select the -2 octave signal to be a square wave or a pulse wave.

The module has individual outputs for the mixed signal, the -1 octave and the -2 octave.

This little modules can produce enough timbral variation to make you bass sound exciting.

Tech specs:

- 4HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 12mA , -12V 9mA

Notes: VCA2600 needs no introduction. The best sounding VCA in 4HP with matched and thermo coupled transistors.

Tech specs:

-width 4HP
-35mm depth behind the panel, including the power connector
-standard 10 pin euro power +12V / -12V
-power consumption +12V 25mA -12V 25mA

Notes: This filter is based on the classic 2600 from the seventies and uses the LM3900 Norton opamp chip.

It has an audio inputs, two CV ins and an audio out.

You can control audio input level, CV levels, frequency cutoff and resonance.

It has a beautiful sound and it can go from relatively clean to dirty and screamy depending on audio signal level and resonance.

Tech specs:

- 8HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 7mA , -12V 13mA

Notes: The VCZIII voltage controlled oscillator modules are Feedback's latest creation and are based on the VCOs of one of the most revered analog instruments, the famous British pin matrix synth released in 1969.

The VCZIII series VCO is a result of the collaboration of Feedback modules and CMS-LAB and is a modern re-creation of those temperamental, organic and beautiful sounding VCOs from 1969 but with enhancements and adaptations to the Eurorack needs of 21st century.

There are two type of VCOs, VCZIII A based on VCO1 with variable shape SINE & SAW waveforms, VCZIII B based on VCO2 & VCO3 with variable TRIANGLE & PULSE waveforms.
Also, each VCO comes in two versions, one with normal fine tune potentiometers and one with precision multiturn potentiometer.

THIS VERSION IS WITH NORMAL FINE TUNE POTENTIOMETER.

Tech specs:

- 12HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 50mA , -12V 30mA

Notes: The VCZIII voltage controlled oscillator modules are Feedback's latest creation and are based on the VCOs of one of the most revered analogue instruments, the famous British pin matrix synth released in 1969.

The VCZIII series VCO is a result of the collaboration of Feedback modules and CMS-LAB and is a modern re-creation of those temperamental, organic and beautiful sounding VCOs from 1969 but with enhancements and adaptations to the Eurorack needs of 21st century.

There are two type of VCOs, VCZIII A based on VCO1 with variable shape SINE & SAW waveforms, VCZIII B based on VCO2 & VCO3 with variable TRIANGLE & PULSE waveforms.

Also, each VCO comes in two versions, one with normal fine tune potentiometers and one with precision multiturn potentiometer.

THIS VERSION IS WITH BOURNS MULTITURN FINE TUNE POTENTIOMETER.

Tech specs:

- 12HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 50mA , -12V 30mA

Notes: The VCZIII voltage controlled oscillator modules are Feedback's latest creation and are based on the VCOs of one of the most revered analog instruments, the famous British pin matrix synth released in 1969.

The VCZIII series VCO is a result of the collaboration of Feedback modules and CMS-LAB and is a modern re-creation of those temperamental, organic and beautiful sounding VCOs from 1969 but with enhancements and adaptations to the Eurorack needs of 21st century.

There are two type of VCOs, VCZIII A based on VCO1 with variable shape SINE & SAW waveforms, VCZIII B based on VCO2 & VCO3 with variable TRIANGLE & PULSE waveforms.
Also, each VCO comes in two versions, one with normal fine tune potentiometers and one with precision multiturn potentiometer.

THIS VERSION IS WITH NORMAL FINE TUNE POTENTIOMETER.

Tech specs:

- 12HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 50mA , -12V 30mA

Notes: The VCZIII voltage controlled oscillator modules are our latest creation and are based on the VCOs of one of the most revered analogue instruments, the famous British pin matrix synth released in 1969.

The VCZIII series VCO is a result of the collaboration of Feedback modules and CMS-LAB and is a modern re-creation of those temperamental, organic and beautiful sounding VCOs from 1969 but with enhancements and adaptations to the Eurorack needs of 21st century.

There are two type of VCOs, VCZIII A based on VCO1 with variable shape SINE & SAW waveforms, VCZIII B based on VCO2 & VCO3 with variable TRIANGLE & PULSE waveforms.

Also, each VCO comes in two versions, one with normal fine tune potentiometers and one with precision multiturn potentiometer.

THIS VERSION IS WITH BOURNS MULTITURN FINE TUNE POTENTIOMETER.

Tech specs:

- 12HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 50mA , -12V 30mA

Notes: The Airlectron Sensor Recorder module is equipped with a sunlight independent distance sensor to generate CV output voltages.

A distance sensor reacts to hand movements and varies the CV output voltages (bipolar/max +/- 5 V, unipolar/max 0-+10 V). The range control adjusts the detection distance (2-50 cm). The freeze function keeps the voltage when there is no continuous movement.

The recorder/looper can be used to record motion sequences for up to two minutes. This recorded data can be played back in a loop or once and restarted at the START/RESET input. LEDs indicate the status of the gate inputs and outputs.

Features:

3x controller
1x Vishay distance sensor
3x gate/trigger in- and outputs
2x CV outputs unipolar/bipolar
Power supply via Doepfer connector

Notes: The C-1U module is a one-channel module for recording and playing back movements of controller. Those can be recorded with channel's knob. The movements will be output as control voltage. The record time amounts to one minute maximal.

The track can be played once only (one shot) or in loop. The speed of the play back or the output offset is controllable with the pot. There are an additional CV input for CV recordings and a reset input.

The track data remains permanently stored when a 3V battery is used to buffer the RAM. When the module is switched on, the recorded data is available again. The module can be operated unipolar or bipolar (set by jumper on the back).

Note: The C-1U KnobRekorder uses a standard 3v lithium backup battery , type CR2032. The battery is needed to keep recordings and settings stored when the Eurorack case is turned off.

Dimensions: 12 HP
Power consumption: 20mA at +12 V and 9mA at -12 V

Module is a 1U tile.

Notes: Up to eight voices of digitally synthesised drums, percussion and synth sounds from this versatile module, featuring virtual analogue models as well as FM and wavetable options.

Supplier's Notes:
Flame "Fire" percussion synth module

The module is a full 8-way polyphonic drum and percussion synthesizer. It offers different digital synthesis algorithms, which can be distributed over 8 channels. The sound engine delivers virtual analog sounds as well as different digital percussion sounds, which are generated with FM, wavetable or virtual analog synthesis. It is also possible to create sim- ple monophonic bass or synthesizer voices.

During development, particular attention was paid to direct and simple usability with regard to live operation. The hardware essentially consists of two parts (which are deli- vered together). On the one hand there is the basic module with all controls, the display, connections for MIDI, 2x CV inputs and 5 audio outputs.

There is also a separate XFIRE I/O extension with sockets for the 16 analog trigger/gate/CV inputs and 3 additional audio outputs. Both modules are connected via a 60cm long ribbon cable. In this way, the XFIRE module can be installed anywhere else in the rack. The base module is therefore only 22TE wide and can also work alone without the extension as a MIDI expander.

A maximum of 8 audio outputs are available. A stereo pair (outputs 7+8), plus 6 additio- nal individual direct outputs. All outputs are freely configurable. Two pages with settings for panorama and volume are available for the stereo main out.

There is a gate/trigger input and a configurable CV input for each channel. Two additio- nal programmable CV inputs can be used for further controls. Regardless of the analog connection, the module offers full MIDI functionality. Two MIDI inputs and a MIDI output/softthru allow integration into an external MIDI setup. The firmware can be upda- ted via MIDI Sysex. The created KIT data can also be saved or exchanged.

Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


Up to eight voices of digitally synthesised drums, percussion and synth sounds from this versatile module, featuring virtual analogue models as well as FM and wavetable options.

Supplier's Notes:
Flame "Fire" percussion synth module

The module is a full 8-way polyphonic drum and percussion synthesizer. It offers different digital synthesis algorithms, which can be distributed over 8 channels. The sound engine delivers virtual analog sounds as well as different digital percussion sounds, which are generated with FM, wavetable or virtual analog synthesis. It is also possible to create sim- ple monophonic bass or synthesizer voices.

During development, particular attention was paid to direct and simple usability with regard to live operation. The hardware essentially consists of two parts (which are deli- vered together). On the one hand there is the basic module with all controls, the display, connections for MIDI, 2x CV inputs and 5 audio outputs.

There is also a separate XFIRE I/O extension with sockets for the 16 analog trigger/gate/CV inputs and 3 additional audio outputs. Both modules are connected via a 60cm long ribbon cable. In this way, the XFIRE module can be installed anywhere else in the rack. The base module is therefore only 22TE wide and can also work alone without the extension as a MIDI expander.

A maximum of 8 audio outputs are available. A stereo pair (outputs 7+8), plus 6 additio- nal individual direct outputs. All outputs are freely configurable. Two pages with settings for panorama and volume are available for the stereo main out.

There is a gate/trigger input and a configurable CV input for each channel. Two additio- nal programmable CV inputs can be used for further controls. Regardless of the analog connection, the module offers full MIDI functionality. Two MIDI inputs and a MIDI output/softthru allow integration into an external MIDI setup. The firmware can be upda- ted via MIDI Sysex. The created KIT data can also be saved or exchanged.

Notes: The module can record the joystick movement up to a length of over a minute. The sequence remains stored in the battery-backed RAM after switching off. When playing the sequence, it can be manipulated in speed and playback direction.

There is a FREEZE function to hold the current joystick position plus an external reset input. In addition, a GATE is set during movement and a CV voltage is output as a function of the joystick movement. The ranges of the X / Y output voltages are bipolar +/- 5v or unipolar from 0 to + 10v. Both channels X and Y have a passive attenuator potentiometer, so that the voltage range can also be set lower.

Notes: The "uMCLK Divider" module can either work as a MIDI clock divider or as an analog clock divider. The divider outputs are assigned differently in both operating modes.

After receiving a MIDI start command, the module works as a MIDI clock divider. There are fixed dividers on 11 outputs. Via the divider output KEYS, triggers can be triggered and mixed via MIDI notes. The keyboard zone extends over three octaves. With the help of the LEARN key, the receive MIDI channel and the lowest note of this 3-octave range can be defined.

When stopped (i.e. after receiving a MIDI stop command or after switching on), the module works as an analog clock divider and divides the analog clock present at the CLOCK input. The 12 analog divider outputs can be reprogrammed via SYSEX. Ready-made SYSEX files are already available (e.g. for even / odd dividers, Fibonacci series, offbeats, etc.). The RESET input resets the analog counters or serves to deactivate the analog divider.

Connections:
- Ribbon cable adapter for Doepfer bus +/-12Volt
- Inputs: 2x Clock/Gate,Reset (0/+5..10V), 1/8th inch mono jacks
- 1x MIDI (TRS-B standard) 1/8th inch stereo jack Outputs: 1x MIDI (TRS-B standard) 1/8th inch stereo jack
- 14x Clock/Gate Divider, 1/8th inch mono jacks

Control elements:
- 1 push button with LED (LEARN key) 16 LED's
- Current consumption: max. +70..80mA / - 0 mA
- Size: Euro rack format 3U / 6HP 30x128,5x40 mm

Dimensions
5 HP
40 mm deep

Current Draw
80 mA +12V

Notes: The "uMM" combines a MIDI merger and two independent THRU distributors in a module that is only 4 HP wide. All sockets on the module are in MIDI TRS-B format.

At the heart of the two-input MIDI merger is a small, powerful ARM processor with plenty of buffer memory. Two MIDI streams are mixed to one output and can also be tapped via an additional second output. Two LEDs signal the operation of the merger: one LED indicates MIDI activity at the inputs, and a second LED warns of too much data at the inputs.

The second group of functions consists of two independent, separate MIDI THRU distributors. The MIDI data at the respective MIDI input can be picked up and distributed at the three THRU outputs. If required, a 1-to-5 distributor can be created from the two units by connecting an output of the left group to the input of the right group.

Features:

4x MIDI IN (TRS-B)
2x MIDI-OUT (TRS-B)
6x MIDI-THRU (TRS-B)
Powered via Doepfer connector

Notes: Alter is an effects processor for Eurorack format. There are two versions of the Alter which are visually identical except the names "Alter 1" and "Alter 2". This is Alter 1. Internally, 1 & 2 have an entirely different set of effects from the other. Each version features 7 unique and meticulously designed DSP effects.

Control

- Controls for mix, X, Y and Sift as well as clock.
- All effects have a variation of a filter which may change effect to effect.
- X and Y control various rates, feedback and time over the different effects (note that some of the images shows a prototype which says "rate" under two of the pots. The faceplate has been changed to X and Y).
- Clock control adjusts the rate which controls the DSP which can drastically change the effect. In doing so it does slightly lower the quality of the output signal but the results are fantastic. This clock is not for synchronization.
- Mix, X, Y and Sift all have CV control inputs.
- Each control level or CV input is visualized on the control panel.

Ins and outs

- Stereo inputs with separate level/gain control for right and left channels. These levels can also act as mute as it can take the signal to 0. They can also add gain to a quiet signal.
- Peak level indicator for clipping levels at the input
- Mono input is made stereo within the DSP and outputs to both left and right channels
- Stereo outputs for right and left channels

Effects

The effect is selected by the hexagonal touch pad. The effects for Alter 1 are as follows:
1 - long delay
2 - tight, notated granular delay
3 - plate reverb
4 - shimmering reverb
5 - distortion multi-filter
6 - pitch delay
7 - stutter glitch

Specs

Includes printed manual
+12V: 160mA
-12V: 0mA
+5V: 0mA
16HP width
25 mm Depth

Notes: Alter 2 is an effects processor for Eurorack format. There are two versions of the Alter which are visually identical except the names "Alter 1" and "Alter 2". This is Alter 2. Internally, 1 & 2 have an entirely different set of effects from the other. Each version features 7 unique and meticulously designed DSP effects.

Control

- Controls for mix, X, Y and filter as well as clock.
- All effects have a variation of a filter which may change effect to effect.
- X and Y control various rates, feedback and time over the different effects.
(note that some of the images shows a prototype which says "rate" under two of the pots. The faceplate has been changed to X and Y.)
- Clock control adjusts the rate which controls the DSP which can drastically change the effect. In doing so it does slightly lower the quality of the output signal but the results are fantastic. This clock is not for synchronization.
- Mix, X, Y and filter all have CV control inputs.
- Each control level or cv input is visualized on the control panel.

Ins and outs

- Stereo inputs with separate level/gain control for right and left channels. These levels can also act as mute as it can take the signal to 0. They can also add gain to a quiet signal.
- Peak level indicator for clipping levels at the input.
- Mono input is made stereo within the DSP and outputs to both left and right channels.
- Stereo outputs for right and left channels.

Effects

The effect is selected by the hexagonal touch pad. The effects for Alter 2 are as follows:
1 - Analogue delay
2 - Reverb with infinite capture and LP + HP filters
3 - Choral reverb
4 - Palindrome reverse delay - backward/forward repeat
5 - Time stretch
6 - Pitch shift (notated semi-tones)
7 - Time stretch glitch

Specs

Includes printed manual
+12V: 160mA
-12V: 0mA
+5V: 0mA
16HP width
25 mm Depth

Notes: The 333 is a summing and distribution module for Eurorack modular systems.

It is composed of three identical sections, the red, yellow and green, each of those featuring three inputs summing amplifier with three independently buffered outputs.

Derived directly from the CGM creative mixer series, the sum section is DC coupled, allowing the sum of control voltages as well as audio signals.

With an extremely low tolerance in both sum and output sections, it is suitable also for summing quantized voltages like the ones coming out from the quantized outputs of the SAPEL.

In case CVs or audio signals are particularly hot, the 6dB attenuator might be helpful to reduce exactly by 50% the incoming signals.

Red and yellow output are also normalled to the 1st jack socket of the yellow and green input: in this way this module can also work as a 1 to 9 buffered multiple.

Notes: Oof. Frap casually serve up one of the best filters we've seen in a long time. Quad multimode circuits with saturation and feedback give you extensive routing options. Delicious.

Supplier's Notes:
cunsa /'cu?nsa/ s.f. [dialect of Modena of uncertain etymology, probably from a Latin *comptiare, derived from comptus, participle of comere 'organize,' 'decorate'] i curing, seasoning (of foods), tanning (of leathers).

Seasoning is crucial for cooking. It is a process that enhances the flavors, glues the ingredients together, and even adds some unexpected kick.

From a gentle refining touch to a shovelful of spice, CUNSA is the perfect seasoning tool for your patches. It can sweeten a sour lead or beef up an insipid bass line, and anything in between.

And, just like a good oil, you can even taste it by itself!

CUNSA is a quadruple analog pingable multimode resonant filter, saturator, mixer, and oscillator.

It is Frap Tools' sound seasoning tool: it can gently even a patch, applying a final touch, or it can set it on fire with a ridiculous amount of spice. It's up to you and your cooking style!

It consists of four multimode resonant filters with a custom saturation and feedback control that you can use independently or in various combinations and roles thanks to a series of seminormalizations.

Four Analogue Resonant Multimode Filters

CUNSA features four state-variable filters that can be used independently or linked and mixed. Each filter provides three behaviors simultaneously: lowpass, bandpass, and highpass. Each behavior has a 12 dB/oct slope, except for the lowpass, which can be either 12 or 24 dB/oct.

Unique 'Character' Circuit for Feedback and Distortion

CUNSA handles feedback and gain staging with extreme control and versatility. Besides the usual Q control that emphasizes the cutoff frequency, the Character circuit defines the amount of soft clipping when the filter overloads. High clipping guarantees a controlled behavior with fat tone and pure resonance, while low or no clipping lets the signal saturate the filter stages and make it scream.

V/oct Tracking and Quadruple Oscillator

Each filter responds to the V/oct signal with excellent tracking. It is thus possible to move the cutoff frequency along with the main melody or make CUNSA resonate with no input and transform it into a multiple oscillator. The V/oct inputs are seminormalled so you can control more filters with the same CV. Easy chords stabs!

Ping and Ring

CUNSA is ideal for percussive and organic tones. The Ping circuit offers a behavior similar to the BRENSO but AC-coupled. Instead of shooting the frequency to the moon with any trig, CUNSA gently responds to different incoming gates with a selectable decay curve. The Ping circuit can thus create natural decay sounds when fed with trigs or smoother envelopes with any other voltage, like a linear integrator with a custom decay.

Besides this, you can also feed the filter's audio input with trigs and make it ring at high Q settings.

Linked or Individual Filtering

The four filters can work independently or arranged in groups through seminormalled inputs and sum outputs. CUNSA can thus be a 4×1, 2×2, or a massive 1×4 filter. Even odd configurations are possible, like 1+2+1 or 3+1. Mono, stereo, or quadraphonic audio is at your fingertips.

Filter and Combo Behaviour

When the filter behavior is set to COMBINED, every control of the cutoff frequency also affects the input VCA, reducing the signal amplitude and saturation as it approaches the lowest range. It can make organic decays with the ping circuit or tame the low range at high Q and Character settings.

Four Seminormalizations for Group Use

Four inputs have a cascaded seminormalization: audio inputs, VCA CV, V/oct, and Ping. Every signal patched to a filter will thus feed also those at its right, making simultaneous use even simpler. To remove a seminormalization, simply patch a dummy cable to the corresponding input.

Analog Mixing Stage and Group Outputs

Every filter output can be routed to an analogue mix bus that sums the four filters and outputs them in three combinations: all, 1+2, and 3+4. These outputs allow for versatile audio processing. Just like we did with FUMANA, we added a gentle shelving EQ for the higher frequencies of the All output to provide additional timbral variety.

CV Inputs with Attenuators

Besides the seminormalled inputs, every filter features additional CV inputs for cutoff frequency, Q, and Character, each with a dedicated attenuverter.

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Oof. Frap casually serve up one of the best filters we've seen in a long time. Quad multimode circuits with saturation and feedback give you extensive routing options. Delicious.

Supplier's Notes:
cunsa /'cu?nsa/ s.f. [dialect of Modena of uncertain etymology, probably from a Latin *comptiare, derived from comptus, participle of comere 'organize,' 'decorate'] i curing, seasoning (of foods), tanning (of leathers).

Seasoning is crucial for cooking. It is a process that enhances the flavors, glues the ingredients together, and even adds some unexpected kick.

From a gentle refining touch to a shovelful of spice, CUNSA is the perfect seasoning tool for your patches. It can sweeten a sour lead or beef up an insipid bass line, and anything in between.

And, just like a good oil, you can even taste it by itself!

CUNSA is a quadruple analog pingable multimode resonant filter, saturator, mixer, and oscillator.

It is Frap Tools' sound seasoning tool: it can gently even a patch, applying a final touch, or it can set it on fire with a ridiculous amount of spice. It's up to you and your cooking style!

It consists of four multimode resonant filters with a custom saturation and feedback control that you can use independently or in various combinations and roles thanks to a series of seminormalizations.

Four Analogue Resonant Multimode Filters

CUNSA features four state-variable filters that can be used independently or linked and mixed. Each filter provides three behaviors simultaneously: lowpass, bandpass, and highpass. Each behavior has a 12 dB/oct slope, except for the lowpass, which can be either 12 or 24 dB/oct.

Unique 'Character' Circuit for Feedback and Distortion

CUNSA handles feedback and gain staging with extreme control and versatility. Besides the usual Q control that emphasizes the cutoff frequency, the Character circuit defines the amount of soft clipping when the filter overloads. High clipping guarantees a controlled behavior with fat tone and pure resonance, while low or no clipping lets the signal saturate the filter stages and make it scream.

V/oct Tracking and Quadruple Oscillator

Each filter responds to the V/oct signal with excellent tracking. It is thus possible to move the cutoff frequency along with the main melody or make CUNSA resonate with no input and transform it into a multiple oscillator. The V/oct inputs are seminormalled so you can control more filters with the same CV. Easy chords stabs!

Ping and Ring

CUNSA is ideal for percussive and organic tones. The Ping circuit offers a behavior similar to the BRENSO but AC-coupled. Instead of shooting the frequency to the moon with any trig, CUNSA gently responds to different incoming gates with a selectable decay curve. The Ping circuit can thus create natural decay sounds when fed with trigs or smoother envelopes with any other voltage, like a linear integrator with a custom decay.

Besides this, you can also feed the filter's audio input with trigs and make it ring at high Q settings.

Linked or Individual Filtering

The four filters can work independently or arranged in groups through seminormalled inputs and sum outputs. CUNSA can thus be a 4×1, 2×2, or a massive 1×4 filter. Even odd configurations are possible, like 1+2+1 or 3+1. Mono, stereo, or quadraphonic audio is at your fingertips.

Filter and Combo Behaviour

When the filter behavior is set to COMBINED, every control of the cutoff frequency also affects the input VCA, reducing the signal amplitude and saturation as it approaches the lowest range. It can make organic decays with the ping circuit or tame the low range at high Q and Character settings.

Four Seminormalizations for Group Use

Four inputs have a cascaded seminormalization: audio inputs, VCA CV, V/oct, and Ping. Every signal patched to a filter will thus feed also those at its right, making simultaneous use even simpler. To remove a seminormalization, simply patch a dummy cable to the corresponding input.

Analog Mixing Stage and Group Outputs

Every filter output can be routed to an analogue mix bus that sums the four filters and outputs them in three combinations: all, 1+2, and 3+4. These outputs allow for versatile audio processing. Just like we did with FUMANA, we added a gentle shelving EQ for the higher frequencies of the All output to provide additional timbral variety.

CV Inputs with Attenuators

Besides the seminormalled inputs, every filter features additional CV inputs for cutoff frequency, Q, and Character, each with a dedicated attenuverter.

Notes: The Falistri is a fully analogue multi-purpose movement manager designed to generate and edit voltages to easily accomplish any patch.

The module can be divided into two big parts: in the upper two-thirds of the panel take place two specular function generators, while the lower third is composed of a dual cascaded frequency divider, a linear slew limiter, and a four-quadrant multiplier.

Key features:

Two Function Generators: Envelopes, LFOs, Oscillators
Adjust the Shape Without Changing the Time
Exclusive Shapes per Stage
Trig Buttons: Play Those Envelopes!
Three Play Modes (Voltage-Selectable)
Interacting Functions: Quadrature Mode
All the Outputs, Everywhere
Cascaded Frequency Dividers
Four-Quadrant Multiplier
Linear Slew Limiter

Size 18 HP
Depth 38 mm

Current draw
170 mA @ +12 V
170 mA @ -12 V

Notes: The FUMANA is an all analog dual filter bank with various control to access dynamically these bands. Each filter bank is composed of an array of 16 independent 48dB/oct bandpass filters. Having two identical filter arrays, allows you to use one of those for spectral analysis (of a modulator signal) and the other for spectral re-synthesis (of the main signal). Each array is sub-grouped in odd and even bands (numbering these increasingly from 1 to 16 from left to right). It is possible to apply different signal to odd and even bands, both for main and/or modulator arrays. This, together with the 16 envelope followers connected to each band of the modulator filterbank, and the 16 VCA connected to each band of the main filterbank, allows the FUMANA to perform a single 16 bands or a dual 8 bands analog spectral transfer.

While the upper section provide access to each main filter's direct output, the lower section has 4 voltage controllable parameters to manage two independent functions for further spectral editing: tilt and parametric scan.

The tilt, as the name suggest, tilts the spectrum, adding and subtracting amplitude to the 16 bands, emphasizing lower or high bands, and attenuating high or lower bands: this is managed only with the green potentiometer.

The parametric scan, instead, works with three parameters: peak/notch, band selector and width. Like in a parametric equalizer, where is possible to set peak/notch gain, frequency and slope, the FUMANA uses three parameters to set which is the centre band to perform this manipulation, then if that band should be emphasized or attenuated, and how this action is extended to nearby bands.

In addition to the 16 bandpass outputs, there are other 4 outputs provided: the all bands output, the all envelope followers output, the odd bands and the even bands output. These two have the options to be inverted in phase with two switches, in order to obtain even more combination when summed together, maybe/also with the "all bands output", using, for example the 333 module.

Since a spectral transfer tool may be used as a "vocoder-like-effect", the FUMANA provides an input for an external noise which may be used for unvoiced (fricative/sibilants) sounds as words containing or starting with s, f, z, ch and other fricative sounds.

Notes: Designed for Frap's CGM Creative Mixer modules, the Masterone takes an input via IDC socket rather than standard Eurorack connections, then feeds out to headphone outs, balanced stereo XLR, TRS and mono.

Supplier's Notes:
The Masterone is the first Frap Tools module designed to be connected exclusively with non-Eurorack equipment.

It features four separate output sections with different Neutrik connectors and adjustable gain levels to suit the most common live and studio situations (and even some uncommon ones).

With no inputs and just large-format outputs, it pushes even further the concept behind the M module: being a Eurorack system's gateway to the outside world.

XLR Balanced Stereo Outputs

Two XLR connectors (left and right) provide a balanced output with the expected 6 dB extra gain. In many cases, they can allow bypassing a DI box.

TRS Pseudo-Balanced Stereo Outputs

These outputs are very similar in concepts to the ones on the M module, but with large 1/4" jack connectors. It is possible to patch standard TS cables and use them as unbalanced outputs, or use TRS cables to interface them with balanced equipment (the ground is routed to both the ring and the sleeve, for a better performance than regular unbalanced outputs).

Attenuation Switches for Flexible Connectivity

If the two stereo outputs are too hot, a set of switches can attenuate them. The Line/Mic switch on the XLR outputs attenuates them by ~30 dB, while the Line/Inst switch on the TRS outputs attenuates them by ~15 dB.

Stereo Headphones Output with Pre-Fader Listening

The Headphones section allows you to monitor the Master output with an independent volume knob and, at the same time, take advantage of the PFL function on the Channels and the Groups. Rotate the PFL crossfader towards the blue section to blend the PFL modules with the Master sum and check if everything is okay before launching the next scene.

Mono Output with Dedicated Fader

Should you need an extra monitor on stage, or run the whole system through a vintage amp in the studio for parallel processing, the auxiliary monophonic outputs is the answer. It provides the sum of both channels in a handy, pseudo-balanced output with a dedicated fader: attenuate the line level by 15 dB, or amplify it by 6 dB.

12-LED VU Meter with Memory

A detailed VU Meter monitors the signal amplitude from -40 to +15 dB with peak memory on the upper LEDs.

Dimensions:

12HP

38 mm deep

85 mA +12V - 80 mA -12V

with headphones at high level (250O)

110 mA +12V 105 mA -12V

Notes: The SAPEL is a random control voltages source for Eurorack modular systems. It is composed of two main sections, one that generates audio noises, in 4 different versions, and another which includes two specular random clock, random voltages and clock sources.

Noise outputs are colour coded, based on the noise colours, and include:

- Blue (+3dB/oct spectrum)
- White noise (0dB/oct spectrum)
- Pink noise (-3dB/oct spectrum)
- Red noise, a.k.a. Brown or Brownian (-6dB/oct spectrum).

The random voltage and clock section features four uncorrelated random CV generation paths, divided in;

- Fluctuating random voltage;
- Quantized random voltage with 2n stages tuned in semitones referred to 1V/oct scale;
- Quantized random voltage with n+1 stages tuned in octaves referred to 1V/oct scale;
- Non quantized sample & hold.

It is also possible to set a probability distribution with a potentiometer, and apply (or do not apply) the chosen distribution setting to each of the four paths independently.

Furthermore, each of the two random sources section features an independent built-in clock generator, with clock output and random clock output, which can be used in "more than" or "less than" mode. It is possible to use an external clock signal as a clock source, bypassing the built-in one. In addition to that, it is also possible to hand trigger the clock via a manual sample & hold button, which can be also modulated by gate signals.

Notes: The SC (Stereo Channel) is a single-channel stereo module for the CGM Eurorack mixer, fully compatible with every other product of this family.

It features a mono/stereo local output which makes it ideal for multitrack recording and advanced parallel processing.

Thanks to its advanced I/O configuration, it can work as stereo-to-stereo, mono-to-mono, mono-to-stereo, and stereo-to-mono.

The gain control and the two mono FX sends can work in pre or post-fader mode, and the pan pot can also work as a dual mono crossfader, making it suitable for blending two mono sources into a single mono sum.

All the parameters are voltage-controllable for creative mixing automation.

Mechanical mute, PFL, and Solo-in-Place complete the feature set suitable both for studio and live performances.

*The SC replaces the C as the primary single-channel CGM solution. The C module is now discontinued.

Notes: USTA is a 4×4 tracks sequencer for voltages and gates with variable stage duration, designed to quickly see and edit multiple voltage relationships in real time.

Variable stage duration means that every single stage duration can be individually set in relation to the clock, instead of being constrained to a one-to-one ratio (i.e. one stage per every clock impulse).

4×4 tracks means that every stage can store and generate up to four separate voltages (two CVs and two gates), and that up to four independent stage sequences can be arranged into as many different tracks.

Its architecture is based on an array of 16 'Stages' which form a 'Pattern'; 16 patterns form a 'Track', and four tracks form a 'Project'. Within each track, each stage can provide two gates and two CVs, and a wide set of options is available to define and modify the value of each output ('Layers') and the way it is played ('Colours').

Every Stage is related to a dedicated stepped encoder for quick and intuitive editing, and all the 16 encoders are arranged in an oval layout with a circular playhead. Every encoder is surrounded by a ring of 16 LEDs and a RGB led, to provide a visual feedback of the current setting of that step basing on the layer you are working on (like raw CV, quantized CV, length, gate...) and the way it should play depending on the RGB colour.

Notes: Advanced generative sequencer featuring mutes per channel and transposition facilities.

Akropoli is an extension and enhancement of our successful Little Melody and High Towers modules, offering the features of both of these modules as well as some of it's own unique features such as mute buttons per channel, manual transpose knob and 1V/oct transpose CV input. Akropoli operates using Frequency Central's proprietary TOOL V2 code, and can count in integers as well as multiples for even more subtle and evolving variations.

Akropoli is a generative sequencer based around clock divisions and a chromatic quantiser, used to create in-the-moment licks and riffs. It is more that the sum of it's parts.

Akropoli's internal operations can be considered as 4 clock dividers patched into a CV mixer via attenuators. The attenuators select notes over a 5 octave range, the clock dividers determine how often those notes are added to the mix. The final output of Akropoli is quantized chromatically for fast set up and continuously pleasing results. Akropoli has an onboard transposition knob, as well as a 1V/oct transposition CV input.

The 4 clock dividers are labelled A, B, C, and D. They all receive clocks from the same source, the divisions may be selected using the presets and the individual division selectors. The clock dividers can be set to count up, down, or to one of a variety of modes that move between counting up and down. For further information on Presets and Modes see the Little Melody User Guide.

Additionally, each clock divider has it's own binary output (either high or low), these 4 outputs can be used to clock/gate/trigger other stuff on other modules to great effect.

Product Specifications

12V draw
50mA

-12V draw
36mA

5V draw
0mA

Depth
35mm

Notes: Looking Glass is an 5 x 5 active patchbay/matrix mixer/switcher for both audio and control voltages. It features:

5 inputs (1 through to 5), each with attenuators
5 inverted outputs (A through to E) which are 180o out of phase with the inputs
5 normal outputs (A through to E) which are in phase with the inputs
A switch matrix of 25 push on/push off switches and LED status indicators
Any of the 5 inputs can be patched to any of the 5 outputs simply by pressing the corresponding switches. A patched signal will appear at both normal and inverted outputs simultaneously.

A single input can be patched to a single output. A single input can be patched to multiple outputs. Multiple inputs can be patched to a single output. Multiple inputs can be patched to multiple outputs.

The attenuators allow you to reduce the volume of an incoming signal. If you add many inputs to one output you will of course cause clipping (which may or may not be desirable!), the attenuators are your on-board way around this.

Specifications:

12V draw: 30mA
5V draw: 0mA
-12V draw: 31mA
Depth: 35mm
Width: 18HP

Notes: Shapes is a wide ranging and fully analogue oscillator which can perform duties as both auxilliary VCO* as well as VC-LFO. Shapes can be configured to cycle continuously, or to provide one-shot shaped outputs. When set to one-shot mode, Shapes may be used as an ersatz envelope generator.

Using the Time knob, Shapes can cycle from as low as 8 seconds (whale song) to as high as 19500Hz (bat beeps).

Shapes has 3 simultaneous outputs:

sawtooth (+/-5V, 10Vpp)
ramp (+/-5V, 10Vpp)
triangle (+/-5V, 10Vpp)
Additional waveforms may be derived courtesy of the Shape knob. Anticlockwise from 0 achieves progressively logarithmic sawtooths and ramps, whereas clockwise from 0 achieves progressively exponential sawtooths and ramps. The effect of the Shape knob on the triangle waveform is asymmetric, anticlockwise from 0 achieves progressively logarithmic leading edge, whereas clockwise from 0 achieves progressively exponential falling edge. Progressively exponential triangle waveforms can be achieved using the Time CV knob (set Shape knob to 0) providing there is no jack in the Time CV input socket

Time CV input provides wide ranging control of time. It is possible to dial in something approaching 1V/oct over a limited range, although Shapes has not been designed to perform as an accurately tracking VCO. In the audio range, Shapes comes into its own when used as a 'daughter' VCO to an external 'mother' VCO by patching the 'mother' VCO into Shapes' Gate In input socket - some impressive oscillator sync style effects can be achieved.

Gate In can also be used to initiate waveforms in one-shot mode, where a pulse of any length will cause Shapes to complete one cycle.

*Shapes has not been designed to perform as an accurately tracking audio VCO.

Product Specifications

12V draw: 15mA
5V draw: 0mA
-12V draw: 15mA
Depth: 45mm
Width: 4HP

Notes: Expandable 4 channel VCA based stereo mixer with tone shaping and FX bus.

Chipset:

For this item, Frequency Central offer a CHIPSET which contains the following:

3 x LM13700

For all other components required, please see the build document.

Features:

4 x input channels, each featuring LEVEL, HIGH, LOW, FX send, PAN, MUTE and CV control of level.
FX send and stereo return + FX phase jumper
Left and Right Eurorack level inputs (2 x 3.5mm sockets)
Left and Right line level outputs (2 x 6.35mm sockets)
Scribble strips!

Strips is also expandable! You can add a second strips, connected to the first via a 16 pin to 16 pin cable. The cable powers the second Strips and gives you 8 channels to play with. The second Strips accesses the first Strips FX bus. When using in expanded configuration, the FX send/return and main outputs for the second Strips are not available. Here's how!

FX phase jumper - because not all FX that you might use in the FX loop are in phase with respect to their input/output. The phase jumper allows you to compensate for this and avoid weird phase cancellations.

Product Specifications

12V draw: - 43mA
5V draw: - 0mA
-12V draw: 43mA
Depth: 39mm

Notes: Wonderland is an 8×8 active patchbay/matrix mixer/switcher for both audio and control voltages. It features:

8 inputs (1 through to 8), each with micro-attenuators (which can be set with a small screwdriver)
8 buffered inverted outputs (A through to H) which are 180o out of phase with the inputs
8 buffered normal outputs (A through to H) which are in phase with the inputs
A switch matrix of 64 push on/push off switches
Any of the 8 inputs can be patched to any of the 8 outputs simply by pressing the corresponding switches. A patched signal will appear at both normal and inverted outputs simultaneously.

A single input can be patched to a single output. A single input can be patched to multiple outputs. Multiple inputs can be patched to a single output. Multiple inputs can be patched to multiple outputs.

Each input features a micro-attenuator which can be set with a small screwdriver. This space saving feature allows you to reduce the volume of an incoming signal without having to resort to external attenuators. If you add many inputs to one output you will of course cause clipping (which may or may not be desirable!), the micro-attenuators are your on-board way around this. I find it useful to leave the micro-attenuators set to 50% (which is how they come pre-set at delivery). Of course, their size is a little bit of a compromise, but they are a useful feature nonetheless. Wonderland’s sister module Looking Glass includes full size input attenuators as well as LED status indicators.

Product Specifications
12V draw
30mA

5V draw
0mA

-12V draw
31mA

Depth
35mm

Width
18HP

Notes: Clouds, the granular synthesis module from Mutable Instruments, was discontinued in 2017. Supercell brings back Clouds in a more accessible 34 hp form factor, offering an improved user interface and several additional features:

- Each of the Blend parameters (Feedback, Panning, Mix, and Space) have dedicated knobs with their own CV inputs and inverting attenuators (attenuverters).

- The inputs and outputs now have mute switches, stereo VCAs, and separate VU meters. The knobs act as offset controls when their respective VCA inputs are patched.

- A stereo output gain control has been added, providing an additional +6 dB of gain to compensate for low output levels when using certain parameter combinations.

- The complex process of changing the sampling time and managing presets has been simplified with dedicated switches and status LEDs.

- Extensive modulation options for all parameters including direct patching of external CV, distribution of one CV to all parameters via the AUX input, or an internal smooth random CV that is normalized to any unpatched inputs when AUX is also unpatched. The attenuverters control the modulation depth in all three cases. As of firmware v1.01 the internal modulation rate can be adjusted within a range of 1 to 100 Hz.

- The inputs and outputs now include stereo VCAs and separate VU meters. The knobs act as offset controls when their respective VCA inputs are patched.

- Pitch is now controlled by two separate inputs: the V/Oct input is exponential and the Pitch input is linear. When both inputs are used, their voltages are summed.

- A manual Trig switch (for capturing individual grains) has been added, in addition to the Trig input that was present on Clouds.

All other features of the original Clouds remain intact, including access to the alternate modes. Thanks to Olivier Gillet for making the original Clouds hardware and firmware available under open-source licenses. Third-party firmware such as Parasites (by Matthias Puech) and Beat Repeat (by Julius Kammerl) will be supported in future firmware updates after the initial release of the module.

Notes: A full-on digital modular system in a single module. Eight-voice polyphony, audio processing and CV/MIDI functionality, all customisable via the PC/Mac editor. Serious DSP power in 22 hp.

Supplier's Notes:
Integrate the power of EaganMatrix Sound Technology into your Eurorack! The EaganMatrix Module is a full-featured EaganMatrix Sound Engine for Eurorack, and can be controlled by control voltages and/or Midi. This versatile module can act as a sound source, a sound processor, a CV source (via connection to an external Control Voltage Converter), a Midi source, or a customizable combination of all these capabilities.

The EaganMatrix Module provides a truly versatile framework for both studio and live performance. Flexibility is key, due to its audio inputs and outputs, integrated CV inputs, external CV outputs (via Control Voltage Converter), and robust implementation of MPE and MPE+ Midi.

A single EaganMatrix Preset can give completely different sonic results, depending on how it is patched into a particular Eurorack ecosystem. Hundreds of System Presets are included with the EaganMatrix Module. In addition, an external cross-platform (Mac and PC) Haken Editor may be connected to modify and customize the supplied EaganMatrix System Presets, or create completely new presets from scratch.

The EaganMatrix Sound Technology, originally created for the gesturally highly sensitive Continuum, is now available to you in a Eurorack module. The EaganMatrix Module will quickly become a 'goto' component in your modular sound design and sonic composition.

Haken Audio's EaganMatrix Module offers:
Polyphony: Nominal 1, Maximum 8
Direct CV note control is limited to 1 voice at a time, but higher polyphony avoids voice stealing when EaganMatrix presets have long decays, and higher polyphony is often useful for Midi input.
4 Per-note CV Inputs: W, X, Y, Z
Gate (W) - Triggers at 1V, with max range -10V to +10V
Pitch (X) - 1V per octave, with programmable offset for Middle C; useful input voltages are a subpart of -10V to +10V (depends on the programmable offset selected)
Timbre (Y) - Function depends on EaganMatrix preset; voltage range is normally 0V to 5V, but -5V to +5V can be useful when combined with a programmable offset
Loudness (Z) - normally 0V to 5V, but -5V to +5V can be useful when combined with a programmable offset
4 Global CV Inputs: i, ii, iii, iv

Functionality depends on EaganMatrix preset; these CV affect all voices (notes from WXYZ and Midi); each global CV is normally 0V to 5V, but -5V to +5V can be useful when combined with a programmable offset
2 Analog Audio Inputs: Left and Right, or Mono
2 Analog Audio Outputs: Left and Right, or Mono Sum
-12dB switch selects between Eurorack Level and Line Level
Midi over USB
Allows bidirectional MPE and MPE+ connection to other devices; allows connection to the Haken Editor for editing and archiving EaganMatrix presets (USB-A cable included with purchase)
Universal 3.5mm Midi In (Type A, Type B, and TS)
Allows connection to other Midi devices without need of computer or USB (adapter to 5-pin DIN Midi In included with purchase)
Type B 3.5mm Midi Out
Allows connection to other Midi devices without need of computer or USB (adapter to 5-pin DIN Midi Out included with purchase)
i2c Port for Communication to the Control Voltage Converter
(a switch selects between 3.5mm Midi Out and i2c functionality)
12 Switches, 1 Rotary, and LED Matrix

A menu system allows stand-alone operation without need of computer, and provides monitoring for notes being played and CV input levels
The EaganMatrix is a modular digital synthesizer invented by Edmund Eagan, utilizing a DSP engine designed by Lippold Haken. This is the same EaganMatrix Sound Technology internal to the Continuum Fingerboard, the ContinuuMini, and Expressive E's Osmose keyboard. The EaganMatrix allows the user to finely craft their musical sound by digitally connecting audio and control modules via a patching matrix. The EaganMatrix Module contains a sophisticated digital modular patching world of its own, ready to interact with your other Eurorack modules to make musical results never before possible.

Power and size

The EaganMatrix Module requires +12V, +5V, ground, and -12V from your Eurorack enclosure.

A 16-pin standard Eurorack power cable is included with purchase.

Current requirements: 25mA at +12V and -12V. 300 mA max (190 mA avg) at +5V.

The processing power of the EaganMatrix Module is 2x, same as the ContinuuMini.

The EaganMatrix Module dimensions are 22 HP and 3cm depth.

Notes: 2xSAM is 4 HP Dual Stereo Attenuator-Mixer

Several 2xSAMs can be chained together or with other HN stereo modules via sockets on the back side.

2xSAM's total mix stereo output can be internally sent to the Isolator, PanMix Jr, 3xStereo Mixer, or can be received from OUT, PanMix, PanMix Jr, 3xStereo Mixer, or another 2xSAM.

If jumpers are not installed (placed on one pin only by default) the max gain is 1x. When the jumper is properly placed on both pins - the gain is 5x. There are four inputs thus four jumpers. Each jumper is relevant to its channel.

27 mA +12V
27 mA - 12V
35 mm Depth
4 HP wide

Notes: 3xMIA is a 6-channel attenuverting mixer/offset/scale/polarizer

3 blocks of 2-channel attenuverting mixers, using dual concentric pots. Each channel can be switched to mix with the subsequent channel, allowing for 2-2-2, 4-2, 6 mix configurations.

With nothing plugged into an input, an offset is normalled to that channel. The inner knobs control the A inputs, while the outer knobs control the B inputs.

DC coupled, so it can be used for audio, CV, or both at the same time.

80 mA +12V
80 mA -12V
35 mm Depth
24HP wide

Notes: 3xMIA is a 6-channel attenuverting mixer/offset/scale/polarizer.

3 blocks of 2-channel attenuverting mixers, using dual concentric pots. Each channel can be switched to mix with the subsequent channel, allowing for 2-2-2, 4-2, 6 mix configurations.

With nothing plugged into an input, an offset is normalled to that channel. The inner knobs control the A inputs, while the outer knobs control the B inputs.

DC coupled, so it can be used for audio, CV, or both at the same time.

80 mA +12V
80 mA -12V
35 mm Depth
6 HP wide

Notes: 3xMIA is a 6-channel attenuverting mixer/offset/scale/polarizer

3 blocks of 2-channel attenuverting mixers, using dual concentric pots. Each channel can be switched to mix with the subsequent channel, allowing for 2-2-2, 4-2, 6 mix configurations.

With nothing plugged into an input, an offset is normalled to that channel. The inner knobs control the A inputs, while the outer knobs control the B inputs.

DC coupled, so it can be used for audio, CV, or both at the same time.

80 mA +12V
80 mA -12V
35 mm Depth
6 HP wide

Notes: 3xVCA offers three high class amplifier circuits with linear characteristic. Thanks to AC / DC compatibility, a very low noise floor and basically no distortion, the module is not only a great partner for control voltages, but audio material as well. Besides a signal input and output, each VCA has its own CV input. The dual potentiometers regulate levels and bipolar CV attenuation values of all amplifiers. Using these rather unusual, yet very practical components, it was possible to equip the 3x VCA with a front panel that is only 6 HP wide. Switches allow the user to feed the results of one amplifier to the output of the next amplifier, so we can get 1+2, 2+3, and 1+2+3 outputs mix. Two-colored LEDs visualize CV and output signals.

60 mA +12V
60 mA -12V
35 mm Depth

Notes: Mix up to four stereo channels in just 4hp, or chain multiple modules together to add channels. Inputs are normalled for mono operation. Simple, compact and high quality at a reasonable price.

Supplier's Notes:
4xSt.Mixer is 4 HP quad stereo mixer.

Right inputs are normalled to Left inputs for easy mono operation

Several 4xSt.Mixers can be chained together or with other HN stereo modules via sockets on the back side

65 mA +12V
50 mA -12V
35 mm deep

Notes: 6xMIX is a six channel audio (AC coupled ) mixer, channels arranged in three groups with separate outputs having led indicators. Each group can be switched to mix with the subsequent group, allowing for 2-2-2, 4-2, 6 mix configurations. The module can also be used to mix two stereo channels plus separate group of two mono channels. Perfect audio performance with the lowest noise and distortion amounts.

The inner knobs control the A inputs, while the outer knobs control the B inputs.

Dimensions
6 HP
35 mm deep

Current draw
50 mA +12V
50 mA -12V

Notes: 6xMIX is a six channel audio (AC coupled ) mixer, channels arranged in three groups with separate outputs having led indicators. Each group can be switched to mix with the subsequent group, allowing for 2-2-2, 4-2, 6 mix configurations. The module can also be used to mix two stereo channels plus separate group of two mono channels. Perfect audio performance with the lowest noise and distortion amounts.

The inner knobs control the A inputs, while the outer knobs control the B inputs.

50 mA +12V
50 mA -12V
35 mm Depth
6 HP wide

Notes: Dual xFade is a compact voltage controlled crossfader suitable for both audio and CVs. Smaller knobs set manual crossfade between A<>B, and bigger knobs are CV attenuverters. LEDs show the adjusted positive and negative CV sides for easy monitoring.

Upper inputs (section 1) are normalled to lower inputs (section 2). Thus the same signal pair A&B can be differently crossfaded in both sections.

The switch clones section's 1 controls to the section 2, which is useful to make stereo Dry/Wet adjustment or stereo VCA.

This module can be used as:

two independent crossfades

two independent VCAs

stereo crossfade or Dry/Wet control

stereo VCA

panner

Four jumpers on the back can give optional 5x amplification for each A or B input. Sot it is easy to crossfade modular level with linear level from pedals. Installed jumpers give 1x amplification, removing jumpers gives 5x amplification.

Output 1 is mixed with output 2 if left unconnected.

Notes: Clever FM module that does digital-style through-zero FM using analogue circuits. Use any signals from other modules as your carrier and modulator, then phase modulate or wavefold in the FM Aid.

Supplier's Notes:
FM AID is a module designed to perform through-zero linear Frequency Modulation (FM) in the analog modular world. Any arbitrary signals can be used as a Carrier and Modulator. The module copies FM in how it is done in digital implementation, but in a completely analog circuit free of digital aliasing artifacts. Digital or software FM oscillators are mainly based on a ramp waveform which is then shaped to other waveforms. This is also represented in the FM AID module: sawtooth signal is expected on the Carrier input to give the indicated sine, triangle, sawtooth and square waveforms on the respective outputs. However the user is not limited to only use sawtooth for the Carrier and any other signal can be plugged giving many complex waveforms at the outputs.

All known FM tricks from digital implementation are also applied - you can endlessly experiment with the Carrier/Modulator frequency ratios, Modulation index (FM knob), Modulator's amplitude shaping (CV knob), feedback FM (output is fed back to the Modulator's input) and many other.
Carrier input has normalled connection to the Modulator's input. This internal routing is disconnected each time a plug is inserted in the Modulator's input. That is a handy option which allows the module to be used with only one signal source - this single signal will act as Carrier and Modulator at the same time. There won't be any frequency differences between Carrier and Modulator in this case, but many interesting wave folding sounds will be available anyway.

Technically speaking FM AID uses Phase Modulation, not Frequency Modulation. The sonic difference is that the produces sound is brighter.

SPECIFICATIONS

Carrier input level: -5V ... + 5V (can also accept inputs ranging from -1V ... +1V] to [-12V ...+12V] / [-15V ...+15V] using onboard trimmer)

Modulator input level: preferably -5V ... + 5V

CV input level: preferably -5V ... + 5V

outputs level: -5V ... + 5V

outputs impedance: 1 kOhm

module depth: 3 cm or 1,5 inches

power consumption: +45 /-45 mA at +/-12 Vdc, +50 /-50 mA at +/-15 Vdc

Notes: 1U version of Happy Nerding's effects module, offering a total of 32 effects, with user-storable presets and CV control. Great value in a convenient package.

Supplier's Notes:
32 unique audio effects arranged in 4 banks of 8 effects. Three effect controls plus analogue Dry/Wet control with dedicated CV input. High quality stereo signal pass. Assignable CV input to effect controls or to Sample Rate reducer (changes internal clock). Four user storable presets - stores selected program and all three controls. Spin FV-1 based.

The last used effect, assigns and presets are always remembered.

32 effects are simultaneously available, but FX AID can be reflashed with other effects in any order.

Reflashing procedure is quite easy: playing 40 sec long .wav file of line level amplitude to CV input.

Reflashing mode: hold both buttons for 10 sec.

By default it runs on 32.77 kHz and, if sample rate reduction assign is used, this sample rate can be decreased down to 2000 Hz or brought up to 48 kHz.

Dimensions

24 HP
40 mm deep
Module is a 1U tile in Intellijel format

Current Draw

80 mA +12V
30 mA -12V

Notes: 32 unique audio effects arranged in 4 banks of 8 effects. Three effect controls plus analogue Dry/Wet control with dedicated CV input. High quality stereo signal pass. Assignable CV input to effect controls or to Sample Rate reducer (changes internal clock). Four user storable presets - stores selected program and all three controls. Spin FV-1 based.

The last used effect, assigns and presets are always remembered.

32 effects are simultaneously available, but FX AID can be reflashed with other effects in any order.

Reflashing procedure is quite easy: playing 40 sec long .wav file of line level amplitude to CV input.

Reflashing mode: hold both buttons for 10 sec.

By default it runs on 32.77 kHz and, if sample rate reduction assign is used, this sample rate can be decreased down to 2000 Hz or brought up to 48 kHz.

Dimensions

24 HP
40 mm deep
Module is a 1U tile in Intellijel format

Current Draw

80 mA +12V
30 mA -12V

Notes: 32 unique audio effects arranged in 4 banks of 8 effects. Three effect controls plus analog Dry/Wet control with dedicated CV input. High quality stereo signal pass. Assignable CV input to effect controls or to Sample Rate reducer (changes internal clock). Four user storable presets - stores selected program and all three controls. Spin FV-1 based.

The last used effect, assigns and presets are always remembered.

32 effects are simultaneously available, but FX AID can be reflashed with other user selected Happy Nerding effects in any order. Also the possibility to run freely available third party effects will be added too.

Reflashing procedure is quite easy: playing 40 sec long "wav" file of line level amplitude to CV input.

Reflashing mode: hold both buttons for 10 sec.

Please note the reverse CV operation of the Dry/Wet control: positive CV crossfades from Wet to Dry, and negative CV crossfades from Dry to Wet.

By default it runs on 32.77 kHz and, if sample rate reduction assign is used, this sample rate can be decreased down to 150 Hz or brought up to 48 kHz.

80 mA +12V
30 mA -12V
45 mm deep

Notes: 32 unique audio effects arranged in 4 banks of 8 effects. Three effect controls plus analog Dry/Wet control with dedicated CV input. High quality stereo signal pass. Assignable CV input to effect controls or to Sample Rate reducer (changes internal clock). Four user storable presets - stores selected program and all three controls. Spin FV-1 based.

The last used effect, assigns and presets are always remembered.

32 effects are simultaneously available, but FX AID can be reflashed with other effects in any order.

Reflashing procedure is quite easy: playing 40 sec long "wav" file of line level amplitude to CV input.

Reflashing mode: hold both buttons for 10 sec.

Please note the reverse CV operation of the Dry/Wet control: positive CV crossfades from Wet to Dry, and negative CV crossfades from Dry to Wet.

By default it runs on 32.77 kHz and, if sample rate reduction assign is used, this sample rate can be decreased down to 150 Hz or brought up to 48 kHz.

80 mA +12V
30 mA -12V
45 mm deep

Notes: Upgraded Pro version of the outstanding FX Aid multi-effects module. 200 onboard stereo effects, customisable via an online app, with added CV inputs and even more physical controls. Superb.

Supplier's Notes:
FX AID Pro:

OLED screen shows current effect's number, name and its three parameters

200 onboard effects which can be arranged in any order via the online editor https://fxaid.app/pro

Instant switching of the effects or seek then activate option

Stereo input level control

SRR input can also be routed to parameters 1-3 or effect selection

Advanced internal lfo which can be routed to the Sample Rate, parameters 1-3 or effect selection

Manual control of the Sample Rate with one click for default position

10 user storable presets with handy indicator lines for each stored parameter

Screensaver with 1, 10, 30, 60 minutes options

Easy update by playing wav file, level indicator for proper volumes matching