安全なお買い物

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

安全なお買い物

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Four Weeks: All Genres

View:
Options
17/7(ページ1/1)の商品
Cat: 577767 Rel: 10 Jul 19
 
Voltage-controlled 24 dB low-pass filter - 8HP
Notes: Module A-120 is a voltage controlled low-pass filter, which filters out the higher parts of the sound spectrum, and lets lower frequencies pass through. The Cut-Off Frequency determines the point at which filtering takes effect. You can control this manually, or by voltage control (filter modulation, for instance by an LFO). Three CV inputs are available, and the sum of the voltages from these affects the filter cut-off.

The module is based on a so-called "transistor ladder" design, with a cut-off slope of -24 dB/octave, as in various Moog synthesizers. That's what gives it its classic, legendary Moog sound.

Resonance (or Emphasis) is adjustable all the way up to self-oscillation - in which case the filter behaves like a sine wave oscillator.
Read more
 1 in stock $103.41
Click for better price!
quote 577767
Cat: 734880 Rel: 10 Jul 19
 
Envelope module with two ADSR voltage controlled enevelope generators - 8HP
Notes: The module contains two ADSR type voltage controlled envelope generators with exponential curve shapes (charge/discharge curves of a capacitor) behind a front panel with 8 HP only.

Each ADSR provides these controls and in/outputs:

- LED (displays the envelope output)
- A: manual Attack control
- D: manual Decay control
- S: manual Sustain control
- R: manual Release control
- Gate Input
- Retrigger Input
- CVT Input with attenuator (CVT = CV Time)
- Envelope Output 1
- Envelope Output 2

The output voltage range for each envelope is 0 - 10V (10V = attack peak).

The time range of Attack/Decay/Release is about 1ms to 30s.

By means of internal jumpers one can select which time parameters are controlled by the CVT input (e.g. D only or D+R or A+D+R) and in which direction (i.e. if an increasing CVT shortens or stretches the time parameter in question).

Socket CVT can be normalled to an internal fixed voltage (i.e. the switching contact is connected to an internal fixed voltage). That way it's possible to change all time parameters simultaneously by means of the CVT control.

Another jumper is used to set output 2 to normal or inverted envelope.

And another jumper is used for the normalling of Gate 2 to Gate 1 (i.e. ADSR#2 is also triggered by Gate 1).

Two more jumpers are used for the optional bus access to the gate signal of the bus for each ADSR.
Read more
 5 in stock $120.99
Cat: 738619 Rel: 09 Jul 19
 
Voltage controlled envelope generator, standard edition - 14HP
Notes: The A-141-2 module is an ADSR envelope generator with voltage controlled attack, decay, sustain and release parameters. Other features include LFO functionality as well as digital end-of-attack and end-of-release outputs. Besides positive and inverted outputs there is an output with voltage controlled amplitude available.

Attack, Decay, Sustain and Release parameters of the A-141-2 can be adjusted manually as well as via control voltages. The CV inputs come equipped with attenuators. In addition, a Comm-CV socket was implemented. Control voltages fed to this input influence all time parameters (A, D and R) simultaneously. Thus, it is possible to make high pitched notes shorter and more percussive. - Just like the behaviour of many acoustic instruments. The time range of the envelope goes from 50 microseconds to six seconds. Using a toggle switch, it is possible to increase these values by a factor of ten (500 us to 60 s) or a factor of hundred (5 ms to 10 min). To activate the envelope, there are gate and retrigger inputs.

The A-141-2 is equipped with a normal and an inverted output. Both connectors work with a fixed level. Furthermore, there is a third, variable output. Here, before reaching the out socket, the envelope signal is fed to a voltage controlled VCA. - Perfect for velocity CV signals. A jumper on the circuit board allows you to choose between a unipolar and a bipolar mode of operation. Other jumpers make it possible to normalize the CV inputs.

Last but not least, there are two digital outputs called EOA and EOR, which emit a gate signal after the attack respectively release phase. This is useful for delayed triggering of other envelopes. By connecting EOA or EOR output to the gate input, you can make the A-141-2 oscillate like a LFO. Adjustments to the envelope times change the frequency and waveform. If you connect the Attack CV input to the inverted output or the Decay respectively Release CV input to the normal output, you can alter the curve characteristics.
Read more
 1 in stock $138.57
Click for better price!
quote 738619
Cat: 738636 Rel: 09 Jul 19
 
Simplistic quad LFO module with intuitive front panel - 14HP
Notes: Module A-143-3 is a low-cost four-fold modulation oscillator, often called LFO (low frequency oscillator). Like the other modules of the A-143 series (A-143-1 and A-143-2) not a very "exciting" module, just a bread-and-butter device and a simple demon for work. The module contains four simple LFOs. Each LFO is equipped with three waveform outputs: triangle, rectangle and rising sawtooth. The frequency of the sawtooth output is twice the frequency of the other outputs. A three-way switch is used to select one of three frequency ranges mid-low-high, spanning from about two cycles per minute at the lowest, to moderate audio frequency at the highest (about 5 kHz).

If other waveforms or additional LFO features are required (e.g. reset input, adjustable waveform, voltage controlled frequency) the LFO modules A-145, A-146 and A-147 are available.
Read more
 1 in stock $115.82
Click for better price!
quote 738636
Cat: 738649 Rel: 10 Jul 19
 
Multi-function module with LFO, switchable VCA, & VC delay - 8HP
Notes: Module A-147-2 is the successor of the VCLFO A-147 but offers much more features than the predecessor. The module is made of these sub-units:

- VCLFO: voltage controlled low frequency oscillator
- VCA: voltage controlled amplifier, switchable to voltage controlled polarizer
- VC delay unit: voltage controlled linear attack envelope (only one parameter: attack) for delayed LFO operation in combination with the VCA (e.g. delayed vibrato/tremolo)

LFO: The voltage controlled LFO has the waveforms Triangle, Sine, Sawtooth and Rectangle available and features a Reset/Sync input. Triangle/Sine and Rectangle are displayed by means of dual-colour LEDs (probably red/green), Sawtooth has a unicolor LED available (probably blue). The output levels are about -4V...+4V for Triangle, Sine and Rectangle. The Sawtooth level is about 0...+8V. The CV control can be switched to attenuator or polarizer ("CV Mode" switch). In polarizer mode the CV inputs affects the frequency in the reverse manner when the CV control is left from the centre position. In the centre position CV has no effect and right from the centre the control works like a normal attenuator. The frequency range (without external CV) is from about 0,005 Hz (i.e. about 3 minutes per period) to 200 Hz (with external CV max. frequency about 1kHz). In addition a ultra-low mode can be activated by means of an internal jumper. When the ultra-low jumper is set a fixed voltage is connected to the switching contact of the "LFO CV" socket. In polarizer mode of the CV control that way extremely low frequencies (up to one hour period and more) are possible. For this a jumper has to be installed on the pin header JP6. In the factory a dummy jumper is installed on the pin header JP7 "Dummy". JP7 has no function and is used only for "parking" of the jumper. Simply remove the jumper from JP7 and plug it on JP6. JP6 is located behind the CV control.

VCA: This is a linear VCA that can be switched to "normal" VCA (i.e. kind of a voltage controlled attenuator) or voltage controlled polarizer ("VCA Mode" switch). In the "normal" VCA mode amplification +1 is achieved with about +5V control voltage. In polarizer mode the amplification ranges from about -0.5 (i.e. inverted signal with about 50% level) with 0V CV to +0.5 (i.e. non-inverted signal with about 50% level) with +5V CV. With about +2.5V CV the signal is suppressed. Details about the functioning of a voltage controlled polarizer can be found in the description of the module A-133. In this mode the VCA can be treated also a DC coupled ring modulator (similar to A-114).

The VCA of the A-147-2 has three sockets available: "In" (signal input), "Out" (signal output) and "CV" (control voltage input).

The Triangle Output of the LFO is normalled to the VCA signal input by means of the switching contact of the "VCA In" socket. If another LFO waveform (or any other signal) should be processed by the VCA the corresponding signal has to be patched to the "VCA In" socket. The VCA can be used also independently from the LFO and the Delay CV. In this case the VCA sockets In, Out and CV have to be patched accordingly. The VCA can be used also as waveshaper for the LFO signals (e.g. by patching VCA In and VCA CV to different LFO signals, if necessary via attenuator A-183-1 or offset generator/attenuator A-183-2).

Attack/Delay: The third sub-unit of the module is a simple, voltage controlled envelope generator that has only the parameter "Delay" (or Attack) available. This unit generates a linear increasing voltage that starts from 0V after each Delay Reset until it reaches about +5V. Then the voltage remains at +5V until the next Delay Reset occurs. The inclination or gradient is controlled by the manual Delay control and the Delay control voltage ("Delay CV" input). The waveform is linear, the control scale is exponential. The output voltage is displayed by a green LED and available at the "Delay Out" socket.
Read more
 1 in stock $123.06
Cat: 738558 Rel: 16 Jul 19
 
3-way FX pedal switcher & mixer
Notes: EHX's Tri Parallel Mixer is a powerful effects creation and mixing hub. Three separate FX loops with flexible controls allow for multiple configurations, as follows:

- Run up to three FX Loops in parallel and create sounds that are not possible by connecting effects in series.
- Switch seamlessly between FX Loops in XOR mode
- Send one instrument out to three separate amplifiers
- Mix three instruments into a single output.

The Tri Parallel Mixer is surprisingly compact considering the level of functionality it provides, while its intuitive controls and I/O make it easy to operate. The Tri-Parallel Mixer comes with an EHX 9.6DC power supply.
Read more
 1 in stock $125.12
Click for better price!
quote 738558
Cat: 737544 Rel: 26 Jun 19
 
All-analogue distortion & lowpass filter - 4HP
Notes: Viol Ruina is an all-analogue distortion and lowpass filter with an internal envelope follower and self-modulating cutoff. The four-pole design is reminiscent of the classic filters we all know but with a completely new and slightly ridiculous twist. The independently addressable distortion circuit takes VR into overdriven paradise with a shocking amount of drive. Built-in envelope following makes an easy way to create dynamic patches with the flick of a switch, and feedback FM takes VR to a whole new realm of filthiness. Run a sound through VR, you'll get something cool out of it.
Read more
 1 in stock $127.19
Click for better price!
quote 737544
17/7(ページ1/1)の商品

Filter

Four Weeks: All Genres
Close