安全なお買い物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全なお買い物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Coming Soon: Studio Equipment

ホーム  Coming Soon  

Studio Equipment

Options
150/158(ページ1/4)の商品
1  2  3  4  »
FORTHCOMING
Behringer 150 Ring Mod/Noise/S&H/LFO Module
Cat: 772880
 
150 ring/mod/S&H/LFO module
Notes: This is the Behringer SYSTEM 100 150 RING MOD/NOISE/S&H/LFO. An authentic reproduction of the original System 100M circuitry from the 80's that can fit in a standard Eurorack case- at a very affordable price. Mix the 150 RING MOD/NOISE/S&H/LFO in with your existing rig or start your modular synth journey from here. Either way you're sure to have a lot of fun.

The 150 RING MOD/NOISE/S&H/LFO comes with a ring modulator to create some metallic and bell-like sounds that can be applied to any signal such as a sine wave or a signal from an LFO via the EXT SIG X/NOISE and EXT SIG Y/LFO jacks and out the RING MOD output. The LFO features 5 waveforms including sine, triangle square, ramp and sawtooth. Parameters can be further adjusted by the FREQ and DELAY sliders.

If you want to start layering your song on a droning note or maybe just create some ambience in your music, then you can connect any external signal source into the S&H circuit. A 3-way selector switch allows you to select which type of signal being introduced into the SIG IN jack whether its External Input, LFO or Noise.

Installing the 150 RING MOD/NOISE/S&H/LFO is designed to fit into a standard Eurorack case. Just connect the power cables to the power supply and screw in the module using the included screws. This allows for the 140 to be mixed with other synth modules for a truly unique set up.
Read more
coming soon $84.25
FORTHCOMING
Doepfer A-130-8 Octal Linear VCA Module
Cat: 765896 Rel: 31 Jul 20
 
linear VCA module
Notes: Module A-130-8 contains eight linear voltage controlled amplifiers (VCAs). Each VCA features a control voltage input (CV), a signal input (In) and a signal output (Out). In addition three mixers are included: the socket labelled "1-4" outputs the sum of the VCAs 1-4, the socket labelled "5-8" outputs the sum of the VCAs 5-8, the socket labelled "1-8" outputs the sum of all eight VCAs.

The signal inputs are able to process levels up to 10Vpp without clipping. Each CV input is equipped with a trimming potentiometer that is used to adjust the sensitivity of the CV input in question. In the factory the module is adjusted for the CV range 1...+5V but can be re-adjusted by the user for other control voltage ranges (e.g. 0...+10V).

The amplification range for each single VCA is 0...1. The signals of the sum outputs have a lower amplification to avoid distortion.

The VCAs and mixers are fully DC coupled, i.e. the module can be used for the processing of both audio and control voltage signals. The control voltage and signal inputs can be normalled by means of small solder pads (e.g. 1 > 2 > 3 > 4 and so on, or 1 > 5, 2 > 6, 3 > 7, 4 > 8 for the stereo application mentioned below).

Typical applications:
any kind of VCA application (e.g. voltage controlled attenuation of audio or control voltage signals)
two voltage controlled mixers with four channels each
voltage controlled stereo mixer with four channels each, for this the control voltage inputs have to be correspondingly patched or internally normalled: CV1=CV5 /CV 2=CV6 / CV3=CV7 / CV4=CV8
voltage controlled mixer with eight channels
add-on for the planned Joystick module A-174-4

HP : 6
Read more
MRP:$101.12 SAVE 17%
coming soon $84.25
FORTHCOMING
Behringer 3 Tier Eurorack Module Stand Case
Cat: 780468 Rel: 27 Jul 20
 
module stand case
Notes: Behringer Eurorack Stand 3-Tier; desktop stand for mounting up to 3 Eurorack 104 cases (item 463669), or 3 Behringer synthesizers (e.g. Pro-1, Wasp Deluxe, K-2, Neutron, Model D, Cat).

Variable width (70 HP, 80 HHP or 104 HP); rugged aluminum/steel construction.
Read more
coming soon $65.53
FORTHCOMING
Behringer 173 Quad Gate/Multiples Module
Cat: 772876
 
quad gate & multiples module
Notes: This is the Behringer SYSTEM 100 173 QUAD GATE/MULTIPLES. An authentic reproduction of the original System 100M circuitry from the 80s that can fit in a standard Eurorack case. The best part? It's at a very affordable price. Mix the 173 QUAD GATE/MULTIPLES in with your existing rig to expand its capabilities and you're sure to have a lot of fun.

The SYSTEM 100 173 QUAD GATE/MULTIPLES Module features 4 signal gates (switches) with buffered audio inputs and outputs for immediate signal switching. This provides users the option to choose between a control gate operation, non-inverting (active high) input or an inverting (active low) input.

6-channel multiples, each with 4 floating parallel connectors, are available for optimal signal integrity. You can now send out your signal to other modules to help you create more intricate patches and deliver more compelling sounds from one source.

Installing the SYSTEM 100 173 QUAD GATE/MULTIPLES is simple as it was designed to fit into a standard Eurorack case. Just connect the power cables to the power supply and screw in the module using the included screws. This allows for the SYSTEM 100 173 QUAD GATE/MULTIPLES to be mixed with other synth modules for a truly unique set up.
Read more
coming soon $87.39
FORTHCOMING
Doepfer A-133-2 Dual Voltage Controlled VCA/Polarizer/Inverter/Ring Modulator Module
Cat: 765897 Rel: 31 Jul 20
 
VCA/polarizer/inverter/ring modulator module
Notes: A-133-2 is the slim version of the A-133 but has some additional features and improvements available compared to the A-133.

Module A-133-2 can be used for a lot of applications: as a simple VCA, or a voltage controlled polarizer/attuverter, or a voltage controlled inverter up to a DC coupled ring modulator. In principle the module contains two special voltage controlled amplifiers (VCAs) that allow both positive and negative amplification.

The overall amplification is definded by the sum of the voltage generated by the Man control, the external control voltage CV and the position of the CV control which works as an attenuator for the external control voltage. Without external CV the amplification is +1 when the Man control is fully CW. In the center position the amplification is zero and fully CCW it's -1 (i.e. the incoming signal is inverted). By means of the external control voltage CV the manually adjusted amplification can be modulated. CV can be both positive or negative (i.e. bipolar) to obtain positive or negative amplification values controlled by the external CV.

In addition the CV signal can be modulated via the modulation control input Mod by means of another control voltage. The Mod socket is normalled to +5V, i.e. a constant positive voltage is used as modulation CV provided that no plug is inserted into the Mod socket.

The current amplification is displayed by a dual color LED (note: it's not a signal display but indicates the amplification, probably yellow = positive amplification, red = negative amplification)
Application examples:
voltage controlled amplifier (VCA) with pure positive overall amplification (Man + CV)
voltage controlled inverter with pure negative overall amplification (Man + CV)
voltage controlled polarizer/attuverter overall amplification changing between positive and negative (Man + CV)
DC coupled ring modulator with offset feature, the "classical" ring modulator corresponds to Man=0 and symmetrical audio signals for In and CV
additional effects by means of the modulation feature of the CV signal (using the Mod input)
Read more
MRP:$101.12 SAVE 17%
coming soon $84.25
FORTHCOMING
Behringer 903A Random Signal Generator
Cat: 772802
 
signal generator
Notes: Enter the Behringer 903A RANDOM SIGNAL GENERATOR Module, a vintage-sounding noise generator from the '70s. An authentic reproduction of the circuitry from the "Modular 55" series used by the world's most famous pop, rock and jazz musicians. Now, musicians can build their very own, unique, synthesizer that can fit in a standard Eurorack case for a very affordable price. Mix and match specific modules to create your personal, unique synth to complement the music you play or go all out and fill a room, from floor to ceiling, with modules that'll fulfill any synth geek's wildest dream.

Enter the Behringer 903A RANDOM SIGNAL GENERATOR Module, a vintage-sounding noise generator from the '70s. An authentic reproduction of the circuitry from the Modular 55 series used by the world's most famous pop, rock and jazz musicians. Now, musicians can build their very own, unique, synthesizer that can fit in a standard Eurorack case for a very affordable price. Mix and match specific modules to create your personal, unique synth to complement the music you play or go all out and fill a room, from floor to ceiling, with modules that'll fulfill any synth geek's wildest dream.

The 903A RANDOM SIGNAL GENERATOR generates both white and pink noise via two 3.5 mm outputs each allowing you to send different signals to other modules in your rig.

Installing the 903A RANDOM SIGNAL GENERATOR is simple as it was designed to fit into a standard Eurorack case. Just connect the power cables to the power supply and screw in the module using the included screws. This allows for the 903A RANDOM SIGNAL GENERATOR to be mixed with other synth modules for a truly unique set up.

Read more
coming soon $54.09
FORTHCOMING
Behringer 923 Filters Module
Behringer 923 Filters Module (eurorack module)
Cat: 772935
 
filters module
Notes: Enter the Behringer 923 FILTERS. An authentic reproduction of the circuitry from the Modular 35 and 15 series filters used by the world's most famous pop, rock and jazz musicians. Now you can build your very own, unique synthesizer that can fit in a standard Eurorack case for a very affordable price. Mix and match with specific modules to customize your synth and complement the genre of music you play or go all out and have a room filled from floor to ceiling with modules that'll fulfill any synth geek's wildest dreams.

The 923 features separate Low and High Pass filters each with their own dedicated frequency cutoff controls. The Low Pass filter control will roll off all frequencies above the set threshold frequency from 10Hz to 10KHz while the High Pass filter control will roll off frequencies below the set frequency. Each filter comes with their own 3.5 mm ins and outs giving you the ability to route incoming signals through the IN jack, through the filter and back out the OUT jack.

For you to shape an endless number of tones, the 923 comes with a white and pink noise generator. Use the parallel jacks for each of the noise sources to send out a white or pink noise signal and start sweeping frequencies to build tension and excitement in your songs, or use them to create some percussive sounds for a real groovy drum beat.

Installing the 923 is simple as it was designed to fit into a standard Eurorack case. Just connect the power cables to the power supply and screw in the module using the included screws. This allows for the 923 to be mixed with other synth modules for a truly unique set up.
Read more
coming soon $83.23
FORTHCOMING
Behringer 961 Interface Module
Cat: 772932
 
interface module
Notes: Enter the Behringer 961 INTERFACE Module. An authentic reproduction of the circuitry from the Modular 55 Series used by the world's most famous pop, rock and jazz musicians. Now, musicians can build their very own, unique, synthesizer that can fit in a standard Eurorack case for a very affordable price. Mix and match specific modules to create your personal, unique synth to complement the music you play or go all out and fill a room, from floor to ceiling, with modules that'll fulfill any synth geek's wildest dream.

The 961 features an audio to V-Trig Converter, allowing you to plug in any audio source and transform it into a voltage trigger to drive other modules in your rig. Dual S-Trig to V-Trig and a multichannel V-Trig to S-Trig converters on the 961 can be utilized to switch or control a particular function on other modules.

Controls on the 961 include a Sensitivity knob that adjusts the gain of the audio signal coming into the module via the Audio In jack. Column B in each V-Trig In bank has a Switch-On Time knob you can use to manually control how short or long the "ON" duration is for S-Trig signals. This feature is normally used to drive the 911 envelope generator. Add a 960 sequential controller to release the full creative potential of this interface module.

Installing the 961 INTERFACE is simple as it was designed to fit into a standard Eurorack case. Just connect the power cables to the power supply and mount the module using the included screws. This allows for the 961 INTERFACE to be mixed with other synth modules for a truly unique set up.
Read more
coming soon $83.23
FORTHCOMING
ADDAC System ADDAC200PI Pedal Integrator Module (red faceplate)
Cat: 776156
 
pedal integrator module
Notes: This small utility is the pedal's lover best friend, it allows 2 diferent chains of pedals to be independently connected to your synth.

The Send channels attenuate the synth level to instrument level.

The Return channels amplify the signal from instrument to synth level.

Specs:
. Width: 4 HP
. Depth: 3 cm
. Max current: 10mA
Read more
MRP:$96.13
coming soon $93.62
FORTHCOMING
Behringer 995 Attenuators Module
Cat: 772930
 
attenuators module
Notes: Enter the Behringer 995 ATTENUATORS. An authentic reproduction of the circuitry from the Modular 55 and 15 series attenuators used by the world's most famous pop, rock and jazz musicians. Now you can build your very own, unique synthesizer that can fit in a standard Eurorack case for a very affordable price. Mix and match with specific modules to customize your synth and complement the genre of music you play or go all out and have a room filled from floor to ceiling with modules that'll fulfill any synth geek's wildest dreams.

The 995 features three separate attenuators each with their own independent inputs and outputs. The attenuators can be used to adjust the level of the input signal passively from - 8 to unity gain and accept both audio and CV signals. Connecting a single signal to the first input will allow it to pass to all 3 outputs for up to 3 variable outputs of a single signal source. Introducing a signal into the subsequent outputs will break the chain from the previous input. For example, if you have a signal in input 2, then this will feed into input 3 leaving input 1 to feed out of output 1.

Installing the 995 is simple as it was designed to fit into a standard Eurorack case. This allows for the 995 to be mixed with other synth modules for a truly unique set up.
Read more
coming soon $57.21
FORTHCOMING
Behringer Podcastudio 2 USB Bundle with USB Audio Interface
Cat: 772939
 
podcasting bundle
Notes: The PODCASTUDIO 2 USB bundle has everything you need to make high-quality podcasts, produce your own music and home recordings - plus it works seamlessly with your PC or Mac* computer! All the software you'll need is provided- a XENYX 302USB mixer with built in USB/audio interface, XM8500 microphone, HPM1000 headphones and much more - you'll be up and running in mere moments, right out-of-the-box!

No matter what your audio mixing needs, the XENYX 302USB provides the performance and features that can take your talent to the next level. With its professional sound quality, 5 Inputs with the legendary XENYX mic preamp, built-in USB/audio interface, plus rugged reliability - the XENYX 302USB is ideal for both your live gigs and recording sessions.

The XM8500 dynamic microphone is a performing/home recording enthusiast's dream come true! This professional-quality microphone is designed to capture your sound with outstanding sensitivity and accuracy. With its cardioid pickup pattern for excellent sound source separation and feedback rejection, this ultra-wide frequency response mic is an excellent choice for any performing or recording scenario - and it's rugged enough to go the distance! With its integrated shock mount system, mic stand adapter, spherical wind and pop filter, all in an impact-resistant carrying case - the XM8500 just may be the only microphone you'll ever need.

HPM1000 headphones provide everything you need for comfortable listening. The oval-shaped ear cups contain high-resolution capsules that deliver every nuance of your sound. Featuring a single-sided cord that resists tangling; an ultra-comfortable headband; and a 1/4" adapter for the 1/8" connector, HPM1000 phones are compatible with everything from your smartphone - to your mixing console.

Because you'll want to take full advantage of your XENYX 302USB's recording and podcasting potential, all the software you'll need for audio recording, editing and even podcasting is included - all free of charge and downloadable from behringer.com. You'll be ready to go live on your PC or Mac right out of the box. A free download of more than 150 virtual instruments and FX plug-ins is provided - turning your computer into a powerful home-based or mobile recording studio from input to output.

This amazing PODCASTUDIO 2 USB setup includes a: professional 5-input XENYX 302USB mixer with the studio-grade XENYX Mic Preamp; pair of high-quality HPM1000 headphones; great-sounding XM8500 dynamic mic - and all the cables and recording/podcasting software you'll ever need.
Read more
coming soon $94.67
FORTHCOMING
Division 6 Business Card Sequencer V2
Cat: 777968 Rel: 06 Jul 20
 
business card sequencer
Notes: The Division 6 packs a lot of sequencer into a tiny package! This 16-step circuit can work as a sequencer or as a handheld keyboard.

Specifications:
Power In: 7-15VDC, tip positive through a 3.5mm jack. Find a voltage source on your synth to power it if you can! A 9V battery or AC adapter will work too.

Power supply: 7-15VDC (reverse-polarity protected!)
Power connection: 3.5mm phone jack, center-positive
Current draw: 15ma
Dimensions: 3.5" x 2" (the same as a business card!)
Read more
MRP:$103.62 SAVE 19%
coming soon $84.25
FORTHCOMING
ADDAC System ADDAC213A Eurorack Bridge Module (black faceplate)
Notes: A pair of ADDAC213As acts as a simple one-cable bridge between different cases. By itself the ADDAC213As can send/receive 8 CV or audio signals between your cases, but can be expanded to bridge two cases for up to 24 signals at the same time.

Use a pair of ADDAC213As to send & receive 8 CV or audio signals between distant points in your case, between two separate cases, or between your case and a friend's case. Less clatter, less spaghetti, faster connection! There's nothing better than being able to connect that controller skiff with just one cable to your main system. At a gig, in the studio, when jamming with a friend, give yourself a gift by grabbing a pair of ADDAC213As.The modules can be installed in normal position or a 180 degree position to fit any need and any case design.

Each ADDAC213A module can be connected through a ribbon cable connection on its backside with up to two ADDAC213Bs. Each ADDAC213B module added expands the channels options of the ADDAC213A by adding 8 more channels. With two 2 ADDAC213Bs connected to each ADDAC213A module, you'll have a total of 24 channels going between your cases with a simple one-cable bridge. Between the ADDAC213A pair and the ADDAC213B, your cases never looked so elegantly connected together!

The ADDAC213As are always sold as a pair of 2 modules and an included ribbon cable.

Each module can be installed in normal position or at 180 degrees.

Mechanical:
. Format: Eurorack
. Width: 6 HP
. Depth: 2.4 cm

Electrical:
Passive / Does not draw current
Ribbon Cable: 50cm or 100cm ribbon cable
Read more
MRP:$102.37
coming soon $98.82
FORTHCOMING
Happy Nerding 3x Stereo Mixer Module (black faceplate)
Cat: 777909 Rel: 31 Aug 20
 
stereo mixer module
Notes: 3x Stereo Mixer is a high quality 3 channel stereo mixer with manual volume controls. Total mix Left and Right outputs available on separate jacks, plus L&R stereo jack can be used to route the mix via single stereo cable or drive the headphones. Channels 1 and 2 can be muted with the relative switches. Left and Right led indicators available for all three channels.

All left channel inputs normalled to be used as mono inputs.

Several 3x Stereo Mixer modules can be chained together via connections on the back side. This connection is possible with other Happy Nerding stereo modules too. At the moment PanMix Jr and 3x Stereo Mixer can be connected in both ways. Also their stereo outputs can be internally sent to the Isolator module. Or stereo signal can be received from OUT and latest revision of PanMix.

50 mA +12V
50 mA - 12V
35 mm Depth
6 HP wide
Read more
MRP:$116.10 SAVE 17%
coming soon $96.75
FORTHCOMING
Doepfer A-183-4 Quad Level Shifter Module
Cat: 765895 Rel: 31 Jul 20
 
level shifter module
Notes: Module A-183-4 is a fourfold level shifter. A level shifter is required if the level of a digital control signal has to be increased or decreased. A typical application is the conversion of a gate, trigger or clock signal with +5V voltage level (tolerance range +2...+5V) to +12 voltage level. The output voltage level can be set by means of a jumper to +12V or +5V. The factory setting is +12V. But it can be changed to convert also a higher to a lower level (e.g. +12V to +5V). But this application is required rarely. The output level setting by means of the jumper is global, i.e. it is valid for all four units and cannot be set individually for each unit. The four output signals are displayed by means of LEDs.

The outputs and inputs of the four sub-units are normalled via the switching contacts of the input sockets, i.e. the output signal of the upper unit is used as input signal of the unit below provided that no patch cable is inserted into the input socket of the lower unit. That way the module can be used also as clock/trigger/gate buffer or buffered multiple for digital signals. For this the signal that has to be buffered is connected to input 1. The buffered (and possible level shifted) signal appears then at all four outputs.
Voltage thresholds for the input voltages:
voltages below +0,8 V are treated as "low"
voltages above +3 V are treated as "high"

Typical applications:

Converting the levels of digital control signals (e.g. gate, trigger, clock) to another voltage level (+12V or +5V)
buffering and duplicating digital control signals (e.g. gate, trigger, clock)

Important note: the module cannot be used for analog signals.
Read more
MRP:$67.41 SAVE 17%
coming soon $56.17
FORTHCOMING
EMW MIDI Thru 4 Module (black faceplate)
Notes: The EMW MIDI Thru-4 was designed to help users with multiple MIDI modules. It lets you take 4 copies of a MIDI signal that can used with any of our EMW MIDI-enabled oscillators.

Eurorack (3U) form factor - 8 HP width
Power consumption: +12V [10mA] / -12V [0mA]
Weight: 69g
Depth: 50mm
Read more
MRP:$99.87 SAVE 20%
coming soon $80.11
FORTHCOMING
ADDAC System ADDAC301 Floor Control Module (red faceplate)
Cat: 776281
 
floor control module
Notes: While ADDAC were working on the new VC Stompboxes several expression pedals were tested and it became clear that most often, while playing a modular system, your hands are busy.
It's also normal to have an expression pedal lying around somewhere, so ADDAC have brought these back, cleaned up the dust and put them to good use.
This module allows the connection of any standard expression and sustain pedal.

The expression pedal action can be fine-tuned with Range and Offset knobs.
Range defines the voltage range (-10v, +10v).
Offset transposes the range by (-5v, +5v).
Two leds, plus and minus, monitor the CV Output
Positive and inverted output jacks.
The sustain pedal action will generate a gate signal on the gate output.
One led monitors this output.
The module also features a bus board +5v Adaptor, this will be able to provide +5v to any bus board.
This feature can be removed through a jumper on the back of the module.

Specs:
. Width: 4 HP
. Depth: 4 cm
. Max current: 20mA
. Bus Board Cable: 8 × 2 IDC (Doepfer style) connector
Read more
MRP:$74.90
coming soon $72.82
FORTHCOMING
Happy Nerding 2x SAM Dual Stereo Attenuator Mixer Module (black faceplate)
Cat: 777908 Rel: 31 Aug 20
 
dual stereo attenuator-mixer
Notes: 2xSAM is 4 HP Dual Stereo Attenuator-Mixer

Several 2xSAMs can be chained together or with other HN stereo modules via sockets on the back side.

2xSAM's total mix stereo output can be internally sent to the Isolator, PanMix Jr, 3xStereo Mixer, or can be received from OUT, PanMix, PanMix Jr, 3xStereo Mixer, or another 2xSAM.

If jumpers are not installed (placed on one pin only by default) the max gain is 1x. When the jumper is properly placed on both pins - the gain is 5x. There are four inputs thus four jumpers. Each jumper is relevant to its channel.

27 mA +12V
27 mA - 12V
35 mm Depth
4 HP wide
Read more
MRP:$106.11 SAVE 17%
coming soon $88.42
FORTHCOMING
Happy Nerding 3x MIA Six Channel Attenuverting Mixer Offset Scale Polariser Module (black faceplate)
Cat: 777911 Rel: 31 Aug 20
 
attenuverting mixer/offset/scale/polarizer module
Notes: 3xMIA is a 6-channel attenuverting mixer/offset/scale/polarizer.

3 blocks of 2-channel attenuverting mixers, using dual concentric pots. Each channel can be switched to mix with the subsequent channel, allowing for 2-2-2, 4-2, 6 mix configurations.

With nothing plugged into an input, an offset is normalled to that channel. The inner knobs control the A inputs, while the outer knobs control the B inputs.

DC coupled, so it can be used for audio, CV, or both at the same time.

80 mA +12V
80 mA -12V
35 mm Depth
6 HP wide
Read more
MRP:$116.10 SAVE 17%
coming soon $96.75
FORTHCOMING
Eurorack Hardware Modules AMIX Active Audio & CV Mixer Module (black faceplate) (fully assembled)
Notes: The AMIX module from Eurorack Hardware has three channel (active) powered mixer in 2HP for Eurorack. Great for both Audio and CV sources. Matte black panel with white graphics. Max gain of 1.
Current Draw: +12=15mA, -12=10mA, +5=0
Read more
MRP:$83.64 SAVE 19%
coming soon $67.61
FORTHCOMING
SynthRotek 308 Distortion Module (black faceplate) (fully assembled)
Cat: 778154 Rel: 06 Jul 20
 
distortion module
Notes: Get ready for the bright lights of the colosseum!

SynthTotek have taken the rock-solid RAT clone, squeezed it into a Eurorack module and added CV control over Gain. The 308 will take your playing to new heights with tremolo and other distortion modulation techniques.
Read more
MRP:$119.85 SAVE 19%
coming soon $96.74
FORTHCOMING
SynthRotek ECHO Voltage Controlled Echo Module (black faceplate) (fully assembled)
Cat: 778205 Rel: 06 Jul 20
 
voltage controlled echo module
Notes: The ECHO (formerly known as the EKO) is a compact voltage-controlled echo/delay comes in the very tidy size of 4HP and is certain to be one of the best bangs for your buck.

A very unique echo using the PT2399 IC featuring Voltage Controlled Rate. Manual controls for Rate, Feedback, and Mix. Beautiful and bizarre, CV modulation of the rate brings in ghostly pitch bent sounds to metallic reverbs. An effects module that everyone needs in their rig.

ECHO Rate CV accepts -5 / +5 voltages (although the negative range is almost -7)

ECHO Rate knob is setup to push the chip into extreme territory and will extend past the "useable" range of the PT2399 IC, meaning that once you turn the knob past 3 o'clock or so, the chip will stop operating and you'll only hear your dry signal.

Attenuation, attenuversion, or using an offset will greatly help when running voltages into the Rate CV input. This way, you can tailor the modulation as you see fit. You will absolutely get the most out of your ECHO by using modules that attenuate, invert or offset your signal.
Read more
MRP:$119.85 SAVE 19%
coming soon $96.74
FORTHCOMING
ADDAC System ADDAC213B Eurorack Bridge Module (black faceplate)
Notes: The ADDAC213B is the second pair of modules from ADDAC's Eurorack Bridge system.

A pair of ADDAC213Bs can be used in standalone to send/receive 8 CV or audio signals between different points inside the same case or as an expansion to the main pair of Eurorack Bridge modules, the ADDAC213As.

Two ADDAC213B modules can be connected to each other with the use of a single ribbon cable and then used inside a case to carry signals between distant points without the need for long cables. Less clatter, less spaghetti- more space of your fingers on those knobs!

ADDAC213Bs always come in pairs. A single pair can send & receive up to 8 CV or audio signals between different points in your case at the same time. The modules can be installed in normal position or a 180 degree position to fit any need.

As an Expansion to an ADDAC213A.

Each ADDAC213B connected to the backside of an ADDAC213A adds 8 more channels to the main bridging functionality of the ADDAC213A.

Up to 2 ADDAC213B can be connected to an ADDAC213A module, expanding the bridging between two difference cases to a total of 24 channels.

If you're looking for a simple one-cable bridge between your various cases, then look no further than the ADDAC213A.

Between the ADDAC213A pair and the ADDAC213B, your cases never looked so elegantly connected together!

Each module can be installed in normal position or at 180 degrees.

Mechanical:
. Format: Eurorack
. Width: 3 HP
. Depth: 2.5 cm

Electrical:
Passive / Does not draw current
Ribbon Cable: 50cm or 100cm ribbon cable
Read more
MRP:$86.14
coming soon $83.22
FORTHCOMING
EMW Phase 45 Analogue Phaser Module (black faceplate)
Notes: The EMW Phase 45 is a simple yet powerful analog 1-stage (45 ) phaser module. It features manual controls for Feedback and Phase as well as a CV input for Phase modulation (Mod In).

Eurorack (3U) form factor - 8 HP width
Power consumption: +12V [10mA] / -12V [10mA]
Weight: 86g
Depth: 50mm
Read more
MRP:$98.62 SAVE 21%
coming soon $78.03
FORTHCOMING
EMW Wave Stereolizer Module (black faceplate)
Cat: 775250
 
wave stereolizer module
MRP:$106.11 SAVE 20%
coming soon $85.30
FORTHCOMING
Division 6 Business Card Synthesizer (fully assembled)
Cat: 777973 Rel: 06 Jul 20
 
business card synthesiser
Notes: The Business Card Synthesizer is a tiny synth that can be connected to a Business Card Sequencer, other synth gear, or played by itself.

Headphones can be connected directly to the output of the synth, and there are plenty of knobs to play with, so you can easily make noises anywhere. Great for learning about synthesizers!

S&H Button: Enables Sample & Hold, which disables the external CV IN jack and uses LFO1 and LFO2 to determine oscillator pitch. LFO1 sets the sample rate (SHAPE is ignored for this), and LFO2 is the wave that gets sampled.

GATE Button: Manually turns on the gate so sound comes out of the synth. This control is momentary, but you can latch it on by tapping the S&H button while holding the GATE button down.

COARSE TUNE: Adjusts the pitch of the oscillator up or down in large increments

FINE TUNE: Adjusts the pitch of the oscillator up or down in fine increments

SHAPE: Changes the shape of the wave produced by the main oscillator (VCO). Turning this control fully CW gives you a triangle wave. Start turning it CCW takes you through sawtooth/ramp, then at about the 12:00 position you get a square wave. Continue turning it CCW and you get several higher duty cycle square waves
.
GLIDE: Adjusts the rate at which the pitch of the VCO takes to go between pitches (whether changed by the COARSE TUNE knob or CV IN). Fully CCW causes the pitch to react almost instantly, while fully CW makes it take its sweet time.

LFO 1 / LFO 2 SHAPE: Changes the shape of the waves produced by the low-frequency oscillators (LFOs). The shapes are similar to those of the VCO, except that the LFOs have sawtooth/ramp waves that go both up and down (since you can actually hear the difference at LFO rates).

LFO 1 / LFO 2 RATE: Controls how fast the LFOs go.

LFO -> VCO: Routes the two LFOs to control the pitch of the main oscillator. The 12:00 position is basically "off", and the LFOs have no effect on pitch. Start turning the control CCW and LFO1 starts changing the pitch of the VCO. Maximum effect is at about 10:00. Continuing to turn the control starts to bring in LFO2 as well. All the way CCW gives you full effect from both LFO1 and LFO2.

Turning the control CW from 12:00 does essentially the same thing, but brings in LFO2 first, then LFO1.

This might seem like kind of a weird control, but it gives you quite a bit of routing flexibility with one knob. You can have no pitch modulation, LFO1, LFO2, LFO1 with a little LFO2, or LFO2 with a little LFO1.

LFO -> VCA: Routes the two LFOs to control the amplitude of the oscillator. (See LFO -> VCO control description above for more information about how the control works.)

ATTACK: Controls how fast the audio amplitude fades in when the gate is triggered. CCW is fast and CW is slow.

DECAY: Controls how fast the audio amplitude fades out when the gate is released. CCW is fast and CW is slow.

VOLUME: Controls the overall volume of the signal coming from AUDIO OUT.

FILTER: Changes the cutoff frequency of an analog low-pass filter. Turn the knob fully CW and all frequencies (that you can hear) are let through. Start turning it CCW and the high frequencies start getting cut off, until the sound becomes muddy / muffled. Use in conjunction with the SHAPE control to get the tonal quality you are looking for.

Connections:
CV IN: Accepts a 1 volt/octave control voltage to control the pitch of the oscillator. It responds from about 0-5V, but voltages outside of this range won't cause damage. The CV input is quantized, so only valid (western scale) notes are played. This input is ignored when Sample & Hold is enabled.
GATE IN: A voltage greater than about 2.5V will turn on the gate and allow audio to come out the output of the synth.
AUDIO OUT: Connect to an amplifier or another synth. The jack has both the tip and ring connected, so you can even use stereo headphones and hear sound from both ears.
Power: Connect 7.5-15VDC to this 3.5mm TS jack to power the synthesizer. The tip is positive (don't worry, there's a protection diode in case you get it reversed). You can get power from a 9V battery, AC adapter, or you may even be able to find an output on your modular synthesizer that can provide enough current.

Specifications:
Power supply: 7-15VDC (reverse-polarity protected!)
Power connection: 3.5mm phone jack, center-positive
Current draw: 15ma
Dimensions: 3.5" x 2" (the same as a business card!)
Read more
MRP:$103.62 SAVE 19%
coming soon $84.25
FORTHCOMING
EMW 8-Step Trigger Sequencer Module (black faceplate)
Notes: The EMW 8-Step Trigger Sequencer combines many different features into a wellsized 8hp module. This module let’s you program 8 different sequences that can be used to trigger drum modules, envelopes or function generators. The module includes clock, reset, and hold CV inputs as well as a "Beat-1" trigger output that sends out a trigger whenever the sequencer goes through Step #1.

Eurorack (3U) form factor - 8 HP width
Power consumption: +12V [38mA] / -12V [0mA]
Weight: 119g
Depth: 50mm
Read more
MRP:$118.60 SAVE 22%
coming soon $92.59
FORTHCOMING
EMW MIDI Mixer Module (black faceplate)
Notes: The EMW MIDI Thru-4 was designed to help users with multiple MIDI modules. It let’s you take 4 copies of a MIDI signal that can be used with any of our EMW MIDI-enabled oscillators.

Eurorack (3U) form factor - 8 HP width
Power consumption: +12V [34mA] / -12V [15mA]
Weight: 73g
Depth: 50mm
Read more
MRP:$103.62 SAVE 19%
coming soon $84.27
FORTHCOMING
ADDAC System ADDAC301B Dual Expression Pedal Attenuator Module (red faceplate)
Cat: 776289
 
dual epression pedal attentuator
Notes: Passive dual expression pedal attenuator.

Plug any CV or audio source through it and control its amplitude through any standard expression pedal.

Invert switch for inverting the expression pedal action.

Specs:
. Passive Module
. Width: 4 HP
. Depth: 3 cm
Read more
MRP:$69.91
coming soon $67.61
FORTHCOMING
SynthRotek Arcadian Rhythms Module (black faceplate, blue buttons) (fully assembled)
Cat: 778164 Rel: 06 Jul 20
 
arcade button module
Notes: Arcadian Rhythms is an arcade button module that can be used to trigger drums, envelopes and other events in a Eurorack system. When the buttons are pressed, they light up and send a gate. As long as a button is held down, the gate remains high.

Mix and match your LED buttons! The brightness between colors will vary slightly, but the trimmers on the back of the module will adjust the LED brightness so the three buttons match. Reducing the brightness will also reduce the current draw (each button draws 41mA at full brightness).

Choose red, blue, green, yellow or white buttons.

Specifications:
Module width: 35mm
Module depth: 6HP
Current draw: +12V: 123mA max (41mA per button)
Read more
MRP:$66.17 SAVE 18%
coming soon $54.09
FORTHCOMING
Happy Nerding 2x SAM Dual Stereo Attenuator Mixer Module (silver faceplate)
Cat: 777876 Rel: 31 Aug 20
 
dual stereo attenuator mixer module
Notes: 2xSAM is 4 HP Dual Stereo Attenuator-Mixer

2xSAM's total mix stereo output can be internally sent to the Isolator, PanMix Jr, 3xStereo Mixer, or can be received from OUT, PanMix, PanMix Jr, 3xStereo Mixer, or another 2xSAM.

If jumpers are not installed (placed on one pin only by default) the max gain is 1x. When the jumper is properly placed on both pins - the gain is 5x. There are four inputs thus four jumpers. Each jumper is relevant to its channel.

27 mA +12V
27 mA - 12V
35 mm Depth
4 HP wide
Read more
MRP:$96.13 SAVE 17%
coming soon $80.11
FORTHCOMING
Happy Nerding 6x MIX Six Channel Audio Mixer Module (silver faceplate)
Cat: 777890 Rel: 31 Aug 20
 
audio mixer module
Notes: 6xMIX is a six channel audio (AC coupled ) mixer, channels arranged in three groups with separate outputs having led indicators. Each group can be switched to mix with the subsequent group, allowing for 2-2-2, 4-2, 6 mix configurations. The module can also be used to mix two stereo channels plus separate group of two mono channels. Perfect audio performance with the lowest noise and distortion amounts.

The inner knobs control the A inputs, while the outer knobs control the B inputs.

50 mA +12V
50 mA -12V
35 mm Depth
6 HP wide
Read more
MRP:$116.10 SAVE 17%
coming soon $96.75
FORTHCOMING
EMW Multi Low Frequency Oscillator Noise Module (black faceplate)
Notes: The EMW MULTI LFO-NOISE is another very interesting module: it has a selection of 8 waveforms, including noise, in order to maximize the modulation capabilities of your modular synthesizer setup. When used in conjunction with another LFO (via a DC mixer), the resulting waves can be very varied and random.

Read more
MRP:$86.14 SAVE 19%
coming soon $69.70
FORTHCOMING
EMW Boozy Voltage Controlled Filter Module (black faceplate)
Cat: 774642
 
voltage controlled filter module
Notes: The EMW Boozy VCF is a specially designed 6dB/oct voltage controlled filter with an unique and interesting sound. It was not designed to replace any standard VCF module but it's ideal to create more sound variations in a modular system. When the cut off frequency is adjusted to it's minimum the sound is not completely muted. This feature summed to its special resonance actuation curve adds one more option to your timbres.
Read more
MRP:$112.36 SAVE 19%
coming soon $90.51
FORTHCOMING
Happy Nerding 3x Stereo Mixer Module (silver faceplate)
Cat: 777869 Rel: 31 Aug 20
 
stereo mixer module
Notes: Stereo Mixer is a high quality 3 channel stereo mixer with manual volume controls. Total mix Left and Right outputs available on separate jacks, plus L&R stereo jack can be used to route the mix via single stereo cable or drive the headphones. Channels 1 and 2 can be muted with the relative switches. Left and Right led indicators available for all three channels.

All left channel inputs normalled to be used as mono inputs.

Several 3x Stereo Mixer modules can be chained together via connections on the back side. This connection is possible with other Happy Nerding stereo modules too. At the moment PanMix Jr and 3x Stereo Mixer can be connected in both ways. Also their stereo outputs can be internally sent to the Isolator module. Or stereo signal can be received from OUT and latest revision of PanMix.

50 mA +12V
50 mA - 12V
35 mm Depth
6 HP wide
Read more
MRP:$116.10 SAVE 17%
coming soon $96.75
FORTHCOMING
Happy Nerding 3x MIA Six Channel Attenuverting Mixer Offset Scale Polarizer Module (silver faceplate)
Cat: 777880 Rel: 31 Aug 20
 
attenuverting mixer/offset/scale/polarizer
Notes: 3xMIA is a 6-channel attenuverting mixer/offset/scale/polarizer

3 blocks of 2-channel attenuverting mixers, using dual concentric pots. Each channel can be switched to mix with the subsequent channel, allowing for 2-2-2, 4-2, 6 mix configurations.

With nothing plugged into an input, an offset is normalled to that channel. The inner knobs control the A inputs, while the outer knobs control the B inputs.

DC coupled, so it can be used for audio, CV, or both at the same time.

80 mA +12V
80 mA -12V
35 mm Depth
6 HP wide
Read more
MRP:$116.10 SAVE 17%
coming soon $96.75
FORTHCOMING
Happy Nerding 6x Mix Six Channel Audio Mixer Module (black faceplate)
Cat: 777917 Rel: 31 Aug 20
 
audio mixer module
Notes: 6xMIX is a six channel audio (AC coupled ) mixer, channels arranged in three groups with separate outputs having led indicators. Each group can be switched to mix with the subsequent group, allowing for 2-2-2, 4-2, 6 mix configurations. The module can also be used to mix two stereo channels plus separate group of two mono channels. Perfect audio performance with the lowest noise and distortion amounts.

The inner knobs control the A inputs, while the outer knobs control the B inputs.

50 mA +12V
50 mA -12V
35 mm Depth
6 HP wide
Read more
MRP:$116.10 SAVE 17%
coming soon $96.75
FORTHCOMING
Citronic CM25 Studio Condenser Microphone
Citronic CM25 Studio Condenser Microphone (studio condenser microphone)
Cat: 778591 Rel: 31 Aug 20
 
large diaphragm condenser microphone
Notes: Large diaphragm condenser microphone with cardioid polar response pattern for accurate reproduction of vocals and instruments in a recording or broadcast studio. All metal construction with a bespoke shock-mount and magnetic pop-shield included, ready to mount to a standard microphone stand or boom arm. Connection via XLR for high quality balanced audio output and phantom power from a mixing console or dedicated phantom power supply. Supplied with a 3m balanced XLR lead in a fitted aluminium transit case.

The box for this item contains :

CM25 condenser microphone
Fitted shock-mount cradle
Magnetic pop shield
3m balanced XLR lead
Aluminium transit case

Power supply: 30 - 48V phantom power (via XLR)
Construction: Zinc alloy body and steel grille
Capsule: 25mm: O nickel sputtered diaphragm
Output impedance: 2.2k Ohm
S/N ratio: 68dB (A-weighted)
SPL max.120dB (1kHz)
Lead length: 3m
Read more
MRP:$86.14 SAVE 31%
coming soon $59.29
FORTHCOMING
Grado Prestige Black3 Phono Cartridge & Stylus (standard mount)
Cat: 780755 Rel: 16 Sep 20
 
Cartirdge & stylus
Notes: The Black3 uses a three piece OTL cantilever that has a Grado specific diamond mounted on a brass bushing.

What's the difference between Black2 and Green2?
Approximately 15% of the Black3 production run meet higher specifications. These are hand selected from the batch and designated as Green3.

Grado's OTL, or optimized transmission line, technology provides an ideal transfer of signal from the surface of the LP to the generator of the system. This technology rejects unwanted resonances and lowers distortion preserving the fundamental and harmonic frequencies of the music. This also helps keep noise generated by the motor system in the cartridge to a minimum.

Grado's OTL stylus/cantilever design makes records sound quieter, improves the height, width, and depth of the soundstage, and present more detail than previously obtainable.

The Black3 is hand assembled by Grado's team in Brooklyn, with some builders having over 25 years of experience. This updated series of cartridges offers excellent tonal balance, dynamics, and realism, for a most rewarding reproduction of vocals and instruments. The coil winding techniques using ultra high purity copper wire, which were honed during the development of the Lineage Series, have let the electrical circuits achieve unison between the four coils in each phono cartridge. This allows for a precise balance between channels and accurate stereo imaging.

As in all Grado phono cartridges the Black3 is powered by a twin magnet system that optimizes the balance between stereo channels. All internal magnetic circuit parts are held to extremely high tolerances creating the desired stereo imaging. Grado's patented Flux-Bridger design allows the Black2 to have one of the lowest effective moving mass generating systems while creating an excellent balance throughout the full frequency range.
Read more
MRP:$93.63 SAVE 17%
coming soon $78.03
FORTHCOMING
EMW Gate Delay Module (black faceplate)
Notes: The EMW GATE DELAY module can induce a delay on a gate signal. The delay amount can be adjusted using the SET and RESET knobs on the front panel. A delayed gate signal or pulse is very useful to promote the trigger of envelopes and other modules in alternative moments in a patch, creating some very interesting and unexpected effects and modulations.

Eurorack (3U) form factor - 6 HP width
Power consumption: +12V [29mA] / -12V [0mA]
Weight: 64g
Depth: 50mm
Read more
MRP:$102.37 SAVE 20%
coming soon $82.18
FORTHCOMING
EMW 10V Level Converter Module (black faceplate)
Notes: 8-cannel voltage converter

Eurorack (3U) form factor
Read more
MRP:$93.63 SAVE 20%
coming soon $74.90
FORTHCOMING
EMW Stereo Enhancer Module (black faceplate)
Cat: 775266
 
stereo enhancer module
Notes: The EMW Stereo Enhancer let’s you control the stereo width of an incoming stereo audio signal. The module contains 2 inputs (L and R), 2 outputs (L and R) as well as Input Level and Stereo Width controls.

Eurorack (3U) form factor - 6 HP width
Power consumption: +12V [6mA] / -12V [6mA]
Weight: 68g
Depth: 50mm
Read more
MRP:$106.11 SAVE 23%
coming soon $82.18
FORTHCOMING
SynthRotek Cosmic ECHO Delay Pedal (fully assembled)
Cat: 778344 Rel: 06 Jul 20
 
delay pedal
Notes: The Cosmic ECHO is an analog-sounding lofi delay that will work with just about anything you plug into it. The dark, lush, moody tones of the ever-popular PT2399 IC provide an out-of-this-world experience. This new take on this classic pedal pushes the chip's limits so you can explore all the gritty elements drifting at the edge of long delay rates. It already outperforms other bucket brigade style echoes, but just to be sure, we added 2 momentary switches, Zone and Warp.

Contains PT2399 IC, a bucket brigade style emulation. This IC has 16-bit sampling for 30-300 milliseconds. After that, the sample rate goes down in relation to the delay length. This results in artifacts and noise being introduced into the audio for weird, cosmic, psychedelic sounds.

Read more
coming soon $97.79
FORTHCOMING
SynthRotek 1U Unity Gain Mixer Module (black faceplate)
Cat: 777893 Rel: 06 Jul 20
 
mixer module
Notes: The 1U Unity Gain Mixer adds input signals together and combines them for a summed output. For example, if you put in a 1V source and a 3V source, the output will be 4V. It's mainly used for CV, but it can be used to combine audio signals together.

A unity gain mixer is handy in several ways:
Combining gates and triggers. Plug a few sequencer steps into the unity gain inputs, then run the output to a drum synth, VCA, envelope, etc.
Re-shaping two CV sources with a single envelope
Combining different wave shapes or LFOs to make crazy sounds.
Controlling the CV of one source with the CV of another source. Just plug the CV out of a sequencer into and an expression pedal/touchable CV out into the unity gain inputs.

Specifications:
Current draw:
18 mA +12V
18 mA -12V
0 mA 5V
Depth: 32 mm
Width: 20HP

Please note: Synthrotek's 1U products do not fit in Vermona or Intellijel cases.
Read more
MRP:$83.64 SAVE 19%
coming soon $67.61
FORTHCOMING
EMW 4-CH Stereo Mixer 4 Channels Stereo DC & Audio Mixer Module (black faceplate)
Notes: The EMW 4-CH DC/Audio mixer can mix DC, slow frequency waveforms and audio signals into LEFT, RIGHT and Stereo outputs, creating panoramic stereo images to your sounds. It can also be used to mix audio range VCO signals and LFO waveforms in order to create complex and chaotic modulations. In any case, the EMW 4-CH Stereo Mixer is a very handy module that can help you to create and precisely manage your patches with a very clean sound.
Read more
MRP:$111.11 SAVE 27%
coming soon $81.15
FORTHCOMING
ADDAC System ADDAC217 Quad Gate to Trigger Module (black faceplate)
Cat: 776261
 
gate to trigger module
Notes: Following ADDAC System's T-Networks series, the importance of having the right input signal for firing drum modules or envelopes was realised. Gates and Triggers are often looked at as similar signals but at times it really makes a difference and results will change drastically depending if a Gate or a Trigger is fed to the input of such modules.

This led to the simple yet effective Gate to Trigger.
A four channel converter with bypass switch for each channel.

Any input Gate will be limited to a 1ms Trigger.

Tech Specs:
3HP
2.5 cm deep
10mA +12V
10mA -12V
Read more
MRP:$74.90
coming soon $72.82
FORTHCOMING
EMW Echo Effects Module (black faceplate)
Notes: This is a digital Echo module designed to have a very vintage and analog style sound. It adds a very dist inct ive and interest ing sound characteristic to any setup.
Read more
MRP:$111.11 SAVE 22%
coming soon $86.35
FORTHCOMING
EMW Wave Compressor Module (black faceplate)
Cat: 775242
 
wave compressor module
Notes: The WAVE COMPRESSOR is a module which is intended to compress and limit the final level of any waveform or mix that must not exceed levels around 10 Volts. Its action can be adjusted to fit all major signals inside a modular system and it is very useful to avoid distortion and to promote a dense sound in many patches. It can also be used with noise and drums modules to give an extra ‘punch’ to percussive sounds.

Eurorack (3U) form factor - 8 HP width
Power consumption: +12V [15mA] / -12V [7mA]
Weight: 87g
Depth: 50mm
Read more
MRP:$118.60 SAVE 22%
coming soon $92.59
FORTHCOMING
EMW Logic 101 Logic Functions Module (black faceplate)
Notes: The EMW Logic 101 module has 4 different logic functions that are useful when you need to control pulses in order to create alternative activation logic. The «&" or "AND" function output only goes high when both A and B inputs are on a high level. The "OR" function output goes high when either A or B inputs are on high level. The verters,as expected, inverts the signal in its outputs, going high when the input is low and vice-versa.

Eurorack (3U) form factor - 6 HP width
4 logic functions In only 6HP rack space
2 x AND function, 1 x OR and 2 x Inverter
External pulse input: 2.5 to 15 Volts.
Power consumption. +12V [34mA] / -12V [0mA]
Connectors: 3.5mm
Weight: 72g
Depth: 50m
Read more
MRP:$116.10 SAVE 20%
coming soon $92.59
FORTHCOMING
EMW Clock Counter/Separator Module (black faceplate)
Cat: 775642
 
clock counter & seperator module
Notes: The EMW Clock Counter / Separator module counts a certain number of pulses coming into it's CLK IN jack and distribute them to 4 different outputs. With the "COUNTER" knob set to "4", the first 4 incoming pulses will be routed to OUT 1. The next 4 pulses will be routed to OUT 2, the next 4 to OUT 3, and the last 4 will go to OUT4. Any clock source can be distributed to several modules in sequence. You can reduce the separation from 4 to 3, 2 or 1 channel by just patching a cable from one output to a previous input.

18 mA +12V
10 mA -12V
50 mm deep
Read more
MRP:$116.10 SAVE 20%
coming soon $92.59
150/158(ページ1/4)の商品
1  2  3  4  »

Filter

Coming Soon: Studio Equipment
Close