安全なお買い物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全なお買い物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Effects pedals

ホーム  Equipment  

Effects pedals

Options
150/94(ページ1/2)の商品
1  2  »
Subscribe to our weekly Studio Equipment emails
Earth Quaker Devices Bit Commander V2 Analog Octave Synth Pedal
Cat: 781605 Rel: 14 Jul 20
 
Octave synth pedal
Notes: The Bit Commander is a monophonic analog guitar synthesizer with four octaves of vintage square wave synth tones. Its no-nonsense interface makes it easy to add or subtract octaves to create a wide variety of sounds without having to dial in envelopes or oscillators. Ripping sub-octave thump, pulsing octave down, a lightly squared base tone and a swelling transformer based octave up all join together to make a single guitar sound like an army of olde tyme synths.

Controls:
1. Level: Master volume

2. Filter: Tone control more highs clockwise, more warmth counterclockwise

3. Base: Squared input signal level

4. Sub: Two octaves down level

5. Down 1: One octave down level

6. Up 1: One octave up level

This device is true bypass and uses electronic relay-based switching. Audio will not pass without power.

This device takes a standard 9 volt DC power supply with a 2.1mm negative center barrel. We always recommend pedal-specific, transformer-isolated wall-wart power supplies or multiple isolated-output supplies. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!

Dimensions: 4.75 x 2.50 x 2.25 in. (121 x 64 x 57 mm) with knobs
Current Draw: 25 mA
Input Impedance: 50 kO
Output Impedance: <500 O
Read more
MRP:$256.46 SAVE 22%
 1 in stock $199.17
Earth Quaker Devices Cloven Hoof V2 Fuzz Grinder Pedal
Cat: 781610 Rel: 28 Jul 20
 
Fuzz grinder pedal
Notes: The Cloven Hoof is the Hoof's evil twin. It looks a lot like the Hoof, only more, um . . . Cloven.

The tightness and clarity you loved about the Hoof has been kept, along with the wide range of fuzz sounds, and the rest was thrown away. NOS Germanium transistors? Nope! In their place, a set of four specially selected Silicon transistors were installed for cleaner cleans, higher gain, improved temperature stability, and a grittier, grindier, nastier fuzz tone with over 4x the gain of the original Hoof. The key resistors were replaced with with NOS Carbon Comp components to sprinkle a little bit of vintage flavor into the Cloven Hoof's searing fuzz fury. It's like they always say, "In with the old, out with the new".

The Tone and Shift controls remain intact, only now they're re-voiced for a smoother sweep, and more precise control over the Cloven Hoof's beefy low-end. Speaking of low-end, have you heard this thing on bass? Wow. Try the Cloven Hoof on a bass guitar. Seriously- you can still cut or boost the mids, and there's still a metric ton of output on tap, just do us a favor, and for the love of all that's Cloven, play this pedal with a bass guitar.

Controls:
1. Shift: This adjusts the mid content. Clockwise for scooped mids,
counterclockwise for boosted.

2. Tone: Bass to the left. Treble to the right

3. Level: Use this control to make the Cloven Hoof louder or quieter.

4. Fuzz: Clockwise for heavy, counterclockwise for light.

Tech Specs:

This device is true bypass and uses electronic relay-based switching. Audio will not pass without power.

This device can be powered by a 9v battery or a standard 9-volt DC power supply with a 2.1mm negative center barrel. Pedal-specific, transformer-isolated wall-wart power supplies or multiple isolated-output supplies are always recommended. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!

Dimensions: 4.75 x 2.50 x 2.25 in. (121 x 64 x 57 mm) with knobs
Current Draw: 14 mA
Input Impedance: 150 kO
Output Impedance: <10 kO
Read more
MRP:$230.16 SAVE 22%
 1 in stock $179.74
Earth Quaker Devices Erupter	Ultimate Fuzz Tone Pedal
Cat: 781640 Rel: 23 Jul 20
 
Fuzz tone pedal
Notes: When's the last time you turned up your favorite fuzz pedal to anything but eleven? If there's one true thing about rock n' roll, it's that it sounds best cranked all the way up. But where do we go from here? We go one louder. Enter the Erupter.

The Erupter is the result of over two years' worth of tone-chasing, tweaking, and experimentation in search of the ultimate classic fuzz tone with a big low end, a biting top end without being too harsh, and just enough output to politely send a tube amp over the top to deliver a well-rounded and defined fuzz tone with just enough pummeling intensity, so you can rock n' roll all night and still get to bed at a reasonable hour.

It's the perfect fuzz... just sayin'.

Controls:
Bias: This control has a center detent for the perfect fuzz setting. When in the center position, the tone will be big and round with a slight volume boost and great sustain. As you turn this counterclockwise it becomes more gated with lower output. As you turn this clockwise it becomes louder and more refined.

Tech Specs:

This device is true bypass and uses electronic relay-based switching. Audio will not pass without power.

This device can be powered by a 9v battery or a standard 9-volt DC power supply with a 2.1mm negative center barrel. Pedal-specific, transformer-isolated wall-wart power supplies, or multiple isolated-output supplies, are always recommended. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!

Dimensions: 4.75 x 2.50 x 2.25 in. (121 x 64 x 57 mm) with knobs
Current Draw: 9 mA
Input Impedance: 500 kO
Output Impedance: <1 kO
Read more
MRP:$209.12 SAVE 27%
 1 in stock $152.34
Earth Quaker Devices Ghost Echo V3 Vintage Voiced Reverb Pedal
Cat: 781647 Rel: 14 Jul 20
 
Reverb pedal
Notes: You hear that EVP? It's the all new, extra spook-tacular, Ghost Echo calling out from beyond the void! The Ghost Echo is Earth Quaker's spooky take on the haunted amp-top spring reverberation units of yesteryear. This creepy analog/digital spring reverb emulation machine boasts a terrifying 30ms - 150ms of pre-delay, controllable via the Attack knob, for everything from a quick rockabilly slapback to viscous pools of ectoplasmic reverberations. When playing staccato, you'll hear the tortured trails of the reverb, resulting in more of a slapback or echo sound. Legato playing will reveal a massive ambient "depth" that fattens up the sound - and look out, it's right behind you!

Phew, that was close. The Dwell control sets the length and thickness of the decay, which is to say that it controls how long the disembodied spirits of notes no longer with us float through the ether. At the maximum setting it will descend into an infinite loop of self-oscillation. The Depth sets the intensity of the reverb, which you probably know as the wet/dry mix.

Controls:
1. Attack: Adjusts the length of the pre-delay, from 30ms at minimum to about 150ms at maximum. When the Dwell is set to self-oscillate, this will change the pitch of the oscillations.

2. Dwell: Adjusts the length of the decay. This will start to self oscillate around 3 O'clock, the pitch of the oscillations can be changed by turning the Attack control.

3. Depth: Mixes in the wet signal with the dry, unity is around noon and everything after is boosted.

Tech Specs:
This device is true bypass and uses electronic relay-based switching. Audio will not pass without power.

This device takes a standard 9 volt DC power supply with a 2.1mm negative center barrel. Pedal-specific, transformer-isolated wall-wart power supplies, or multiple isolated-output supplies, are always recommended. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!

Dimensions: 4.75 x 2.50 x 2.25 in. (121 x 64 x 57 mm) with knobs
Current Draw: 86 mA
Input Impedance: 10 MO
Output Impedance: 1 kO
Read more
MRP:$230.16 SAVE 17%
 1 in stock $190.70
Click for better price!
or call +44 20 7424 1960
quote 781647
Earth Quaker Devices Grand Orbiter V3 Phase Machine Pedal
Cat: 781668 Rel: 28 Jul 20
 
Phase machine pedal
Notes: Grand Orbiter is a 4 stage OTA-based phaser with a diverse feature set that can go from stationary and resonant to slow and mellow and on through fast and swirly. It has three way toggle switch to select between the ranges of modulation. The master Rate control fine tunes the speed of the LFO in each of these modes and the flashing red LED acts as a visual indicator, even when the effect is in bypass mode. The Depth control blends the shifted signal in with the dry signal and controls the intensity of the effect. The Sweep control governs the peak frequency of the phased signal's tone, turned full clockwise the sweep is lively and intense, whereas turning counter clockwise yields a darker, more laid back peak. The Resonance provides a wide range of control over regeneration and at higher settings adds a more pronounced and resonant tone. You can also use the Grand Orbiter as a true pitch vibrato with the "Phase/Vibrato" switch. When in "Vibrato" mode, the dry signal is removed and the Depth controls acts as a volume control. This pedal is 100% analog, true bypass and built by entirely by hand in beachy Akron, Ohio.

1. Sweep: Controls the frequency peak of the sweep. Higher peak clockwise, lower peak counter clockwise.

2. Rate 1,2,3: Changes the range of the speed control. Rate 1 is slow mode, Rate 2 is LFO kill to use the Orbiter as a fixed resonant filter, Rate 3 is fast mode.

3. Rate: Controls the speed of the LFO. Faster clockwise, slower counterclockwise.

4. Depth: Controls the amount of phase effect mixed with dry signal. Clockwise for more intense phasing, counterclockwise for less. In "Vibrato" mode, this acts as a volume control.

5. Phase/Vibrato: Cuts the dry signal to create a vibe/vibrato effect depending on the setting of the other controls. Vibrato is created by turning the resonance down low.

6. Resonance: Controls the regeneration of the phased signal. More resonant clockwise, more subtle counterclockwise.

Tech Specs:

This device takes a standard 9 volt DC power supply with a 2.1mm negative center barrel. Pedal-specific transformer-isolated wall-wart power supplies, or multiple isolated-output supplies, are always recommended. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!

Dimensions: 4.75 x 2.50 x 2.25 in. (121 x 64 x 57 mm) with knobs
Current Draw: 15 mA
Input Impedance: 1 MO
Output Impedance: <1 kO
Read more
MRP:$261.72 SAVE 25%
 1 in stock $196.19
Earth Quaker Devices Hummingbird V4 Repeat Percussions Tremolo Pedal
Cat: 781684 Rel: 14 Jul 20
 
Tremolo pedal
Notes: The Hummingbird is a choppy, sawtooth tremolo modeled on the vintage "repeat percussion" unit and similar to those found in old Valco and Vox amplifiers. It is capable of producing everything from classic "50's style" shimmering tremolo to a synthy, delay-like chop that turns your signal into a burst of short pings and on through to near ring modulation speeds. Simply choosing between modes 1 (slow), 2 (mid-tempo) or 3 (fast) and adjusting the rate and depth controls will unlock a whole new world of amplitude modulation at your feet. The Rate is also expression pedal accessible to allow instant changes on the fly. Using an expression pedal opens up the possibility of true random amplitude modulation! In addition to the modulation, the Hummingbird has plenty of clean gain on-tap allowing you to either boost or cut the signal using the level control. If the Depth is turned to zero, the Hummingbird will become a JFET clean boost!

Controls:
1. Depth: This adjusts how much the oscillator affects the signal. All the way clockwise produces a full chop, all the way counterclockwise produces no chop and the Hummingbird can be used as a simple JFET booster.

2. Mode: Three way toggle switch which selects the range of the oscillator. Mode 1 is slow, Mode 2 is mid tempo and Mode 3 is fast.

3. Rate: This adjusts the speed of the oscillator. Faster clockwise, slower counterclockwise.

4. Level: Adjusts the output volume

5. Expression Jack: Use an expression pedal to adjust the rate with your foot! When an expression pedal is in use the Rate control is defeated. We recommend the Moog EP-2 expression pedal.

Tech Specs:
Flexi-Switchr Technology
This device features Flexi-Switchr Technology! This relay-based, true bypass switching style allows you to simultaneously use momentary and latching style switching.

For standard latching operation, tap the footswitch once to activate the effect and then tap again to bypass.

For momentary operation, hold the footswitch down for as long as you'd like to use the effect. Once you release the switch the effect will be bypassed.

Since the switching is relay based, it requires power to pass signal.

Power
This device takes a standard 9 volt DC power supply with a 2.1mm negative center barrel. We always recommend pedal-specific, transformer-isolated wall-wart power supplies or multiple isolated-output supplies. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!

Dimensions: 4.75 x 2.50 x 2.25 in. (121 x 64 x 57 mm) with knobs
Current Draw: 10 mA
Input Impedance: 50 kO
Output Impedance: <10 kO
Read more
MRP:$217.01 SAVE 22%
 1 in stock $169.88
Earth Quaker Devices Organizer V2 Polyphonic Organ Emulator Pedal
Cat: 781694 Rel: 14 Jul 20
 
Organ emulator pedal
Notes: The Organizer is a polyphonic organ emulator designed to mimic the organ tones of yesteryear crossed with the highly unique "Guitorgan". It has a warm and very analog feel with a hint of Leslie warble that is unlike other modern octave shifters. It is simple to dial in and tracks chords as well as single notes perfectly all over the neck on both guitar and bass. Not only can the Organizer be used on strings, it has been widely used on everything from vocals and synths to horns and drums. If it makes sound, the Organizer can handle it! The Organizer uses a mix of analog and DSP circuitry with true bypass switching and an all analog dry signal path.

Controls:
1. Up: Level control for the octave up.

2. Down: Level control for the octave down.

3. Choir: This control takes a mix of the octave Up and octave Down setting and regenerates it. The end result is an additional 2 octaves up, 2 octaves down and direct signal with a slight delay that adds a "church organ" like feel. This control only works if the octave Up and octave Down are in use.

4. Lag: Delay control for the wet signal. Full counterclockwise is minimal delay. Delay time increases as it rotates clockwise.

5. Tone: Rolls off the high end as you dial it counterclockwise.

6. Direct: Level control for the analog dry signal.

Tech Specs:
Switching
This device is true bypass and uses electronic relay-based switching. Audio will not pass without power.

Power
This device takes a standard 9 volt DC power supply with a 2.1mm negative center barrel. Pedal-specific, transformer-isolated wall-wart power supplies, or multiple isolated-output supplies, are always recommended. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!

Dimensions: 4.75 x 2.50 x 2.25 in. (121 x 64 x 57 mm) with knobs
Current Draw: 81 mA
Input Impedance: 1 MO
Output Impedance: 500 O
Read more
MRP:$256.46 SAVE 25%
 1 in stock $191.80
Earth Quaker Devices Tone Job V2 EQ & Boost Pedal
Cat: 781748 Rel: 14 Jul 20
 
EQ & boost pedal
Notes: This compact Boost & EQ device is based around the tone-shaping options available in old audiophile-grade stereo preamps, making it a great addition to your pedalboard, no matter what instrument you play.

So what does that mean, exactly? It means that you'll hear full frequency response from your Tone Job everywhere you plug it in - guitar, bass, drum machine, synthesizers, steel drums, harpsichord, kazoo, car stereo, or wherever!

The Tone Job has active EQ controls for Bass, Mid and Treble, with up to 20 dB of cut or boost, which is handy for pairing up with other pedals in your chain to breathe new life into old dirt. Unlike boring old graphic EQs, the Tone Job's EQ controls are interactive, so you can experiment with different settings to alter the response and overall feel of the device, getting your tone out of the lunchroom and back on the clock.

Place the Tone Job at the beginning of your chain to alter the overall character of your guitar, or use it at the end to boost output at the end of a long cable run and fine-tune your tone. The Level control on the Tone Job can boost your signal up to 5x the original input level, so you'll always be heard, and makes for a fantastic solo and/or clean boost!

Controls:
1. Level: Post EQ volume control. Can boost the signal up to 5x the input. Unity is around 10 o'clock.

2. Treble: The center position is flat and marked with a center detent in the potentiometer. All settings above this point boost the treble and all settings below cut treble.

3. Bass: The center position is flat and marked with a center detent in the potentiometer. All settings above this point boost the bass and all settings below cut bass.

4. Middle: The center position is flat and marked with a center detent in the potentiometer. All settings above this point boost the middle and all settings below cut middle.

Tech Specs:
Switching
This device is true bypass and uses electronic relay-based switching. Audio will not pass without power.

Power
This device takes a standard 9-18 volt DC power supply with a 2.1mm negative center barrel. Pedals will make extra noise if there is ripple or unclean power. Pedal-specific, transformer-isolated wall-wart power supplies, or multiple isolated-output supplies, are always recommended. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!

Dimensions: 4.75 x 2.50 x 2.25 in. (121 x 64 x 57 mm) with knobs
Current Draw: 21 mA
Input Impedance: 1 MO
Output Impedance: <1 kO
Read more
MRP:$217.01 SAVE 20%
 1 in stock $174.26
Click for better price!
or call +44 20 7424 1960
quote 781748
EBS Microbass 2 Preamp Pedal
EBS
Cat: 623416 Rel: 23 Aug 16
 
Professional analog signal processing tool with DI box, 2 channel preamp, speaker simulation and effects loop
Notes: The EBS Microbass 2 preamp is the bass players 'Swiss Army Knife'.
A DI box, two-channel preamp, with speaker simulation, effects loop, phones output and loads of other great features. This is the ultimate bass tool. Period!

Two Channels and A Useful Loop. The MicroBass II can be used as an active direct box, a one or two channel preamp, instrument switcher or blender.

The two channels provide sound shaping from high end solid-state types to distorted timbres, using the awarded tube emulation circuitry found in the EBS range of professional bass heads.

An incorporated effects loop gives the user added flexibility for connecting to other effect pedals, or for mixing in an external audio source such as a CD player for rehearsal purposes.

Unmatched Flexibility - The balanced output with speaker simulator option provides unmatched flexibility in live and studio situations. Footswitches control mute and channel operation/switching. Other features include headphone output, low battery indicator, link and master outputs, bass, 'sweepable' midrange, treble, bright and edge filters, drive and effects mix controls.

The EBS MicroBassII delivers that big, burning EBS sound wherever you go.
Read more
 1 in stock $179.74
Click for better price!
or call +44 20 7424 1960
quote 623416
EBS MultiComp Blue Label True Dual Band Compressor Pedal
EBS
Cat: 754903 Rel: 28 Nov 19
 
Analogue, high performance, multi-band compressor pedal
Notes: The EBS MultiComp is the most popular EBS effects unit ever. Thousands of bass players, guitarists, and other musicians all over the world use it on their pedalboards.

The compressor hits the sweet spot between allowing for dynamic playing and creating a smooth consistency across the fretboard. It can also be used simply to push the gain and beef up the overall sound when desired.

You can't go wrong with the MultiComp:

A compressor can be tricky to dial in. Maybe that is why the super intuitive EBS MultiComp has seen such a long-standing success. It is a compressor that you can't go wrong with, that doesn't require a degree in sound engineering and still does exactly what you want. What more to ask for?

A sensible upgrade:

There is a major addition to the new EBS MultiComp Blue Label. A control on the front panel to adjust the threshold level, or Sensitivity. The more you turn up the control, the higher the sensitivity.

The benefit of this is that you can adjust the sensitivity to match the output level of your instrument or your playing style. A centre click indicates the factory setting value on previous editions of the pedal, to offer a reference to your old MultiComp.

More headroom to handle the extremes:

To handle high-end basses equipped with 18V preamps with very hot output, the new MultiComp Blue Label can operate continuously on up to 18V DC power. This gives the pedal enough headroom to handle even these extreme instruments.

The new version has a reduced footprint by 12% and is lighter to save space and weight on your pedalboard. The recessed jacks keep the space needed between pedals to a minimum.
Read more
 1 in stock $162.20
Click for better price!
or call +44 20 7424 1960
quote 754903
EBS MultiComp Blue Label True Dual Band Compressor Pedal (B-STOCK)
EBS
Cat: 768224 Rel: 28 Nov 19
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


The EBS MultiComp is the most popular EBS effects unit ever. Thousands of bass players, guitarists, and other musicians all over the world use it on their pedalboards.

The compressor hits the sweet spot between allowing for dynamic playing and creating a smooth consistency across the fretboard. It can also be used simply to push the gain and beef up the overall sound when desired.

You can't go wrong with the MultiComp:

A compressor can be tricky to dial in. Maybe that is why the super intuitive EBS MultiComp has seen such a long-standing success. It is a compressor that you can't go wrong with, that doesn't require a degree in sound engineering and still does exactly what you want. What more to ask for?

A sensible upgrade:

There is a major addition to the new EBS MultiComp Blue Label. A control on the front panel to adjust the threshold level, or Sensitivity. The more you turn up the control, the higher the sensitivity.

The benefit of this is that you can adjust the sensitivity to match the output level of your instrument or your playing style. A centre click indicates the factory setting value on previous editions of the pedal, to offer a reference to your old MultiComp.

More headroom to handle the extremes:

To handle high-end basses equipped with 18V preamps with very hot output, the new MultiComp Blue Label can operate continuously on up to 18V DC power. This gives the pedal enough headroom to handle even these extreme instruments.

The new version has a reduced footprint by 12% and is lighter to save space and weight on your pedalboard. The recessed jacks keep the space needed between pedals to a minimum.
Read more
 1 in stock $156.52
EBS OctaBass Blue Label Triple Mode Analogue Octave Divider Pedal
EBS
Cat: 751988 Rel: 24 Oct 19
 
OctaBass pedal - Blue Label edition
Notes: The new EBS Octabass Blue Label pushes the boundaries for what has seen as possible with an analogue octave effect. The quality and character of the octave tone, as well as the precision and speed of the tracking, is outstanding.

The EBS OctaBass was the first effect unit ever made by EBS. It is famous for fast and accurate tracking and a fat, natural sound. When you play your instrument, it "tracks" the note you play and produce a sound one octave below to mix in with the note you play. The 'Blue Label' model has a couple of new features that enhance the tracking range and improves the control of the sound.

Improve the tracking where it matters the most:

A new Range-switch makes possible to move the optimized focus area of the tracking to either higher up or lower down the fretboard. All to match your playing style and needs. This feature makes the tracking speed and range outstanding for an analogue octave pedal. Note: Don't confuse this switch with the Range-switch on previous OctaBass pedals where it changed the character of the tone.

Enhanced tone control:

By adding a seamless tone control you can go from a present, focused octave sound that cuts through the mix all the way to a sub-bass backdrop of lows that discreetly supports the note you play. The tone control enhances the palette of sounds and also makes it easier to achieve a synthesized bass sound.

Power the Blue Label OctaBass with 9-18V DC power. The footprint is reduced by 12% compared to the previous Studio and Black Label editions.
Read more
 1 in stock $192.89
Click for better price!
or call +44 20 7424 1960
quote 751988
Electro Harmonix Oceans 11 Reverb Pedal
Cat: 691705 Rel: 25 Jun 18
 
Compact, affordable pedal packed with advanced functionality & eleven reverb styles
Notes: With 11 reverb types and a ton of "hidden" functionality, the Electro-Harmonix Oceans 11 reverb pedal could be your new go-to reverb pedal. You can tap into classic tones like hall, plate, and spring reverbs, including a brand-new spring reverb algorithm that sounds gloriously complex and rich - you can even double-tap the footswitch to "crash" the spring reverb. And you'll be able to cover a huge range of modern tones with a variety of modulated reverbs, shimmer reverb, reverse reverb, and more. A mode switch offers access to variations on many of the 11 reverb types. Complete with an infinite reverb mode for freeze-style effects, there is vast creative potential in the Electro-Harmonix Oceans 11 reverb pedal.

Reverb types:

Hall - rich and full sound of a grand concert hall
Spring - brand-new tube spring reverb emulation
Plate - lush and warm plate reverb
Reverse - each note fades in backwards
Echo - recirculates echoes through the plate reverb algorithm
Trem - hall reverb plus tremolo
Mod - modulated reverb
Dyna - swells, gates, and ducks in response to your playing dynamics
Auto-Inf - auto-infinite reverb, triggers a wash of reverb with each new note or strum
Shim - shimmer reverb with an octave-shifted wash that blooms behind your core tone
Poly - polyphonic reverb with two pitch shifts operating on your pre-reverb guitar tone
Read more
MRP:$185.44 SAVE 17%
 More than 10 in stock $154.54
Click for better price!
or call +44 20 7424 1960
quote 691705
Electro Harmonix Pitch Fork Polyphonic Pitch Shifter Pedal
Cat: 560349 Rel: 04 Feb 15
 
Polyphonic pitch shifter effects pedal, transposes over a +/- three octave range
Notes: The Pitch Fork transposes an instrument's pitch over a +/- three octave range and features three modes which allow the pitch to be transposed up, down or both, simultaneously. The pitch shift amount can be set to a fixed interval or continuously varied by an expression pedal or control voltage.

The controls are straightforward and intuitive. An 11-position Shift switch selects the maximum transposition interval ranging from D (Detune), a shift of 17 cents, through Minor 2nd, Major 2nd, Major 3rd, Perfect 4th, Perfect 5th, Major 6th, Minor 7th, 1 Octave, 2 Octaves and 3 Octaves. A three position toggle switch controls whether the pitch is transposed up, down or both. In Dual mode, two pitch-shifted signals are output. One follows the shift knob as if in the Up position while the other creates a harmony. Dual Mode settings include M3 up + P5 up, P5 up + 1 Oct down, 1 Oct up + 1 Oct down and many others. A Blend knob controls the mix of the dry signal and the effected signal, and an EXP jack enables the player to control pitch and glissando with an expression pedal.

The Latch button selects Latch or Momentary mode which affects how the footswitch and EXP input behave. In Latch mode, the footswitch toggles between effect on and buffered bypass each time it's pressed and the EXP input continuously varies pitch. In Momentary mode the effect is only on while the footswitch is depressed and when it is released the Pitch Fork goes into bypass.

In Latch mode the EXP input controls pitch shift amount, ranging from unity to the interval set by the Shift knob, and pitch varies continuously throughout the expression pedal's range. In Momentary mode the EXP input controls glissando rate for the Pitch Fork's footswitch. When the bypass footswitch is pressed, the Pitch Fork jumps from bypass to the interval set by the Shift knob. The amount of time it takes to reach that new note is the glissando rate. When the footswitch is released the pitch will return to unity at the same rate. That glissando time can vary between 4 milliseconds to two seconds depending on the heel/toe position of the expression pedal. The default glissando rate is 60 milliseconds when nothing is plugged into the EXP input.

The Pitch Fork comes equipped with an EHX 9.6DC-200mA power supply and also runs on a 9Volt battery.

*UK 230V power adapter included*
Read more
MRP:$214.38 SAVE 17%
 7 in stock $178.64
Click for better price!
or call +44 20 7424 1960
quote 560349
FORTHCOMING
Empress Effects Buffer Plus Pedal
Cat: 782953 Rel: 30 Sep 20
 
I/O interface
Notes: The Empress buffer+ was designed to be the complete I/O interface for the pedal board, while maintaining the highest fidelity to your guitar's signal.

Signal loss due to long, un-buffered cable runs is an issue that has plagued guitar players for decades. The primary goal of the buffer+ is to eliminate this signal loss, ensuring that your tone is unchanged by your cables.

Additionally, all the connectivity of your pedal board is consolidated to make set up quick and easy. The buffer+ also has a very handy set of features that make life just a little better. Noise filters, input pads, switchable clean boost and input loading are all powerful tools available on the buffer+.

Input Impedance: 10k - 1Meg
Output Impedance: 510 Ohms
Frequency Response (-3dB): 5Hz - 40kHz
Power Input Voltage: 9V DC (Negative tip)
Power Input Connector: 2.1mm barrel connector (Negative tip)
Power Consumption: 86mA
Total Harmonic Distortion: 0.02%
Signal to Noise Ratio: 105.3dB
Headroom: +9.4dBu
Enclosure Material: Die Cast Aluminum
Input connectors: 1/4" Jack
Output connectors: 1/4" Jack
Height (enclosure): 1.25"
Height with controls: 2"
Length: 4.5"
Width: 2.5"
Weight: 0.5 lbs
Read more
MRP:$210.43 SAVE 17%
coming soon $175.36
FORTHCOMING
Empress Effects Distortion Pedal
Cat: 782987 Rel: 30 Sep 20
 
Distortion pedal
Notes: From mild to crunch to lead, the empress distortion does it all. This true bypass pedal offers three flavors of distortion while retaining a super tight low end and naturally compressing like a high gain amp.

The mild setting offers gentle break-up that cleans up with your volume knob. The crunch setting is tight, with good bite. The lead setting offers high gain with lots of sustain.

Gain control, two bands of EQ and output control allow you to tweak the sound to taste.

Input Impedance: 300k
Output Impedance: 5k
Frequency Response (-3dB): 20Hz - 12kHz
Power Input Voltage: 9V DC (Negative tip)
Power Input Connector: 2.1mm barrel connector (Negative tip)
Power Consumption: ~ 35mA
Enclosure Material: Die Cast Aluminum
Input connector: 1/4" Jack
Output connector: 1/4" Jack
Height (Enclosure only): 1.5"
Height (including controls): 2"
Length: 4.5"
Width: 2.5"
Weight: 0.5 lbs
Read more
MRP:$210.43 SAVE 17%
coming soon $175.36
FORTHCOMING
Empress Effects Fuzz Pedal
Cat: 783034 Rel: 30 Sep 20
 
Fuzz pedal
Notes: This classic sounding fuzz offers smooth, rich sustain with great note definition. A tighter low end makes it ideal for full chords as well as sustaining single notes.

The Empress fuzz is true bypass and has gain control, two bands of EQ and output control to fully tailor your sound.

Read more
MRP:$210.43 SAVE 17%
coming soon $175.36
FORTHCOMING
Empress Effects Germ Drive Overdrive Pedal
Cat: 783038 Rel: 30 Sep 20
 
Overdrive pedal
Notes: True to the tweed tube amps of the 50's, the germ drive delivers warm, harmonically rich overdrive that cleans up with a twist of your volume knob. Its tube-like break-up sounds extremely natural and will enhance your sound without masking the original tone of your instrument.

This true bypass overdrive offers gain control, two bands of EQ and output control to fully tweak your sound.
Read more
MRP:$210.43 SAVE 17%
coming soon $175.36
FORTHCOMING
Fulltone 69 MkII 60's Classic Fuzz With 2 Matched Germanium Transistors Pedal
MRP:$230.16 SAVE 17%
coming soon $191.80
FORTHCOMING
Fulltone 70 70's Classic Fuzz With Matched BC108C Silicon Transistors Pedal
coming soon $163.31
FORTHCOMING
Fulltone Full-Drive 1	 Overdrive Pedal
Cat: 782522 Rel: 26 Sep 20
MRP:$190.70 SAVE 17%
coming soon $158.92
FORTHCOMING
Fulltone Full-Drive 2 V2 Overdrive With Boost Pedal
Cat: 782837 Rel: 26 Sep 20
 
Overdrive pedal
Notes: Since the 1990s, Fulltone's FullDrive series of pedals have been among the most popular overdrive stompboxes around. Undergoing many refinements and tweaks over years to meet the demands of its fans, the FullDrive 2 V2 is the smallest and most pedalboard-friendly version yet!

Featuring a super-compact enclosure without losing any of the key controls or functionality that users adore, this potent-sounding unit can really add some grit to your amp.

2 Footswitches:
Left ON/OFF footswitch: True-Bypass switching with exclusive Fulltone "Anti-Pop" circuit.
Right "Channel select" footswitch: switches between Overdrive 1 or Overdrive 2, each with individually adjustable Volume and Drive knobs.
100% Built in the USA.
16 gauge cold rolled steel chassis with easy battery access via 2 thumbscrews.
9-18VDC operation, extremely green circuit only pulling 10mA of current.

2 toggle switches to access the many clipping options
LEFT 3-position switch:
Comp-Cut- removes clipping diodes, not a clean boost because it can distort the opamp.
Flat Mids- a late 1990's Fulltone invention that feeds signal back on to the clipping diodes removing the Mid-hump.
Vintage- traditional 90's Full-Drive slightly asymmetrical clipping.
RIGHT 3-position switch
Wide- combines Mosfets & Schottky Diodes for more clarity, less compression, a more D*mble-like sound.
Standard- traditional 90's FD2 slightly asymmetrical.
Half-Clipped- another Fulltone exclusive, only clips the top waveform for extreme clarity, feel, and touch like you've never experienced!

Explanation of DRIVE 2 channel.
Think of it as the "More" Channel....
Engaging the DRIVE 2 footswitch brings in the DRIVE 2 knob, allowing you to add distortion (in addition) to what's selected on the DRIVE 1 knob.
At the same time, the pedal jumps from the (pedal's main, large) VOLUME knob level setting to a higher level selected on the DRIVE 2 VOLUME (mini-knob.)
Practical uses:

1) Use as a volume Booster (same Distortion setting, only louder): Set DRIVE 2 knob to "0" and set DRIVE 2 VOLUME mini-knob to taste

2) Use as a higher Gain lead tone with Volume Boost: set DRIVE 2 knob anywhere above "0" and DRIVE 2 VOLUME mini-knob to taste. Ideally you set DRIVE 1 for your lower-distortion sounds and DRIVE 2 for the higher distortion sound...effectively giving you 2 pedals.
Read more
MRP:$230.16 SAVE 17%
coming soon $191.80
FORTHCOMING
Fulltone Full-Drive 3	 Overdrive With Boost Pedal
Cat: 782842 Rel: 26 Sep 20
 
Overdrive pedal
Notes: Unlike its cousin the FD2, the FD3 uses both a JFET input and a JFET op-amp, giving it the most tube-like sound you can get out of a tubeless pedal. Along with great sound, these JFET's give the FD3 an ultra-high Input impedance which allows the pedal to mate with any type/gain of pickup and react well to changes in your guitar's volume control.

3-way CLIPPING toggle switch:
Set to 90's and you'll get symmetrical clipping with ample midrange.
Set the switch to WIDE ASYM (wide asymmetrical) and more sweet highs and lows come through, along with chimey, Class-A style even harmonic overtones.
set to COMP-CUT mode, pure opamp-overdrive, with no diode clipping assistance. Aggressive, cutting, and capable of a huge volume boost to slam the input of your amp.

Discrete Channels:
Unlike the FD2, the FD3 has completely independent OVERDRIVE and BOOST channels, and the ORDER toggle switch allows placing the BOOST channel before or after the OVERDRIVE channel. The BOOST channel is also an extremely transparent, high-headroom 100% JFET-powered circuit.

Buffered Bypass:
Serial# 2548 and higher FD3 pedals are now Buffered-Bypass instead of True-Bypass, so the FD3 will always drive long cables, be isolated from other effects, and always retain the highs and feel of your amplifier whether the pedal is turned ON or OFF. Do not confuse the hi-quality JFET op-amp buffer in the FD3 with the simple single transistor buffers on other pedals. The FD3's buffer sounds rich and fat, not thin.

DYNAMICS knob:
A Fulltone-exclusive Germanium diode Limiter circuit circuit that alters the feel of the notes being played as well as subdues transient spikes which can overload your amp's input. This feature can make even a stiff amp feel responsive and juicy, and sweeten the treble frequencies.

The Icing on the cake? The housing is about 20% smaller than the traditional FD2.

SPECIFICATIONS:
Input impedance: 1.1 mega-ohms. Output Impedance: 180 ohms.
Dimensions: 5.17"W x 4.26"D x 2.36" H. Weight: 1lb 7oz.
Power Consumption: maximum 13 ma with both channels on
Read more
MRP:$230.16 SAVE 17%
coming soon $191.80
FORTHCOMING
Fulltone Mas Malo Distortion/Fuzz Pedal With 3 NOS BC184C Discrete Transistors
Cat: 782844 Rel: 26 Sep 20
 
Distortion/fuzz pedal
Notes: Featuring 3 x hand-picked New old Stock BC184C discrete transistors, this spicy number is capable of vicious, massive sounding Distortion/Fuzz that will feedback infinitely even at bedroom levels! But here's the clincher, dial back the "H" (heat) knob and "D" (distortion) knobs and you can nail many Jimmy Page studio tones as well as your favorite Floyd sounds. Quite possibly the most versatile distortion/fuzz ever made.

In a tiny package (this pedal fits in the palm of your hand) with top-mounted jacks, High Impedance input (sorry Fuzzface) , ultra Low Impedance output, (sorry fuzzface) with an ability to interface with any guitar, effect or amp. Top it off with a beautiful Midrange (sorry fuzzface) and that makes it truly "More Bad"!
Read more
MRP:$195.96 SAVE 17%
coming soon $163.31
FORTHCOMING
Fulltone OCD Candy Apple Red Limited Red Edition of the Obsessive Compulsive Drive Pedal
Cat: 782854 Rel: 26 Sep 20
 
Obsessive compuldive drive pedal
Notes: Limited Red Edition of the Obsessive Compulsive Drive Pedal.
Read more
MRP:$222.27 SAVE 17%
coming soon $185.22
FORTHCOMING
Fulltone OCD V2 Obsessive Compulsive Drive Pedal
Cat: 782848 Rel: 26 Sep 20
 
Drive pedal
Notes: The OCD has received many slight tweaks since its birth in 2004, often incorrectly identified as version 2, Version 3, Version 4. In reality there has always been only one version- Version 1, with very slight variations in a couple of values after that making them V1.0 through V1.8. On 6/15/2017 we released a new OCD, different enough that it warrants a V2 designation, an explanation, and a trip to your favorite dealer to give it another listen. Not a subtle change when turned on- not a subtle change when turned off (in E.B. mode).

The OCD was the first pedal to use Mosfets as clipping devices. Another first was their configuration as "hard clippers connected to v-ref" instead of to ground, as was the norm. These things contribute greatly as to why the OCD has such touch-sensitivity...why they react so well when the strings are hit hard or soft, and why they sound & feel different than all other pedals out there, 90% of which are just slight tweaks of the Tube Screamer.

NEW FEATURE: output buffer (when pedal is turned on in True-Bypass mode, or always when in Enhanced Bypass mode) which eliminates it from being influenced by effects that came after it. Translation, your sound remains consistent regardless of placement in today's more complex signal-chains, loopers, and pedalboards. This buffer also had a positive effect on the sound, it reduced loading on the pedal's hard-clipping stage, allowing more sustain of both the sound and the overtones.

NEW FEATURE: Class A configured discrete 2N5457 JFET input section, raising the input impedance to 1 mega ohms (previously 330K) and increasing the dynamics- resulting in significantly better interaction with both single coil and humbuckers.

NEW FEATURE Internal switch to choose between Enhanced Bypass & True-Bypass, and with no popping sound in either mode. No other company offers EB invented it.
Read more
MRP:$195.96 SAVE 17%
coming soon $163.31
FORTHCOMING
Fulltone Octafuzz OF 2 Octave Up Fuzz Pedal
Cat: 782858 Rel: 26 Sep 20
 
Fuzz pedal
Notes: Octafuzz OF-2

Octafuzz... the only exact circuit copy of the legendary Tycobrahe Octavia. Cool Octave-Up sounds a la Hendrix "Band of Gypsies" and SRV's many live shows! Housed in a 14ga. steel enclosure with a beautiful ranar-blue gloss powdercoat finish and antique-white logo, this pedal is the reincarnation of the Tycobrahe.

"Edgy, tweaked, and haunted by strange overtones, it's distortion occupies a galaxy far, far away from modern crunchola fuzz."
-- Guitar Player Mag

Almost synth-like with its ring-modulation and "steel-drum" vibe... you will turn heads.



Read more
MRP:$209.12 SAVE 17%
coming soon $174.26
FORTHCOMING
Fulltone Plimsoul Hi-Gain Distortion/Overdrive Pedal
Cat: 782862 Rel: 26 Sep 20
 
Distortion/overdrive pedal
Notes: For many, many years you've basically had 2 choices for your Overdrive/Distortion pedals: You could either get "Soft-clipped" Bluesy, slightly compressed, (Toob Screemer, FD2, etc.) type Overdrive pedals... or you could get "Hard-Clipped" (OCD, Distortion+, Boss DS-1, etc.) type Distortion pedals.

What if there was a pedal that offered both? There is now... the Fulltone PlimSoul with it's Patented and completely unique dual stage clipping circuit which VERY accurately replicates not only the sound, but *the feel *of a tube amp with all of its subtleties and complexities.

PlimSoul has those Softer Bluesey, Compressed capabilities but also has a Second Stage that you can roll in with the turn of a little dial to add that firmer, crunchier, British output tube style Distortion! What's more is you not only hear and feel it... you can SEE the pedal reacting to your every mood via a firey LED that glows brighter and dimmer depending on how distorted it is and how hard you're hitting it.

Touch sensitive? Doesn't get any better.

Clean up with the guitar's volume control? More than any, yes, even more than the OCD.

Speaking of OCD, people ask "What's the comparison?" Easy answer: OCD has an honest flat EQ, won't change your amp's tone. PlimSoul has a gorgeous enhanced Midrange and Lower midrange... excellent to transform a combo into a Marshall-like lead machine, not so necessary if you already have a Marshall-like amp.

Good with Humbuckers as well as Single coils?
Yes.

Does it play nice with other pedals?
Yes, it has an Ideal 500K Input Impedance, ideal super low 10K output impedance.

Can I blend the 2 types of Distortion?
Yes, and you can have ONLY Soft clipped or ONLY Hard Clipped.
Read more
MRP:$209.12 SAVE 17%
coming soon $174.26
FORTHCOMING
Fulltone Secret Freq Dynamic Asymmetrical Clipping Overdrive/Distortion Pedal
Cat: 782869 Rel: 26 Sep 20
 
Overdrive/distortion pedal
Notes: What's this, another touch-sensitive, dynamic, natural sounding overdrive/distortion to confuse the marketplace?

Nope, this is the Fulltone Secret Frequency. Secret Freq. for short. Although it does the gig-friendly clean boost and OD thing as good as any, it goes well past that when asked to, right into Rock territory while retaining a natural sound.

Dynamic asymmetrical clipping gives the Secret Freq. a sweet, musical clean boost, juicy overdrive, and rich, touch responsive high gain sounds. Not like the PlimSoul, nothing like the OCD, and not like any other pedal, but worth the price of admission were you to use it simply as is for your bread and butter OD/Distortion pedal.

But the 'Freq has WAY more tricks in its bag than your average transparent OD/Distortion... it just may knock a handful of OD/Distortions right off your 'board and straight on to Ebay thanks to another innocent looking knob labeled Freq.

What's this "Freq." knob?

Turn it Clockwise and my proprietary circuit adds as much as 20db of active narrow band juicy MIDRANGE right where it does the most good, it's like installing a wah-wah right where the distortion is being generated. But unlike turning on your wah-wah along with a distortion pedal, with the 'Freq. the bass and treble frequencies don't disappear... Very unique, and not to be confused with a simple active or passive midrange control tacked on to the end of the circuit, as is the case with all other pedals you've tried with a Mid control. Adding the 'Freq's midrange imparts WAY more sustain and lets you easily place the guitar in the mix where you want it, irrespective of volume... soundman's not going to bury you anymore.

What's it sound like?

Along with a slew of basic great OD/Distortion pedal sounds, it allows you to replicate a very, very wide range of your favorite guitar & amp sounds. Remember that when the 'Freq. knob is fully-counter-clockwise the Midrange enhancement effect is OUT of the picture and the pedal is a truly versatile and natural sounding pretty transparent OD/Distortion! At low to mid overdrive settings, turning the 'Freq knob up a little gets hammer-of-the-Gods penetrating PUNCH!

At more extreme (clockwise) Freq settings?

Brings a smile to your face an evokes the coolest Jimmy Page, Brian May, Michael Schenker, Robin Trower, Tom Scholz tones that you just couldn't previously get without a bunch of studio EQ, just the right setting on a great wah-wah, or a slew of British amps.
Read more
MRP:$222.27 SAVE 17%
coming soon $185.22
FORTHCOMING
Hungry Robot Clockable LFO Desktop Module
Cat: 780980 Rel: 17 Sep 20
 
LFO module
Notes: The Clockable LFO brings multiple waveforms, CV control, subdivisions, and wave symmetry in a simple, user friendly package. LFO speed can be controlled by the tap tempo pushbutton, clock input, or over-sized Speed knob. There are three waveforms that can be selected by toggle and further modified by the Level and Symmetry knob. The Symmetry knob shifts the wave form from a symmetrical wave to a ramp up or ramp down waveform (or when using square wave, acts a pulse width control). Clock In and Clock Out for syncing with other devices. All knobs on the Clockable LFO can be manipulated with CV. As with all Hungry Robot "Modular Boxes" the Clockable LFO can be powered with a simple 9V DC, Negative Center power supply.

KNOBS
-SPEED: Sets the overall speed of the LFO. Turning this knob will override any tap or clocked tempo. This control is still affected by subdivision.
-LEVEL: Sets the level of the LFO output. Ranges from 0-10V peak-to-peak
-SYMMETRY: Sets the symmetry of the waveform. Shifting from ramp-down to ramp-up on triangle and sin waves. Adjusts pulse width on square.

SWITCHES
-SUBDIVISIONS: Selects subdivisions (x1,x2,#2). Automatically converts LFO speed.
-WAVESHAPE: Selects the waveshape of the LFO output (Sin, Triangle, Square)

PATCH POINTS
-SPD CV: CV input for Speed. Allows for CV control of this parameter.
-SYM CV: CV input for Symmetry. Allows for CV control of this parameter.
-LVL CV: CV input for Level. Allows for CV control of this parameter.
-CLK IN: Will sync to external clock. Will override the speed knob.
-CLK OUT: Outputs a 5V clock signal at 50% duty cycle. Can also be useful as a gate signal for your ADSR
-LFO OUT: Two outputs of final waveform. Both outputs are buffered for minimal signal attenuation. 10V Peak-to-Peak

PUSHBUTTON
-CENTER PUSHBUTTON: On-board tap tempo. Will override the speed knob.

Dimensions: 4.7" x 3.7" x 1.96"
Power: 9V DC - Negative Center - 2.1mm Barrel
Read more
MRP:$185.44 SAVE 17%
coming soon $154.52
FORTHCOMING
Hungry Robot The Lumen State Variable Overdrive Pedal
Cat: 780918 Rel: 17 Sep 20
 
Overdrive pedal
Notes: The Lumen is a State Variable FET-Based Overdrive. It marks a return to the overdrive world for Hungry Robot Pedals.

Under the hood, it contains an active State Variable Filter, a type of filter that is common place in the synth world. State Variable Filters offer more clarity and presence than standard passive tonestacks. A typical passive tonestack works by removing tonal content, a State Variable Filter works by actively amplifying frequencies that are already present in your signal. The filter is actually made up of 3 individual filters (low pass, band pass, high pass) that split the incoming signal into 3 frequency ranges and amplifies those ranges without tone loss.

While designing The Lumen, Hungry Robot challenged themselves to create an overdrive that used no diode clipping. The most common approach for an overdrive is to send an amplified signal into a clipping section where diodes chop up the waveform and distortion is create. I opted for a more natural approach of cascading FET gain stages. The distortion is created by soaking the transistors with gain. To me, this method provides a more organic, tube-like saturation than a clipping section.

And to top it all off, The Lumen also has a clean blend, allowing you to mix back in some of your clean tone. At 12 o'clock, the clean signal is near unity gain. Past 12 o'clock, it amplifies your clean signal.

Knobs:

"Drive"- Sets the gain level on the first FET stage. It is normal for the knob to crackle when turned.

"Clean" - Sets the level of the clean blend. Past 12 o'clock is boost.

"Level" - Sets the volume of the drive signal.

"H.P" - Sets the level of the high pass filter.

"B.P" - Sets the level of the band pass filter.

"L.P" - Sets the level of the low pass filter.

Switching: True-Bypass

Dimensions: 4.7" x 3.7" x 1.96"

Powering: 9V DC - Negative Center - 2.1mm Barrel
Read more
MRP:$217.01 SAVE 17%
coming soon $180.83
IK Multimedia Z Tone Buffer Boost Guitar & Bass Preamp & DI Pedal
Cat: 763094 Rel: 18 Jun 20
 
preamp & DI pedal
Notes: Guitar & bass pedalboards are all about exploring new tones & textures, creating a wide range of sound for your instrument. Z-TONE Buffer Boost takes your live rig to a new level, letting you shape the sound of your instrument with the input circuits from our award-winning
AXE I/O interface.

Change the tone & feel of your guitar or bass, buffer your tone to survive even the biggest pedalboard, kick in the boost and supercharge all your existing gear with a powerful new front-end.

Z-TONE Buffer Boost offers a high-quality instrument preamp with exceptionally low noise and wide frequency response, and multiple circuit topologies to adapt to any type of guitar, pick-up and style.

Guitar pickups can dramatically change their character depending on impedance - many amps offer a load of 1 MOhms, while pedals can run much lower. That's why the tone and responsiveness of your guitar can change when plugging into different gear.

Z-TONE Buffer Boost gives you the same variable impedance control as our groundbreaking
AXE I/O audio interface, from 1 MOhm to 2.2 kOhms. At the maximum impedance, you'll find your sound tighter, sharper and more precise. Increase the load and the sound becomes thicker and more bold.

You can use this control to coax a wider range of sounds from a single guitar, experiment with how the rest of your rig reacts to these changes, or dial in exactly the right vibe regardless of what comes next in your chain.

Long cable runs, low-impedance stomps and complex routing can degrade your guitar's signal, causing muffled, bassy or lifeless tone. To ensure your signal always stays crystal-clear, Z-TONE Buffer Boost offers a transparent output buffer so you always sound your best.

And Z-TONE Buffer Boost offers a true bypass circuit, so it's completely transparent when not in use.

In addition to the "Link" amp & pedal output, Z-TONE Buffer Boost offers a balanced XLR output to connect to mixers & PAs. Skip the amp and perform direct, or mix clean and processed signals to create even more tonal options.

A switchable ground lift eliminates noise and hum caused by ground loops, and an unbalanced 14" output offers additional flexibility. Now you're ready to connect in any situation.

And Z-TONE Buffer Boost runs on a standard 9V battery, +48v phantom power from your mixer or 9V pedal power supply, so it's easy to drop onto your existing pedalboard.

Want to add killer Z-TONE tone shaping to all your gear? Check out Z-TONE DI offering the same killer features in a convenient direct box for studio and stage use.

Or check out AXE I/O and AXE I/O SOLO, IK's range of premium audio interfaces offering the same great tone-shaping features, and find out just how easy creating best-in-class guitar recordings can be.
Read more
 1 in stock $165.49
FORTHCOMING
J Rockett Boing Single-Knob Classic Deluxe Reverb Inspired Reverb Pedal
MRP:$222.27 SAVE 17%
coming soon $185.22
FORTHCOMING
Keeley Abbey Verb Vintage Chamber Reverb Pedal
Cat: 782285 Rel: 25 Sep 20
 
Reverb pedal
Notes: Keeley Abbey Verb Vintage Chamber Reverb Pedal
Read more
MRP:$195.96 SAVE 17%
coming soon $163.31
Keeley Aurora Digital Reverb Lush Spatial Studio Quality Reverb Pedal
Cat: 782299 Rel: 04 Aug 20
 
Reverb pedal
Notes: Turn down the lights, turn up the spectrum.

Join Keeley Electronics' grand entrance into the hallowed halls of psycho-acoustic processing - the Aurora Reverb. Few effects complement a guitar better than reverb; from spring reverb coils in a tank to the distant echo of cathedrals to 600 pound sheet-metal plate vibrations. Reverb captures our imaginations and plunges us deeply into our musical psyches. Reverb IS the key to the highway.

At Keeley Electronics, the Aurora Reverb had to meet certain specific criteria. It had to be affordable with no compromise to audio quality. It had to be easy for guitarists to use and be inspiring. And it had to offer the essentials for tailoring your tone without a dozen knobs to learn. Now achieved, we are proud to offer a true bypass, 100% dry analog path, low noise, 24 bit, high-fidelity reverb processor.

AND IT SOUNDS GREAT!

The following controls offer everything from pristine, fast reflections to ethereal spaces to deep, dark and endless caverns.

The Toggle Switch
The three most popular reverb styles that don't come built into your amplifier are Room, Plate and Hall. In the smallest footprint possible, we offer what used to take up a recording studio room or an entire city block. You can achieve cathedral resonance, enormous surface areas of sheet-metal plate sounds or convincing room decays. Room sizes range from something like a broom closet to that of a barn. (Also, careful adjustments to the Room settings yield a signal bordering on the verge of spring reverb, so if your amp doesn't already have a tank, the Aurora pedal has you covered.)

Decay
Decay controls the amount of time it takes for the reverberated sound to disappear. The Aurora pedal provides a range from a realistic, close-quarters reverberated dimension to a "walk-away-and-come- back in a while" signal of complex, still-ringing musical reflections.

Slapback
Otherwise known as "pre-delay". Pre-delay creates distance. How soon or late you hear the first reflection is crucial to crafting the reverberated space. Sometimes you do not want any delay between your note and the reverb. And sometimes, for clarity's sake, you want the reverb to wait a moment before joining the dry signal. Such a setting enables short, staccato, single-syllable type expressions to finish articulating before being suffused AND joined by the tail-end of previously reverberated sounds. The Slapback setting adjusts from zero to 100 milliseconds. When the illusion of infinite space is required, set your Slapback to zero and you'll streak vividly away like Dr. David Bowman breaking free of Jupiter's gravitational pull.

Warmth
Dial up the warmth. Unlike most tone controls, ours is a dampening control and increases the warmth, as it is rolled up. Its brightest setting is when completely dialed down.

Blend
Blend will take your 100% analog dry signal and blend in the reverb, from just the slightest mix of wet to much more. It is recommended that you place it at the end of your pedal chain and use the Blend Knob to tailor your sound.

The Keeley Aurora Reverb provides the essentials guitarists are looking for when they need reverb on their pedal boards. Like that ethereal glow to the mighty Earth herself, Aurora creates a natural halo of sound in the atmosphere of your magnificent core tone.
Read more
MRP:$235.42 SAVE 27%
 1 in stock $171.55
Keeley Bassist Limiting Amplifier Pedal (For Bass)
Cat: 782303 Rel: 04 Aug 20
 
Compresssion & limiting pedal
Notes: The Keeley Bassist Compressor provides true high-fidelity compression and limiting. Be heard and felt using performance compression by Keeley Engineering.

The Bassist Compressor is built around the exotic and extremely high fidelity THAT Corp. 4320. Think of it as very affordable studio-grade compressor in stomp box format! It uses high performance Voltage Controlled Amplifiers, on board true-RMS detector, and ultra high performance op-amps to bring you the very best quality. VCA compressors give you precise control. Therefore they are directly suited to bass guitars. The Keeley Bassist Compressor is both musical and very transparent. Where our older compressors were based on the CA3080 or the LM13700 and are perfect for single coil guitars, the new Keeley Bassist Compressor has no problems with active pre-amps and line level input signals! Not only can the Keeley Bassist handle astonishingly large signals, it has an incredible bandwidth of over 20 KHz and incredibly low noise. No detail in your bass guitar's tone will be lost. The Keeley Bassist will be a sound investment in your tone, you now have rack-mount quality at your feet.

Compression and Threshold

When bass players use the Keeley Bassist Compressor they will be greeted with a sound that is more easily amplified and heard. Using the effect as a limiting amplifier saves your speakers from clipping and distortion. Set the Threshold to look for peaks in your signal and limit distortion from your amplifier or damage to your speakers. Simply watch the Threshold Indicator light to see what type of playing you want to limit, it's that easy! Next set the Compression Ratio Control to determine how much squash you want when the signal is above Threshold. Set Compression all of the way down for no (1:1) compression and use the Gain control as a boost! Set Compression all of the way up for an above-Threshold hard-knee limiter.

A typical soft compressor setting would be 2:1 above threshold. A good starting ratio for the Compression control may be 4:1 as it generally sounds good with bass guitar. A ratio of 5:1 or 6:1 will sound great for slap or funk-style playing. For synth-bass try 10:1 Compression.

Attack and Release

There is a certain figure that just sounds good as far as compression goes; and that's 125 dB/second. With feed forward compressors that use this type of true-RMS detector you use a single time constant parameter. The timing capacitor gives you attack and release times that are adaptive to your playing level or the signal input to the compressor. Bottom line: Attack and Release times vary on program content. Attack times are generally speaking, about 100 times faster than release times.

Attack Time: typically 15ms for 10dB, 5ms for 20dB, 3ms for 30dB

Release Time: typically 8ms for 1dB, 40ms for 5dB, 80ms for 10dB, 160ms for 20dB, 240ms for 30dB

Specs:

Voltage Input: 9V

Current Draw: 50mA

Input Impedance 1 Meg ohm

Output Impedance: 100 ohm

Output Voltage Gain: +30dB Boost

Bandwidth > 20kHz

Total Harmonic Distortion: 0.1%

Noise: -95dBV

Threshold Indicator: Dual LED
Read more
MRP:$261.72 SAVE 25%
 1 in stock $196.19
Keeley Bubble Tron	Dynamic Flanger/Phaser Pedal
Cat: 782324 Rel: 04 Aug 20
 
Flanger/phaser pedal
Notes: The Keeley Bubble Tron Dynamic Flanger.Phaser pedal explores some of the famous, but very hard to find sounds of the past. Keeley Engineering has created another batch of Neo-Vintage effects that never were. This time Keeley has made the Flanger and Phaser in dynamic with your pick attack and strength. Then add the Random Stepped Filter with the new "M-Style Synth" bandpass shaping feature, and you have a lead guitarist's dream tool. Shut up and play your effect pedal! Yeah, you play this thing like an extension of your mind and fingers.

The Keeley Bubble Tron Dynamic Flanger Phaser and Random Synth Filter has three modes of operation.

The Flanger section of the pedal draws on inspiration from the MicMix DynaFlanger. This incredible piece of gear was used by FZ to create many of the sounds in the late 70s to mid 80s where a dynamic flanger was used to get envelope based flanging in his solos. A dynamic flanger is one that starts and stops based on your pick attack or envelope. The word envelope is used because if you were to measure the "weight" of your guitar signal and put it in a storage container (the "envelope" is an imaginary capacitor) it can then be used to control another part of the circuit. The Bubble Tron uses your playing to start and stop the flanger. Most flangers just cycle around and around and you can hear that swooshing in the background. Not in this case, it only cycles as you play. Many flangers offer only positive or negative feedback. This one allows you to try either with the FDBK Control. The negative feedback sounds more vocal like and hollow to my ears while the positive feedback is more conventional and has a thicker, smoother sound. The Sensitivity Control allows you to set how delicately you want to play and have the flanger go fully crazy on you. You can set for crazy silverback gorilla flange or easy flangin' on Sunday morning. The Depth Control is just that, how deep you want the flanging to be.

The DynaMoPhase section of the Bubble Tron is actually two phasers. One has an LFO that you set the speed of with the Rate Control (while it's depth is dynamically controlled) and the other is a true Dynamic Phaser. It starts and stops based on your pick attack. Again, you can set the Depth and and Sensitivity of this phaser to give you a very watery sound that is all based on your guitar's signal. You can turn off the standard phaser and just run it DynaPhase by turning the Rate Control off.

The White Zone is for Loading and Unloading Only.

The only effect that isn't dynamic is the Filter Section of the Bubble Tron Dynamic Flanger Phaser. With the Filter you can control the different ramps or random nature of the pedal with the Shape Control. The very exciting part of this pedal is the Sensitivity Control which is actual like a vintage synth style bandpass filter control. It shapes the bandpass filter on the filter and gives you some incredible keyboard like sounds.

One very nice side effect of dynamic based effects is that they don't produce the constant, swooshing sound of LFO based effects.

If you're a lead guitar player that likes to explore and has never had the kind of expression or dynamics from your sound effects that you have in your mind, this is for you. If you are a sound-experimentalist, this is for you! The sounds are nearly endless in that your input shapes what the effect will do.
Read more
MRP:$261.72 SAVE 27%
 1 in stock $190.70
Keeley Caverns Delay/Reverb V2 Delay Pedal
Cat: 782331 Rel: 04 Aug 20
 
Delay/reverb pedal
Notes: The Caverns Delay Reverb V2 dual-effect pedal combines delay and reverb for the perfect end to any pedal board. It features Keeley's analog-style tape delay with modulation options. The 650ms of warm delay combine with Spring, Shimmer or Modulated Reverb. Caverns now comes with a True-Bypass or Trails option. Because of its small and compact design, the New Caverns is a perfect fit for any fly-rig or small board where you have tight space requirements. The New V2 features Keeley's most popular time-based effects, blended perfectly via a design fine-tuned for over 2 years. Simply put, it will be an amazing addition to any board.

The Reverb side of the pedal features 3 cavernous sounds:

Spring Mode - Blackface Amp style spring reverb with F Style Tremolo
Modulation Mode - Choral modulation to the reverb for a huge, cavernous space
Shimmer Mode - Reverb with emphasis on octave-up voices in the reverb trails

The Delay side of the pedal incorporates Keeley's popular Magnetic Echo circuit, which is designed to emulate analog tape delay lines. Three way switchable modulation gives you options for adding Wow and Flutter to the repeats. Perfectly voiced echoes sit well in the mix, either clean or with distortion.

The New Caverns Delay Reverb V2 builds on the old Caverns pedal by giving players a more open and logical control layout with more space between the foot switches.

Top-Mounted Jacks allow for a compact pedalboard layout.

True-Bypass or Trails option gives you the freedom to create huge caverns of sounds and lets them ring out even after you turn the pedal off. Our buffers are engineered to retain your tone and to feed your amplifier a full-strength signal.

The New Caverns Delay Reverb V2 is entirely built in the US. Keeley's veteran crew builds the most reliable and road-worthy gear.

Use 2 TRS Breakout cables for effects patching or to use the Caverns with a pro switching system.
Read more
MRP:$235.42 SAVE 29%
 2 in stock $167.23
Keeley DDR Custom Drive Pedal With Delay Or Reverb
Cat: 782386 Rel: 04 Aug 20
 
Delay/reverb pedal
Notes: The DDR combines the most common guitar effects- DRIVE and WET- into one pedal. Choose between two classic overdrive tones and then pour on some delay or reverb. One pedal, any gig.

The DRIVE section gives you two styles of overdrive to choose from: Crunch or Lead. The Crunch Style gives you a gritty British tube-amp combo sound. The Lead Style gives you a warm and dark, mid-pushed overdrive. The WET side of the pedal gives you Delays and Reverbs. A Vintage/Modern Switch allows you to toggle between Spring & Plate reverb or Analog & Digital delay. Use the built-in effects loop to insert effects between Drive and Wet, or run it by itself as the only pedal you'll need!

DRIVE Channel:
A pair of modified super-drives to choose from. Volume, Tone, and Drive for days!

STYLE Switch:
Tube-amp Crunch or Lead-channel Sustain

WET Channel:
three knob delay or reverb with Blend, Decay, and Time

Delay/Reverb Switch:
Center toggle, WET Mode Select

Top-mounted jacks for effect pedal insert or split

TRS Insert Switch:
side mounted selector

True-Bypass or Trails Switch:
side mounted selector

9VDC, 100 mA, no battery option
Designed and Made in the USA
Read more
MRP:$235.42 SAVE 26%
 1 in stock $174.26
Keeley El Rey Dorado Overdrive Pedal
Cat: 782412 Rel: 04 Aug 20
 
Overdrive pedal
Notes: The El Rey Dorado is your go-to box for that Plexi tone. Yes, there is a wide range of 1960s Plexi Amp Tone in terms of power, which tubes are installed, which speakers and/or cabinet is used, but the El Rey Dorado hits the core tone bullseye! One of the many reference points for the tone was the JTM 45/100r full stack. (It's a dead-on reissue Marshallr did with crazy cool custom-made vintage-recreation speakers and dual transformers to transfer the load of the 4 EL-84s!)

The El Rey covers a lot of classic British amp tones by featuring two gain modes with the Power Toggle. With the Power Toggle switch you have control over the compression and harmonics. Low Power mode is louder, has more girth, and has fewer harmonics for a more old-school tone. The High Power mode has more compression, more harmonics, and a tighter, more defined tone. Old-school crunch in Low Power mode, super lead tones in the High Power mode.

Simple as grabbing an open E Chord!
Volume, Gain, Tone, Power Toggle: Yes

Keeley Engineered: Yes

Ripe Tide Gain: Yes

9 volt battery: 9V compatible (battery not included)
Read more
MRP:$195.96 SAVE 17%
 1 in stock $163.31
Keeley Filaments High Gain Distortion Pedal
Cat: 782417 Rel: 04 Aug 20
 
Distortion pedal
Notes: Keeley Electronics, the leading manufacturer of pedals built in the U.S., announces the release of their most potent and aggressive metal stompbox to date: the Filaments High Gain Distortion Pedal. The Filaments accurately replicates high-gain tube amps by layering 3 stages of gain while providing 7 ultra-flexible ways to EQ the tone.

The Filaments has more flexibility in tone-shaping than any other Keeley stompbox. Level and Gain set the stage for rich layers of high gain tube-amp saturation. Bass and Body give you the punch and authority of a gain monster no matter what size amp you are playing. Even if you're running a 10-inch speaker the bass and body controls will give you the low end bass response you need. Running through a 4×12 already? Just dial back the body control to keep the sound tight and focused. Have an amp that's hard to push? The Boost and Crunch switches give you two different levels of gain and compression to get your edge just right for your tone. The Presence control works with the Bright control to give any guitar or pickup combination the authority to stand up and shout. Lastly, the Treble control gives you that added range of highs to make your amp sing.

Metal is more nuanced and subdivided that nearly any other style of music outside the classical stuff. The Keeley Filaments High Gain Distortion pedal feels your pain, brother. So of course its amazing 7 layer toneshaping lets you chameleon into any of these types of metal: Christian or Death Metal, Black Metal or Folk Metal, both types of Core, Grind and Metal. Crust Punk or Glam Metal? Progressive Jazz Metal or just good old Stoner Metal? The Filaments pedal has got you covered. Get a Keeley Filaments High Gain Distortion pedal and pound it out !! Get creative! Create your own Metal.

Keeley is well-known for high-end tone and durability. His attention to detail in stompbox tone, tube amp building experience and "tough as nails" build quality ensures his new Filaments pedal will dominate the high-gain pedalboard. Isn't it time you had a high gain pedal that gives you everything you need for the road?

Tech Specs:

9-18 VDC - Louder and More Powerful at 18 Volts!

Ultra Low Current = 10mA

Center Negative Tip

Power Supply Required - No Battery Operation

True-Bypass
Read more
MRP:$248.57 SAVE 21%
 1 in stock $196.19
Keeley Fuzz Bender	 Fuzz Pedal With Active EQ And Gate Controls
Cat: 782420 Rel: 04 Aug 20
 
Fuzz pedal
Notes: The Keeley Fuzz Bender is a 5 knob-3 transistor modern fuzz using a combination of high-gain silicon and silky smooth germanium. What makes fuzz better? Active EQ. Using two gyrators as an active EQ gives you the ability to create massive fuzz tones not possible with typical square-wave boxes. Pummel your amp with over 20dB of boost/cut at 100Hz and 10K Hz. The Fuzz Bender is built around vintage Japanese germanium to create its monumental fuzz tones. With the all new Bias Control, you control the attack and decay of your notes. Anything from Fat Square Waves to Angular Fuzz to glitchy-Velcro attacks are possible with the Bias Control. The Fuzz Bender's five knobs confirm size matters when creating a new and epic world of fuzz.
Read more
MRP:$195.96 SAVE 18%
 1 in stock $160.56
Click for better price!
or call +44 20 7424 1960
quote 782420
Keeley Hooke Reverb Spring/Octave Reverb Pedal With Tremolo
Cat: 782425 Rel: 04 Aug 20
 
Reverb/tremolo pedal
Notes: The new Hooke Spring Reverb from Keeley brings vintage tube-amp spring reverb and tremolo into one package. Bring your Blackface reverb and tremolo on the road with you without lugging around your prized possession! Choose from Classic Spring, Blackface Trem-n-Verb, or an organ-like Fugue-Verb.

The Hooke Spring Reverb begins with a Spring Reverb mode. The main features of this mode include the Tone and Spring controls. The Tone control allows you to work within the range of bright and spanky to dark and thick. The Spring control is the amount "looseness" or "Sproing!" in the reverb pan. Loose springs seem to generate a lot of reflections, and you can hear the reverb "bounce." With the Hooke, you can simulate a specific reverb pan of a vintage amp, two-springs, three-springs, short, medium, long decay ... it's all in there. What's more, combinations of these two controls allow you to fine-tune the tone and the character of the springs and tubes in order to dial in your favorite vintage reverb response. The depth and warmth of the Hooke reverb is simply remarkable. It's one of our finest creations.

Trem-n-verb is designed to give you the ultimate Fullerton, CA black panel Vibrato channel reverb. Everyone knows that it's not really (pitch) vibrato, it's tremolo. Keeley have EQ'd and filtered the sound to not only be tube-like, also crafted a tonal modification that makes for a deep, throbbing tremolo. By adjusting the bias of the output tubes for the volume tremolo, you also dip the volume of the reverb. A special recipe has been created in which the reverb washes over the tremolo texture just a little thickened in order to craft a tone that is truly magical.

The Hooke Reverb needed something crazy, something that just didn't exist. Ah, yes, all wet. All wet is where magic can happen. No original signal, all wet spring reverb with octave up and down. Church Organ, Organ Reverb, Fugue It! Get Hooked and Go Fugue!

Read more
MRP:$235.42 SAVE 22%
 1 in stock $183.04
FORTHCOMING
Keeley Magnetic Echo Delay Vintage "Tape Echo" Style Delay Pedal
Cat: 782430 Rel: 25 Sep 20
 
Delay pedal
Notes: The Mag-Echo pedal simulates tube tape echo sounds by using the delay circuit and a little bit of modulation. Tape echos have long been regarded as a warm and very guitar friendly form of delay. The Mag-Echo achieves similar results by using a touch of Lo-Fi delay, a slightly filtered echo response to keep things warm, and some modulation. Modulation, or "Wow and Flutter" in the tape world is a slight pitch shift or wavering that occurs as the tape is pulled across the heads. The modulation used is similar to what is uses in Keeley's Seafoam Chorus, a slight wavering of pitch on the trails of the repeats. With a simple set of controls for the delay Time, Regen, and Level and with the "Wow and Flutter" controls - Depth and Rate you can create some very vintage or rather unique tones.

Delay Time - This Time control roughly sets the length between your repeats between 40ms and 600ms. This range is well suited for classic, vintage delay sounds that are great for slap-back or medium length delay times.

Regen - This control sets the number of repeats. You can set this for a single slap back echo or turn it up for a runaway, self-oscillating or self-regenerating echoes. (Now go back and twist the Time control for some crazy sounds!)

Delay Level - The Level control is your mix, how loud you want to hear the echoes.

WOW AND FLUTTER CONTROLS

Depth - Turn this control to achieve deeper and deeper chorusing and pitch shifting on your echoes. As you raise the control the Depth and Rate LED will start to glow giving you a visual indication as to the amount of modulation you are applying to the repeats.

Rate - This is your Flutter control. It's another way to control how poorly your tape echo is performing! Not that any tape deck was every in this bad of condition, but it sure sounds good to have a little pitch modulation on your echo! Using these controls gives you a nice way to create unique and very musical delays.

Whether you're into Rockabilly slap-back echoes, experimental sounds, or just want a great classic rock sounding echo, the Magnetic Echo will sound great in your rig.

Keeley Electronics started to develop and produce this delay way back in 2005. But as things happened, we worked on other projects, always keeping an eye on the growing delay and echo market. We sure you will be very happy with the tone of this echo/delay/modulation effect.

It's pretty clear from this unbiased shoot-out that the Magnetic Echo wins. The delays sound more like the original and not as filtered and cut off. The modulation is more sophisticated. Price point is the same!
Read more
MRP:$195.96 SAVE 17%
coming soon $163.31
Keeley Memphis Sun Lo-Fi Reverb, Echo & Double-Tracker Pedal
Cat: 782474 Rel: 04 Aug 20
 
Reverb/echo/double tracker pedal
Notes: The new Memphis Sun - Lo-Fi Reverb, Echo and Double-Tracker is Keeley's second studio themed pedal. Like the Keeley 30ms ADT, this pedal gives you a wealth of tones for capturing that classic Rock-and-Roll sound as well as sounds you've not heard before. It's NeoVintage. It's an Echo and Reverb pedal.
Toggle through the different effects presets:

SLAPBACK 600 - Echo for long delays
SUN MODE - Auto Track-Doubling and slapback with short delays
ROOM - Studio simulation reverb

Both of the ECHO 600 and SUN MODE effects have a Room Reverb.

It's a one-knob, rock and roll type of room reverb.

SLAPBACK 600

Rock and Roll is the Devil's music, right? So of course, the delay time is up to 666ms to simulate some unearthly echo machine that never really existed. Filtering in the Slackback mode is done in stages. First, the response is heavily filtered at 1 kHz then compress the thing. Remember the concept: pack a bunch of sound in a small room and it compresses. Next, it's filtered again at 1 kHz ! Sounds like Rock and Roll, right? Aaron Tackett is the Rock and Roll Doctor of DSP at Keeley. Not only is he devilishly good looking, he has a way of making waves look good - adding curves, so to speak. He has added 2nd and 3rd order harmonics to this mix to simulate tape response and equipment distortions. Waves folded back on themselves. You're gonna love his curves.

Time 30-666ms m/ m/
Regen As Jack White says: "Three." Up to three repeats. Or sometimes six....
Reverb Old Rock-and-Roll Room Reverb.

Sun Mode

Let's Do it Twice Mama, It's Alright! Automatic Double Tracking (ADT) was not available in the 1950s, but it's sneaked in here because it makes a wonderful sound. And, if you lengthen the time, it goes right into slapback territory which is at the heart of Country and Rock and Roll guitar sounds. Like our Keeley 30ms, this pedal will do ADT. The Memphis Sun creates a vintage-voiced double-track in mono. Your guitar-playin' "Gemini-Twin" has a very warmed-up tone. Adjusting the Time Control lets you easily create anything from Double Tracking to Slapback with up to 180ms of delay time.

Time Delay Time is 0-180ms. For Automatic Double-Tracking set this control at the second mark or lower, 0-30ms. For slapback echo 30-180ms sounds great. The knob markers notate 0,30,60, 90, 120, 150, and 180ms
Regen Modulation for the ADT. Set to OFF for NO Rate or Depth. Increasing this control increases both the Rate and Depth of "Tape" modulation.
Reverb It's Still Rock-and-Roll Room Reverb to Me

Room

The Room Reverb simulates a small 33' by 18' asbestos-tiled room so filled with music the sounds actually get compressed- with the frequency response of the mics used back then taken into account. The RCA 77 is loosely simulated by a group of filters including a HPF = 300 Hz and LPF = 8 kHz. Many artifacts are incorporated in our room reverb. And second and third order harmonics are added to make sure it sounds just right.

Time is the Pre-Delay amount: 0-150ms of pre-delay. This allows for a slapback sound as the first reflections come into focus.
Regen is the Tone control: this is an active filter +/- 10 dB and is centered around 1.1 kHz.
Reverb is the Depth control for the reverberations.

That's What I Say Rockin' Robbin!
NeoVintage - Low Fidelity. That's right. That's what I say. This doesn't sounds like some merry band of pixie nymphs playing digital fiddles in your ear.
Read more
MRP:$235.42 SAVE 29%
 1 in stock $167.69
Keeley Neutrino V2 Optocoupler Envelope Filter/Auto Wah Pedal
Cat: 782443 Rel: 04 Aug 20
 
Envelope filter/wah pedal
Notes: The Keeley Neutrino V2 is an amazingly toneful and compact form of the classic opto-coupler envelope filter. The Neutrino takes your guitar playing and creates an automatic wah sound based on your pick attack! Envelope filters or auto-wahs as they are often called, sound and react best when they are opto-coupler based. The opto-couplers used in the Neutrino are particularly smooth, giving you an amazing vowel-like tone. The Keeley Neutrino gives you 3 filter ranges, 2 directions, 2 ranges for the frequency center and a Peak control. Keeley has engineered a power supply voltage-doubler so you maintain the highest headroom for your tone. An incredibly tough build means it will last for many decades to come. Whether you're in a jam band or playing funk, the Keeley Neutrino V2 delivers incredible vocal-like tone.
Read more
MRP:$235.42 SAVE 27%
 1 in stock $171.55
Keeley Oxblood Overdrive Pedal
Cat: 782448 Rel: 04 Aug 20
 
Overdrive pedal
Notes: When inspiration hits, you need the voice to proclaim it. When you need that voice, count on the Keeley Oxblood Overdrive to be your beast of burden.

The Keeley Oxblood Overdrive is Keeley's response to everyone cloning the "Mythical Beast" pedal, with the intent of building an original design, a circuit that lets players blend from perfectly clean to amp-crushing roar, and animpossibly huge and focused midrange that makes any guitar- Strat, Paul, Tele- sound incredible.

Clean, distortion, fuzz - it's all there.
With the Oxblood Overdrive you roll off the Drive Control and get a perfectly clean sound; you can dial in any amount of distortion and volume to stomp an amp into pure tonal Nirvana. The Keeley Oxblood Overdrive offers you two ways to clip and saturate your signal with overtones by selecting carefully chosen diodes. These are different than the standard Oxblood. These diodes were chosen to give you bigger, more open amp tones without a lot of compression.

The key to the ultimate overdrive, in our opinion, is the ability to control five different parameters.

Bass response
The Phat Switch cuts bass response to give you that classic Screamer or that mythic, K-like midrange shelving. The bass response, when cut, is saturated with a hint of 2nd order harmonics. Punchy and full yet not overbearing, it cuts like a buffalo.

Clipping
Sometimes there just ain't enough gain in the world. Well, not so with this beast. The Clipping Switch gives you the ability to sing with near infinite sustain or just stand on your amp like a chief.

Tone Control
You need to be able to dial in the highs perfectly or nothing else matters, right? The highs are what make it ear candy or ice picks, giving you the range to do whatever the heck you want to do. And that's a two-heck sentence.

Volume
You have to be able to put the pedal to the metal whenever you darn well chose. Voltage doubling in our circuit gives you just that. Headroom for days. Slay an amp, leave it a bloody mess. No, you won't blow tubes, but you will have them at the right temperature to make them glow with delight.
Drive. What? You want me to describe Drive? Shoot, from "Is it ON?" cleans to searing sustain and saturation. It pushes you. Compels you to play. Non-stop playing....

Midrange
The 6th sign of a wonderful overdrive pedal is what's under the hood. It's masterful creation of sultry mids. The kind of mids singers or cellos are known for. Throaty and powerful. Not just a woman tone, but a manly roar. Not congested and stuffed up. Focused and brilliant.

Trifecta
The Keeley Oxblood Overdrive was designed by Robert Keeley and Craighton Hale with a lot of help and insight from Jack Orman. Jack Orman has been a pioneer in the modern world of effects for 20 years. His thoughts and ideas are incorporated by nearly every boutique builder out there. Here is your chance to hear a brand new creation designed to outperform any of the clones.
Read more
MRP:$261.72 SAVE 25%
 1 in stock $195.08
Keeley Red Dirt Germanium Special NOS Germanium Transistor Equipped Red Dirt Overdrive Pedal
Notes: Keeley's latest mod to the venerable platform has everyone grinning here at the shop. The Red Dirt Germanium is nothing short of a red hot saturation machine. Perfect classic amp tones.

The Red Dirt overdrive began from a quest to find the perfect classic drive sound while also offering new levels of sonic versatility to satisfy a wider range of musical styles. Founder and head engineer Robert Keeley took this idea and combined the great sounds found within his original "Mod Plus" and "Baked" modified pedals and added refinements found exclusively in his custom pedal line. A Keeley designed FET input stage makes this overdrive breakup in a whole new, genuinely "tube like" style that will have your leads singing and your rhythm playing sounding more dynamic and expressive than ever. It all culminates in an overdrive that is superbly dynamic, with crispness and clarity that let players cut through a dense mix, while retaining the plump midrange. By incorporating these tones along with the Keeley standard of U.S.A. hand-built quality using premium components, the Red Dirt overdrive aims to become an indispensable part of any pedal chain.
Read more
MRP:$235.42 SAVE 17%
 1 in stock $196.19
Keeley Super Phat Mod Full Range Transparent Overdrive Pedal
Cat: 782451 Rel: 04 Aug 20
 
Overdrive pedal
Notes: Many say the Phat Mod delivers their favorite tone from a pedal. It's that natural break-up that just feels good and lets you express yourself. The dynamics make it feel alive and part of your fingers. That's the reason the modified pedal has stayed on people's boards for nearly 15 years. The Keeley Super Phat Mod is the famous mod now perfected with amazing sounding JFETs that emulate old tube amps in a unique way.

The original pedal was a great design that features tube-like amp stages, tube amp tone stacks, and a variety of tone shaping circuits to bring out the best in any guitar's pickups. The problem with building one in the past has been the difficulty finding the perfect FET to capture the magic. If the harmonic content and grain of the distortion and overdrive weren't exactly right, it was put to one side- then Keeley found the magic device that pushed it over the top, and it was dressed in gold and royal purple. The name badge had to speak of its history and heritage. With Super Phat Mod in an old, Blackface-style logo and the metal-flake clear-sparkle on gold, it will look incredible in any rig.

The Super Phat Mod pedal now has incredible dynamics. It is full range and very responsive. The phrase "transparent overdrive" was born of this design! From country pickin', to blues and rock wailing, the Phat Mod is the choice for those not wanting the over-refined sound of a common Screamer. Set the gain high and let your guitar's volume control or your pick attack do the work. With the Super Phat Mod, you now have all of the refinements-the very best of tone-shaping electronics and modern features like true-bypass.

The Keeley BD-2 was the first mod that had a switch. It was done to give players two modes of bass response. With the slight boost, it was called the Phat mode. It was perfect for players of Strats and Teles who wanted just a small push without being muddy. That same design is also available via the micro toggle on the Super Phat Mod. Later on Keeley released the Luna Overdrive which won a Gear of the Year award in England, and that pedal had further refinements made to it and became the Katana Blue Drive. The Katana Blues Drive still retained the active bass and treble controls but smoothed out the highs and increased the gain range slightly. That was an original design designed to meet many of the tonal characteristics of the Blues Driver. The new Super Phat Mod takes off by duplicating the Keeley Phat Mod part-for-part with the exception of the new super JFETs.
Read more
MRP:$195.96 SAVE 22%
 1 in stock $152.34
Keeley Synth-1 Reverse Attack Fuzz Wave Generator Pedal
Cat: 782476 Rel: 04 Aug 20
 
Fuzz wave generator pedal
Notes: The Synth-1 allows you to create fuzzed-out synth waves! Use the Filter and Blend controls to mix your guitar with the fuzz from the synth. Go from churning slow-gear reverse swells to sounding like a light saber.

The Keeley Synth-1 is a guitar-triggered, single-note wave generator. You control the tone of the wave with the Filter Control. The lead-in time or swell of the note is controlled with the Attack knob. Then use the Blend control to remove the natural tone from your guitar as you slide through synth-sounding fuzz waves. Use an expression pedal to control the Filter, and now you have Wah-Wah-like control of the Synth-1.

Synth Wave Generator
Create fuzzed-out, single note synth sounds

Reverse Attack
Volume Swell Effect - put your guitar in slow gear!

Chaos Switch- change dimensional triggering and octaves and stuff

Filter - shape the EQ and tone of your fuzz wave

Wave Selector - change wave modes on the fly with your foot!

Control the Blend of your natural guitar and the wave generator

Side Mount Expression Jack for TRS control of the Filter

Top Mounted Jacks, True-Bypass

Designed and Made in the USA
Read more
MRP:$235.42 SAVE 25%
 1 in stock $176.00
150/94(ページ1/2)の商品
1  2  »

Filter

Effects pedals
DJ機器
Release Date
Featured
Close