MIDI converters & accessories

Notes: The audiowerkstatt din2midi2din has a MIDI- and a DIN-sync-output and on both outputs a clock-signal - sent at the same time.

With a button you can select, if the clock-signal present at the DIN-sync- or the MIDI-input is used. A LED indicates the selected input.

The device operates as a standard in "Sync24"-mode (24 clock pulses per quarter note). By holding the button when switching on, the device is started in "Sync48"-mode (48 clock pulses per quarter note).

Notes: Erica Synths MIDI thru box is professional quality, no latency, one MIDI In to 8 MIDI Through splitter in rigid aluminium case. It allows to connect up to 8 instruments to your sequencer or master keyboard and control them simultaneously without undesired delays and interference.

Notes: Receives MIDI clock and stop/start data and converts them to DIN-Sync (Sync-24). Also converts DIN-Sync back to MIDI.

High quality Kenton MIDI MIDI to DIN-Sync converter box with opto-isolated MIDI In plus MIDI Out, Sync In & Sync Out sockets. Powered from a multi-region mains adaptor (wall wart) so you can fit and forget. Can also be powered from a USB socket (although not a USB product)

Notes: Mainly intended as a MIDI volume level indicator where high visibility is needed, the LD2 displays the level both numerically 0 - 127, and on a 20 segment bargraph.

The LD2 isn't restricted to displaying volume only however, it can easily be re-configured to display the data value sent by any controller on any MIDI channel. Factory default is controller #7 (MIDI volume) on MIDI channel #1.

Notes: The LNDR is a master and slave pair that allows MIDI to be sent accurately in both directions at the same time, across distances of over 500m (1640 feet) using a standard Cat5 cable. This is over 33 times the distance achievable using standard MIDI cables. The Master unit is mains powered using the included PSU.

Comes with multi-region power supply

Notes: Merges the data from up to eight separate MIDI sources (e.g. master keyboards, controllers, computers etc.) into a single MIDI data stream which appears at both the MIDI out sockets. Merges all MIDI data including MIDI Clock, MIDI time code and SysEx (see the manual for merging rules). Can also be configured as two completely independent 4 into 1 mergers with the simple press of a recessed button (see manual for details).

- 8 opto-isolated MIDI Ins
- 2 MIDI Outs

Comes with mult-regional power supply

Notes: Your USB device is plugged into the MIDI USB Host mk3 instead of into a computer. It provides MIDI In & Out sockets for USB MIDI keyboards and controllers which have only a USB B type socket. For example, used with a USB-Solo, it allows the USB-Solo to be used in a standard MIDI setup, just like a Pro-Solo. It has a USB Host port (USB A type socket), a MIDI In and a MIDI Out (both 5 pin DIN).

The MIDI USB Host mk3 now has additional features. In addition to the standard operating mode, there are now two further modes.

Standard mode (LED Green):
MIDI data received at the MIDI In socket is sent to the USB device and MID data from the USB device is sent to the MIDI Out socket.

Merge 1 mode (LED Amber):
MIDI IN does not go to USB device but instead is merged with MIDI data coming from the USB device which is then sent to the MIDI Out socket.

Merge 2 mode (LED Red):
MIDI IN data is sent to the USB device & is also merged with MIDI data from the USB device which is then sent to the MIDI Out socket.

The modes are selected sequentially by pressing the recessed push button - the LED colour indicating which mode is current.

The attached USB MIDI device MUST be 'Class Compliant'.

The MIDI USB HOST is powered by a regulated 5V mains adaptor (supplied), and can supply up to 1 Amp of buss power to the attached USB device. This product is supplied with a multi-region power supply suitable for use in most countries.

Attractively finished in brushed aluminium with black screen print

Dimensions: 110mm x 55mm x 32mm

Connecting
You can connect one "Class Compliant" USB device directly into the MIDI USB Host. If your host has the latest firmware already installed then you can plug in a powered USB hub and up to four USB devices can then be connected. Earlier MIDI USB Host mkIIs can be updated with a free download which is available from the support section of our website. Serial numbers N6-2421 already have the hub compatible firmware. Serial numbers N3-0541and upward can be updated.

It is recommended that you attach your USB device to the MIDI USB Host before applying power. Then plug-in and power the power adaptor. The active LED should be lit up. If you apply power with nothing plugged into the MIDI USB Host, the Active LED will flash steadily; this is to indicate that it is waiting for a suitable device to be attached. If it is still flashing when you have attached your device, then it is possible that your device is not class compliant, however you could try turning off the power and start again.

Some USB MIDI devices have two modes of operation and can be set to operate in Class Compliant mode even if this is not the default. The Class Compliant mode might be called "generic driver", the other mode may be called something like "advanced driver". Consult the device manual to see if the mode can be set for Class Compliant.

If you unplug then re-plug the USB cable while it is powered the device might reconnect, but it is not certain.

Power

It is essential to use only the supplied 5V regulated power adaptor. Applying a voltage higher than 5V to the MIDI USB Host will probably not damage the MIDI USB Host itself, but it could damage any attached USB device as the 5V is passed on to the attached USB device for buss power. There is protection circuitry inside the MIDI USB Host to protect against reverse polarity and over-voltage, but these should be treated as a last resort and are not guaranteed to prevent damage to an attached USB device in the event of over-voltage as the USB buss voltage could rise to 6.5V before being clamped.

Care should be taken to ensure that power adaptors for other pieces of equipment are not accidentally plugged into the MIDI USB Host.

If the input voltage rises above 6.5 volts then power will be shut off. The LED will go out and the unit will not operate again until power has been removed for at least 60 seconds. This allows time for the thermal fuse to reset.

The following Yamaha keyboards ar known to be class compliant and therefore should work OK:

PSR-E353, PSR-E443
PSR-S670, PSR-S770, PSR-S970, PSR-A3000, TYROS-5
NP-12, NP-32
DGX-650, DGX-660
P-105, P-115, P-255

The following keyboards are known to incorporate a USB hub and therefore will only work with firmware v2005 or later (s/n N6-2421 and above) for the MIDI USB Host:

Korg Microkey 61
Korg Microkey 49
Korg Microkey 37

Power: 90mA, USB mini-B socket - leaving 910 mA available for the attached USB device
Dimensions: 110 x 55 x 32 mm
Weight: 100g (excluding power supply)
MIDI: 1x IN, 1x OUT - both 5 pin DIN
Power Supply: 5V DC / 1 Amp regulated - (never use an unregulated supply as unregulated supplies typically give a higher output voltage than shown).

This product is supplied with a multi-region power supply which is suitable for use in the UK, EU, US/Canada and AUS/NZ.

Notes: ***B-STOCK: Original box water damaged, product is in different packaging but in perfect working order***


- CV & Gate inputs on 3.5mm mono jack sockets
- A to D conversion for main CV input is 16 bit high quality ADC
- V/octave, Hz/V or 1.2V/oct modes selectable
- Gate type can be selected as Gate or S-trig
- Aux1 & 2 inputs on 3.5mm mono jack (continuously variable or switch selectable)
- Auxes can select controller number
- Auto tune feature makes setup easy
- MIDI Out on 5 pin DIN socket
- Non-volatile memory EEPROM (no back-up battery required)
- 32 bit ARM processor

PLEASE NOTE: Comes with UK 3-pin power supply

Notes: For controlling pre-MIDI drum machines

Designed primarily with the Roland TR-808 / TR-606 and the EDP Wasp / Gnat in mind, the PRO-KADI can, in fact, be used to trigger many drum machines and other devices.

Cheaper than a retrofit and just as effective, it can be used with the TR-808, TR-606, CR78, CR8000, Wasp and many, many more. Most drum machines do need a small modification to run with this interface.

Kenton can supply and/or fit sockets kits to interface your drum machine with the PRO-KADI. Kits are available for the TR-808, TR-606, CR-78 and CR-8000. The Pro-KADI can also be used to trigger the voices of the Simmons SDS-V and SDS-7 however you will need to make your own breakout cable for this.

This multi-mode MIDI trigger unit is highly configurable and capable of driving up to 13 outputs.

Hundreds of other control applications exist, such as lighting control, robotics and ignition of small explosives for theatre productions. Please email us if you have a specificic MIDI control project.

Signal leads are sold separately.

Multi-region power supply included

Notes: For controlling pre-MIDI drum machines

Designed primarily with the Roland TR-808 / TR-606 and the EDP Wasp / Gnat in mind, the PRO-KADI can, in fact, be used to trigger many drum machines and other devices.

Cheaper than a retrofit and just as effective, it can be used with the TR-808, TR-606, CR78, CR8000, Wasp and many, many more. Most drum machines do need a small modification to run with this interface.

Kenton can supply and/or fit sockets kits to interface your drum machine with the PRO-KADI. Kits are available for the TR-808, TR-606, CR-78 and CR-8000. The Pro-KADI can also be used to trigger the voices of the Simmons SDS-V and SDS-7 however you will need to make your own breakout cable for this.

This multi-mode MIDI trigger unit is highly configurable and capable of driving up to 13 outputs.

Hundreds of other control applications exist, such as lighting control, robotics and ignition of small explosives for theatre productions. Please email us if you have a specificic MIDI control project.

Signal leads are sold separately.

Comes with a multi-regional power supply

Notes: Receives MIDI data from a single MIDI OUT (e.g. sequencer or master keyboard) and produces identical copies at the 12 MIDI THRU sockets. These can then be connected to the MIDI IN of sound modules or other devices which require MIDI signals sent to them.

High quality Kenton MIDI Thru box with opto-isolated MIDI In and separate drive for each MIDI Out. Powered from a mains adapter so you can fit and forget.

Notes: * Note that Yamaha has discontinued the BC3A, however we will continue to produce this product in the near term for customers that have previously purchased the BC3A.

The MIDI Solutions Breath Controller is a breath to MIDI converter for use with the Yamaha BC3A Breath Controller (TM). The Breath Controller accepts the BC3A as input and generates continuous MIDI data corresponding to the amount of breath pressure applied to it. The Breath Controller will also accept older Yamaha BC2 units.

The Breath Controller can be programmed to send:

Aftertouch

Pitch Bend

Control Change

System Exclusive

The Breath Controller has a MIDI Echo parameter that is selectable on/off.

Another unique feature of the Breath Controller is its ability to add a variable amount of curvature to the response of the applied pressure of the BC3A. This allows you to correct for a nonlinear response, or to add greater response at one end of the breath range compared to the other.

The Breath Controller is programmed by sending it MIDI System Exclusive messages (see FAQs - Programming). Once programmed, its settings are retained even after power is removed. The Breath Controller can be reprogrammed with new settings as often as needed. The Breath Controller's factory default settings are for it to send CC #7 (volume) on MIDI channel 1, with the Echo parameter set to ON.

The Breath Controller is MIDI-powered, and requires no batteries or power supply to operate with most MIDI products (see FAQs - Power and FAQs - LED for more information). A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it.

weight: 4.1 oz.
dimensions: 4-3/16" x 2-3/16" x 1-3/32"

Notes: The MIDI Solutions Dual Footswitch Controller provides a 1/4" stereo phone jack input for connection to an external dual footswitch or two contact closures which can be used to trigger MIDI events. Triggered MIDI events are merged with incoming MIDI messages and sent to the MIDI output of the Dual Footswitch Controller.

Triggered event types are programmable and include:
Note
Control Change
Pitch Bend
Program Change
Start/Stop
System Exclusive

Other functions include:
Program Change INC/DEC
Rechannelize
Transpose
Tap Tempo
Note-on Filter

MIDI Echo and Footswitch Toggle parameters are selectable on/off.

The Polarity of each footswitch can be determined automatically on power-up, or can be programmed to normally-open or normally-closed. It's also possible for the Dual Footswitch Controller to send out the state of its footswitches immediately on power-up rather than waiting for each to be depressed.

The Dual Footswitch Controller is programmed by sending it MIDI System Exclusive messages (see FAQs - Programming). This is easily done with the MIDI Solutions Programming Tools software. Once programmed, its settings are retained even after power is removed. The Dual Footswitch Controller can be reprogrammed with new settings as often as needed.

The Dual Footswitch Controller is MIDI-powered, and requires no batteries or power supply to operate with most MIDI products (see FAQs - Power and FAQs - LED for more information). A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it.

Notes: If you need to map, filter, and process MIDI events in specific ways, the MIDI Solutions Event Processor may be exactly the solution you are looking for. The Event Processor offers 10 settings, each of which can be programmed with a unique MIDI processing function (for 32 settings see the Event Processor Plus). By combining these settings the Event Processor becomes an extremely powerful tool capable of processing MIDI events in almost any way imaginable. You can map MIDI events or ranges of MIDI events to other MIDI events, filter MIDI events or ranges of MIDI events, trigger MIDI events, toggle between MIDI events, sequence through MIDI events, scale or crossfade MIDI messages, transpose notes, scale velocities, map to and from System Exclusive, NRPN, Bank Select messages, store incoming values in variables for later use... the Event Processor is like a swiss army knife of MIDI processing products, an indispensable tool in any MIDI musician's arsenal.

The Event Processor works by comparing each incoming MIDI event with each of its 10 settings. When an incoming MIDI event matches a setting, the event is processed according to that setting. By combining different settings for different incoming events, the Event Processor becomes an extremely powerful tool capable of achieving a wide range of MIDI-processing functions.

Following is a list of the Event Processor's functions, but better yet download the Event Processor Programming Tools software and read the Guide to the Event Processor and Event Processor Plus by Bruce Wahler of Ashby Solutions. The Programming Tools software is free for download, quick to install, and contains lots of example files that demonstrate the many applications of the Event Processor. And the Guide to the Event Processor and Event Processor Plus is a comprehensive guide that makes it easy to understand everything these amazing products are capable of!

Filter MIDI Events

Map MIDI Events

Trigger MIDI Events

Cycle Through a Sequence of MIDI Events

Turn Settings On and Off

Store Incoming Values in Variables

The Event Processor is programmed by sending it MIDI System Exclusive messages (see FAQs - Programming). This is easily done with the Event Processor Programming Tools software. Once programmed, the Event Processor's settings are retained even after power is removed. The Event Processor can be reprogrammed with new settings as often as needed.

The Event Processor is MIDI-powered, and requires no batteries or power supply to operate with most MIDI products (see FAQs - Power and FAQs - LED for more information). A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it.

weight: 3.8 oz.
dimensions: 4-3/16" x 2-3/16" x 1-3/32"

Notes: The MIDI Solutions Footswitch Controller provides a 1/4" phone jack input for connection to a footswitch or contact closure which can be used to trigger MIDI events (for eight footswitch inputs in a single rack space unit, see the MIDI Solutions F8). Triggered MIDI events are merged with incoming MIDI messages and sent to the MIDI output of the Footswitch Controller.

Triggered event types are programmable and include: Note, Control Change, Pitch Bend, Program Change, Start/Stop, System Exclusive

Other functions include: Program Change INC/DEC, Rechannelize, Transpose, Tap Tempo, Note-on Filter

MIDI Echo and Footswitch Toggle parameters are selectable on/off.

The Polarity of the footswitch can be determined automatically on power-up, or programmed to normally-open or normally-closed.

The Footswitch Controller is programmed by sending it MIDI System Exclusive messages (see FAQs - Programming). This can be done easily with the Processors Programming Tools software. Once programmed, its settings are retained even after power is removed. The Footswitch Controller can be reprogrammed with new settings as often as needed.

The Footswitch Controller is MIDI-powered, and requires no batteries or power supply to operate with most MIDI products (see FAQs - Power and FAQs - LED for more information). A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it.

Notes: ***B-STOCK: Box opened, light surface marks, product in perfect working condition ***


The MIDI Solutions Footswitch Controller provides a 1/4" phone jack input for connection to a footswitch or contact closure which can be used to trigger MIDI events (for eight footswitch inputs in a single rack space unit, see the MIDI Solutions F8). Triggered MIDI events are merged with incoming MIDI messages and sent to the MIDI output of the Footswitch Controller.

Triggered event types are programmable and include: Note, Control Change, Pitch Bend, Program Change, Start/Stop, System Exclusive

Other functions include: Program Change INC/DEC, Rechannelize, Transpose, Tap Tempo, Note-on Filter

MIDI Echo and Footswitch Toggle parameters are selectable on/off.

The Polarity of the footswitch can be determined automatically on power-up, or programmed to normally-open or normally-closed.

The Footswitch Controller is programmed by sending it MIDI System Exclusive messages (see FAQs - Programming). This can be done easily with the Processors Programming Tools software. Once programmed, its settings are retained even after power is removed. The Footswitch Controller can be reprogrammed with new settings as often as needed.

The Footswitch Controller is MIDI-powered, and requires no batteries or power supply to operate with most MIDI products (see FAQs - Power and FAQs - LED for more information). A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it.

Notes: The MIDI Solutions MultiVoltage Quadra Merge merges all MIDI messages appearing at its four MIDI inputs to its two MIDI outputs. All MIDI message types are merged, including System Exclusive, MIDI Clock, and MIDI Time Code messages. A fast merging algorithm ensures that all MIDI data is processed accurately with the minimal possible delay.

The Quadra Merge is MIDI-powered, and requires no batteries or power supply to operate with most MIDI products.

A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it.

MIDI Solutions MultiVoltage products are compatible with both the original 5V and new 3.3V MIDI specifications.

Weight: 128 g (4.5 oz.)
Dimensions: 112 x 62 x 31 mm (4.4" x 2.4" x 1.2")

Notes: The MIDI Solutions Relay contains a relay that can be programmed to open or close in response to MIDI events (for eight relays in a single rack space unit, see the MIDI Solutions R8).

Event types are programmable and include: Note, Control Change, Program Change, System Exclusive

A fast reed relay is used for a response time of less than 2ms. Relay contact is rated at 500 mA. Contacts are made available via connection at the tip and sleeve of a 1/4" mono phone jack. When switching inductive loads be aware of precautions that must be taken to avoid back EMF problems.

The Relay is programmed by sending it MIDI System Exclusive messages (see FAQs - Programming). This can be done easily with the Processors Programming Tools software. Once programmed, its settings are retained even after power is removed. The Relay can be reprogrammed with new settings as often as needed.

The Relay is MIDI-powered, and requires no batteries or power supply to operate with most MIDI products (see FAQs - Power and FAQs - LED for more information). A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it.

Notes: The MIDI Solutions Router is a 1 in 2 out MIDI data router/filter. Selected MIDI messages can be routed to either, both, or neither of the Router's two MIDI outputs.

The Router can route/filter selected ranges of most MIDI data types (see examples). Messages can also be rechannelized to any other MIDI channel. (for on-the-fly rechannelizing, see the MIDI Solutions Footswitch Controller).

The Router will accept a total of 10 settings. Settings are stored in a priority format - if two settings conflict the higher priority setting takes precedence.

The Router is programmed by sending it MIDI System Exclusive messages (see FAQs - Programming). This can be done easily with the Processors Programming Tools software. Once programmed, its settings are retained even after power is removed. The Router can be reprogrammed with new settings as often as needed.

The Router is MIDI-powered, and requires no batteries or power supply to operate with most MIDI products (see FAQs - Power and FAQs - LED for more information). A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it.

weight: 4.0 oz.
dimensions: 4-3/16" x 2-3/16" x 1-3/32"

Notes: The MIDI Solutions Velocity Converter applies selected velocity curves to incoming MIDI notes. Curves can be selected from 40 preset curves or a user defined curve. Even though the 40 presets offer a wide range of curves that are enough to cover most needs, the user curve makes the Velocity Converter a completely versatile device by allowing one curve to be created to an exact specification.

The Velocity Converter can apply a separate curve to each MIDI channel, allowing the velocity response of a sending keyboard to be matched to individual sound modules that are each set to receive on a different MIDI channel.

Another feature of the Velocity Converter is the option to assign velocities based on a selected incoming Control Change value. In this mode, the Velocity Converter monitors the value of a selected Control Change message on a selected MIDI channel, and applies this value to all incoming velocities on that MIDI channel. It is also possible to add an offset to this value to keep the outgoing velocities above a specified level.

The Velocity Converter is programmed by sending it MIDI System Exclusive messages (see FAQs - Programming). This can be done easily with the Processors Programming Tools software. Once programmed, its settings are retained even after power is removed. The Velocity Converter can be reprogrammed with new settings as often as needed.

The Velocity Converter is MIDI-powered, and requires no batteries or power supply to operate with most MIDI products (see FAQs - Power and FAQs - LED for more information). A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it.

weight: 3.8 oz.
dimensions: 4-3/16" x 2-3/16" x 1-3/32"

Notes: ***B-STOCK: Box opened, product in perfect working order***


Compact USB MIDI Interface with 8 x MIDI IN and 8 x MIDI OUT, works Class Compliant without drivers with MAC OSX, Windows XP SP2, Windows Vista, Windows 7, 8 and 10.

The Midiface 8×8 is based on Ploytec's GM5 technology, which means extremely good timing and perfect Sys-Ex stability. When USB3.0 is used for the connection, MIDI flow is further prioritized. This ensures stable and reliable real-time performance for your DAW.