Back catalogue: All genres

Notes: A-180-9 is another simple but useful tool. It can be used to connect up to 14 signals between different cases by means of standard network cables (RJ45). These cables are available all over world smoothly in different lengths and colours. From the factory two black network cables with 0.5 m length are enclosed.

The upper network connector is wired to the eight sockets 1-8, the lower to the six sockets A-F. That way it's possible to pre-patch different cases and connect signals, that are required in all cases (e.g. clock, start/stop, master CV) by means of one or two cables only instead of 14 individual patch cables. When only eight signals are required only the upper network connector is required and the sockets 1-8 are used. When more than eight signals have to be patched both network connectors have to be used. It's also possible to wire the upper and lower network to different cases (i.e. signals 1-8 to external case #1 and signals A-F to external case#2).

The module is fully passive (no power supply required) and simply wires the 14 sockets to 14 pins of the network connectors.

The A-180-9 comes in pairs for combining two modular systems.

Notes: USB/MIDI to clock interface that allows for synchronizing clock-driven modules with the MIDI environment. It processes only the Clock, Start, Stop and Continue MIDI commands. It has several clock divider outputs, each one start, stop and reset outputs for controlling sequencers and also an interesting wait function. Input is either a 5-pin DIN socket or USB.

Notes: Module A-192-2 contains two independent CV/Gate-to-Midi/USB interfaces. For each of the two sub-units these inputs are available:

- Gate Input (min. +5V)
- CVN Input (defines the Midi note number), 1V/octave standard, range 0...+10V (i.e. 10 octaves)
- CVV Input (defines the velocity value assigned to the Midi note message), can be used alternatively for Midi volume (CC#7), range 0...+5V
- CVC Input (free assignable to any Midi control change number), range 0...+5V

For both sub-units a common CV Transpose input is available (1V/octave, range 0...+10V). The voltage applied to this input is added internally to CVN before the Midi note number is generated. It can be used e.g. to transpose two sequences simultaneously by one voltage.

How it works:

Whenever the rising edge of the Gate input is recognized a Midi note on message is generated. The note number corresponds to the sum of the voltages applied to the CVN input and the common CV Transpose Input that is present at the rising edge of the gate signal.

Notes: Module A-199 is a spring reverb module. The reverb effect is electronically simulated by means of 3 spiral springs. Spring reverb systems have a very characteristic sound that is based on the (insufficient) mechanical properties of the springs like signal delays, audio resonances, limited frequency range, acoustic feedback behaviour, sensitivity to mechanical shocks and others.

The 3-spring system used in the A-199 ensures a "dense" reverb because of the different properties of the three springs.

The A-199 implies some special features that are not self-evident for spring reverb units:

The reverb signal can be fed back to the input using the Feedback control. Even self-oscillation of the springs similar to the self-oscillation of filters is available. The feedback loop can lead even via external modules like VCA, VCF, phaser, frequency shifter, vocoder, distortion/waveshaper, ring modulator and others. In this case the reverb output of the A-199 is connected to the input of the external module(s) and the output of the external module(s) is fed back to the Ext. Feedback In socket of the A-199. This socket contains a switch that interrupts the internal feedback loop as soon as a plug is inserted.

Another feature is the Emphasis control. This enables the adjustment of the accentuation of middle frequencies (around ~ 2kHz).

With the Mix control the relation between original and reverb signal appearing at the mix output is adjusted.

Using all these features very extreme and unusual effects can be generated with the A-199.

Notes: Incredible sounding VCO module that helps you get incredibly rich signals out of your synthesizer. The Dreadbox Hysteria VCO features a huge frequency range of 16hZ to 32kHz. This gives you a lot of functional pitch to work with, allowing you to explore the sounds capable from this module.

The sounds themselves rest on a variable waveform selector - meaning you can scroll through the waveforms and blend them together. This can even be CV controlled, so you can obtain an evolving sound that changes over time. The modules in the Chromatic series give you a great starting point in the world of modular synths and are a must-have for beginners and professionals alike.

Power Consumption: 114mA @ +12V , 46mA @ -12V
10HP
35 mm deep

Notes: 4-input VCA stereo mixer w/ pan, stereo out, metering

50mm deep

Notes: VCA 3X is a simple yet great solution for synth users looking to add more VCAs to their setup in a single and compact module. This module features 3 VCAs with individual Signal and CV inputs and outputs.

Notes: Running Order is a two track trigger sequencer. It can be a precise master clock or manipulate incoming clock signal and works great in use as a sub-sequencer/divider in your Eurorack environment.

Zero-jitter clock generation: less than 50 microseconds internal clock jitter
101 style 1/16th note input mode (step/rest) with manual or CV controllable amount of triggers repeats when the active trigger step happens
Euclidean mode enabled for each track where we set Euclidean total steps amount in the circle and then amount of triggers happening in that circle.
Per step trigger probability in 101 mode and global probability in Euclidean mode.
Separate synchronization (reset) inputs, sync for track 1 is normalled to sync track 2
Clock divider for incoming external clock allows to quickly obtain various musical divisions on the fly incl. triplets of course, but more importantly tuplets mode allows you to stretch desired amount of triggers happening into a single bar
Separate mute buttons for each track
8 patterns of triggers sequences stored in the module and recalled on the next power up
Available in 3U / 6HP version

Power consumption:
30 mA +12V
10 mA -12V
0 mA 5V

Dimensions
22 HP
26mm deep with power ribbon cable connected

Notes: Running Order is a two track trigger sequencer. It can be a precise master clock or manipulate incoming clock signal and works great in use as a sub-sequencer/divider in your Eurorack environment.

Zero-jitter clock generation: less than 50 microseconds internal clock jitter
101 style 1/16th note input mode (step/rest) with manual or CV controllable amount of triggers repeats when the active trigger step happens
Euclidean mode enabled for each track where we set Euclidean total steps amount in the circle and then amount of triggers happening in that circle.
Per step trigger probability in 101 mode and global probability in Euclidean mode.
Separate synchronization (reset) inputs, sync for track 1 is normalled to sync track 2
Clock divider for incoming external clock allows to quickly obtain various musical divisions on the fly incl. triplets of course, but more importantly tuplets mode allows you to stretch desired amount of triggers happening into a single bar
Separate mute buttons for each track
8 patterns of triggers sequences stored in the module and recalled on the next power up
Available in 3U / 6HP version

Power consumption:
30 mA +12V
10 mA -12V
0 mA 5V

Dimensions:
22 HP
26mm deep with power ribbon cable connected

Notes: The power module from Endorphin.es is a module for the power supply of smaller modular systems such as skiff cases up to 104 TE width. The module consumes DC power between 12 and 20 volts from an external power supply unit. Voltages of up to +1000 mA and -700 mA are output, also depending on how strong the connected power supply is. In addition, there are two passive multiples.

Notes: The ZONE B.F. module is an element of the Capsule TITAN. Zone basses frequences stands for low frequency zone. This module is composed of 2 LFOs, both LFOs have 16 sync-able waveforms.

Speed : speed of the LFO, range from 0.1 Hz to +/-200 Hz
Wave (LFO 1 & 2) : 16 Syncable waveforms

The ZONE B.F. (black edition onwards) now features an additional mode. On the back of the PCB you will find two jumpers, marked as JP1. CV1 is LFO channel 1 and CV2 is LFO channel 2. By moving the jumper so it sits on one leg (rather than 2 as when you have received the module), the Sync input for either LFO channel now becomes LFO speed input, controllable via CV.

Tech Specs

- SYNC 1 & 2 : LFO waveform is reset when an impulse signal is received
- OUT 1 & 2 : LFO signal outputs 1 & 2
- Voltage swing is -/+5V
- LEDs display LFO activity
- Eurorack 5 HP
- Metal pot, panel mounted, screwed
- Consumption: +12V 40mA, -12V 10mA

Notes: Take a DJ-mixer-style combined high-pass and low-pass filter, cram it into Eurorack and you have the DJ VCF. A simple formula, but one perfected by Erica's attention to detail, with CV control and adjustable resonance.

Supplier's Notes:
As its name suggests, the Erica Synths Black DJ VCF provides sound treatment functionality typically found on DJ decks - it is fully open when the cutoff knob is set to 12:00. When turned counter-clockwise, lowpass filtering is applied and when turned clockwise, highpass filtering is applied. The filter also has a nice-sounding resonance parameter. This module provides hands-on control over the sound during the performance, as well as unconventional timbre modulations that are hard to achieve with conventional state variable filters. The Black DJ VCF is a fully analogue design and consists of two VCFs - highpass and lowpass in series and the filter management is done by complex CV routing.

CUTOFF
This is the main control of the module - manual cutoff frequency adjustment with a twist - it's fully open when the cutoff knob is set to 12:00. When turned counter-clockwise, lowpass filtering is applied and when turned clockwise, highpass filtering is initiated

AUDIO LVL
Adjust the audio signal level

RESONANCE
Adjust the resonance level manually. On settings over 1PM, the filter will start to self-oscillate. The resonance is incoming audio signal-sensitive - a signal of greater amplitude may reduce the impact of resonance on the resulting sound

CV1 LVL
This is the cuto CV attenuverter. Adjust the CV level to your taste! Notice that the cutoff CV works differently compared to conventional state variable filters - it sweeps the filter from closed lowpass through fully open to closed highpass

CV2 LVL
This is another cuto CV attenuator

CV2 IN
This is the cuto CV2 input, which is controlled by the attenuator knob

AUDIO IN
Patch your audio signal here.

OUTPUT
This is the audio output of the module.

CV1 IN
This is the cutoff CV1 input. The CV1 level is adjustable by the CV1 LEVEL attenuverter knob.

Features
Fully analogue DJ-style VCF
Manual resonance control
Cuto ff CV attenuverter and attenuator
Input and output
Protection against undesired overvoltage

Technical specifications:

Audio level: 10Vptp
CV level : -10V - +10V
Filter slope: 24dB/oct
Power consumption: +55mA, -58mA
Module width: 10HP
Module depth: 35mm

Notes: Black Stereo Mixer is just what you need, if your setup has several nowadays gaining popularity modules with stereo inputs or outputs, like Black Hole DSP, Erica Fusion Delay, MI Clouds or some other. In order to save rack space, we designed compact mixer with lot of cool, performance oriented features.

In order to save rack space, we designed a compact mixer with a lot of cool, performance oriented features.

Check out also the Black Pre-fade Listen Expander that is a satellite module to Erica Synths Black Stereo Mixer!

Erica Black series are high-end modules with unique functionality. Only the highest quality components are used and all inputs and outputs are protected against undesired overvoltage. When designing the Black Series, we did not economise on the module width, we put design and usability first. Big knobs are assigned to functions that make difference in sound. Together the Erica Black series are a range of modules that make an entire synthesizer.

Notes: Erica Synths Clap is developed together with French company e-licktronic and it's our take on analogue clap circuits adapted for modular systems. Sharp, punchy sound, Accent & CV control over Tone make it distinctively expressive in studio and live performances.

Features
Tone and Decay controls
CV control with an attenuator over Tone
Manual trigger
Accent for Better expression

Decay range: 120ms - 1100ms
Audio output level: -5...+5V
CV level (full span): -5 - +5V
Trigger level: 5V
Trigger time: 1ms
Accent CV level: 10V
Power consumption: 24mA@+12V, 20mA@-12V
Module width: 6HP
Module depth: 35mm

On this run of modules the Pitch & Decay CV inputs are inverted: rising CV will decrease pitch, falling - increase.

Notes: Pico Drum2 is compact yet versatile percussion synthesizer in a 3 HP eurorack module. It features 8 drum synthesis algorithms created to deliver distinct sounds to your modular system. Each algorithm offers a lot of flexibility therefore a big sounding bass drum and a squelchy snare can be dialled in within the same algorithm. It also tracks 1V/Oct and all parameters can be mapped to the CV1 input.

Technical specifications:
Output level: 10Vptp
CV level (full span): -5V - +5V
Power consumption: +28mA, -5mA
Module width: 3HP
Module depth: 35mm

Notes: Pico EF is Erica Synths' take on envelope follower module in 3hp! Pico EF features a preamp with +40dB gain (enough to boost even guitar and dynamic microphone signals for use in a modular system), envelope output with adjustable attack time and a gate output with adjustable threshold. The Pico EF can be used as a preamp, overdrive unit or for controlling VCFs with audio signal, or to use with external instruments to control your modular system in other creative and experimental applications.

Technical specifications:

Preamp boost: up to +40dB
Audio output level: 10Vptp
Envelope output level: 0 - +10V
Gate level: +5V
Power consumption: 25mA, -15mA
Module width: 3HP
Module depth: 35mm

Notes: Erica Synths Pico VCO 2 - powerful, full analogue VCO with great tracking over 8 octaves just in 3HP! Combine two of those, add some PWM and have a sound of real analogue beast!

Features:

Manual TUNE and PWM controls
+-1 octave switch
1V/oct input with good tracking across 8 octaves
PWM CV input
Pulse and triangle waveform outputs
Input protection against overvoltage
Protection against reverse PSU connection

Technical specification:

Output signal amplitude: -5V - +5
PWM CV input (full span): -5V - +5V
Power consumption: +21mA, -19mA
Module width: 3HP
Module depth: 35mm

Notes: This filter is based on the classic 2600 from the seventies and uses the LM3900 Norton opamp chip.

It has an audio inputs, two CV ins and an audio out.

You can control audio input level, CV levels, frequency cutoff and resonance.

It has a beautiful sound and it can go from relatively clean to dirty and screamy depending on audio signal level and resonance.

Tech specs:

- 8HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 7mA , -12V 13mA

Notes: The C-1U module is a one-channel module for recording and playing back movements of controller. Those can be recorded with channel's knob. The movements will be output as control voltage. The record time amounts to one minute maximal.

The track can be played once only (one shot) or in loop. The speed of the play back or the output offset is controllable with the pot. There are an additional CV input for CV recordings and a reset input.

The track data remains permanently stored when a 3V battery is used to buffer the RAM. When the module is switched on, the recorded data is available again. The module can be operated unipolar or bipolar (set by jumper on the back).

Note: The C-1U KnobRekorder uses a standard 3v lithium backup battery , type CR2032. The battery is needed to keep recordings and settings stored when the Eurorack case is turned off.

Dimensions: 12 HP
Power consumption: 20mA at +12 V and 9mA at -12 V

Module is a 1U tile.

Notes: The "uMM" combines a MIDI merger and two independent THRU distributors in a module that is only 4 HP wide. All sockets on the module are in MIDI TRS-B format.

At the heart of the two-input MIDI merger is a small, powerful ARM processor with plenty of buffer memory. Two MIDI streams are mixed to one output and can also be tapped via an additional second output. Two LEDs signal the operation of the merger: one LED indicates MIDI activity at the inputs, and a second LED warns of too much data at the inputs.

The second group of functions consists of two independent, separate MIDI THRU distributors. The MIDI data at the respective MIDI input can be picked up and distributed at the three THRU outputs. If required, a 1-to-5 distributor can be created from the two units by connecting an output of the left group to the input of the right group.

Features:

4x MIDI IN (TRS-B)
2x MIDI-OUT (TRS-B)
6x MIDI-THRU (TRS-B)
Powered via Doepfer connector

Notes: The 333 is a summing and distribution module for Eurorack modular systems.

It is composed of three identical sections, the red, yellow and green, each of those featuring three inputs summing amplifier with three independently buffered outputs.

Derived directly from the CGM creative mixer series, the sum section is DC coupled, allowing the sum of control voltages as well as audio signals.

With an extremely low tolerance in both sum and output sections, it is suitable also for summing quantized voltages like the ones coming out from the quantized outputs of the SAPEL.

In case CVs or audio signals are particularly hot, the 6dB attenuator might be helpful to reduce exactly by 50% the incoming signals.

Red and yellow output are also normalled to the 1st jack socket of the yellow and green input: in this way this module can also work as a 1 to 9 buffered multiple.

Notes: Shapes is a wide ranging and fully analogue oscillator which can perform duties as both auxilliary VCO* as well as VC-LFO. Shapes can be configured to cycle continuously, or to provide one-shot shaped outputs. When set to one-shot mode, Shapes may be used as an ersatz envelope generator.

Using the Time knob, Shapes can cycle from as low as 8 seconds (whale song) to as high as 19500Hz (bat beeps).

Shapes has 3 simultaneous outputs:

sawtooth (+/-5V, 10Vpp)
ramp (+/-5V, 10Vpp)
triangle (+/-5V, 10Vpp)
Additional waveforms may be derived courtesy of the Shape knob. Anticlockwise from 0 achieves progressively logarithmic sawtooths and ramps, whereas clockwise from 0 achieves progressively exponential sawtooths and ramps. The effect of the Shape knob on the triangle waveform is asymmetric, anticlockwise from 0 achieves progressively logarithmic leading edge, whereas clockwise from 0 achieves progressively exponential falling edge. Progressively exponential triangle waveforms can be achieved using the Time CV knob (set Shape knob to 0) providing there is no jack in the Time CV input socket

Time CV input provides wide ranging control of time. It is possible to dial in something approaching 1V/oct over a limited range, although Shapes has not been designed to perform as an accurately tracking VCO. In the audio range, Shapes comes into its own when used as a 'daughter' VCO to an external 'mother' VCO by patching the 'mother' VCO into Shapes' Gate In input socket - some impressive oscillator sync style effects can be achieved.

Gate In can also be used to initiate waveforms in one-shot mode, where a pulse of any length will cause Shapes to complete one cycle.

*Shapes has not been designed to perform as an accurately tracking audio VCO.

Product Specifications

12V draw: 15mA
5V draw: 0mA
-12V draw: 15mA
Depth: 45mm
Width: 4HP

Notes: 3xVCA offers three high class amplifier circuits with linear characteristic. Thanks to AC / DC compatibility, a very low noise floor and basically no distortion, the module is not only a great partner for control voltages, but audio material as well. Besides a signal input and output, each VCA has its own CV input. The dual potentiometers regulate levels and bipolar CV attenuation values of all amplifiers. Using these rather unusual, yet very practical components, it was possible to equip the 3x VCA with a front panel that is only 6 HP wide. Switches allow the user to feed the results of one amplifier to the output of the next amplifier, so we can get 1+2, 2+3, and 1+2+3 outputs mix. Two-colored LEDs visualize CV and output signals.

60 mA +12V
60 mA -12V
35 mm Depth

Notes: Mix up to four stereo channels in just 4hp, or chain multiple modules together to add channels. Inputs are normalled for mono operation. Simple, compact and high quality at a reasonable price.

Supplier's Notes:
4xSt.Mixer is 4 HP quad stereo mixer.

Right inputs are normalled to Left inputs for easy mono operation

Several 4xSt.Mixers can be chained together or with other HN stereo modules via sockets on the back side

65 mA +12V
50 mA -12V
35 mm deep

Notes: Dual xFade is a compact voltage controlled crossfader suitable for both audio and CVs. Smaller knobs set manual crossfade between A<>B, and bigger knobs are CV attenuverters. LEDs show the adjusted positive and negative CV sides for easy monitoring.

Upper inputs (section 1) are normalled to lower inputs (section 2). Thus the same signal pair A&B can be differently crossfaded in both sections.

The switch clones section's 1 controls to the section 2, which is useful to make stereo Dry/Wet adjustment or stereo VCA.

This module can be used as:

two independent crossfades

two independent VCAs

stereo crossfade or Dry/Wet control

stereo VCA

panner

Four jumpers on the back can give optional 5x amplification for each A or B input. Sot it is easy to crossfade modular level with linear level from pedals. Installed jumpers give 1x amplification, removing jumpers gives 5x amplification.

Output 1 is mixed with output 2 if left unconnected.

Notes: Clever FM module that does digital-style through-zero FM using analogue circuits. Use any signals from other modules as your carrier and modulator, then phase modulate or wavefold in the FM Aid.

Supplier's Notes:
FM AID is a module designed to perform through-zero linear Frequency Modulation (FM) in the analog modular world. Any arbitrary signals can be used as a Carrier and Modulator. The module copies FM in how it is done in digital implementation, but in a completely analog circuit free of digital aliasing artifacts. Digital or software FM oscillators are mainly based on a ramp waveform which is then shaped to other waveforms. This is also represented in the FM AID module: sawtooth signal is expected on the Carrier input to give the indicated sine, triangle, sawtooth and square waveforms on the respective outputs. However the user is not limited to only use sawtooth for the Carrier and any other signal can be plugged giving many complex waveforms at the outputs.

All known FM tricks from digital implementation are also applied - you can endlessly experiment with the Carrier/Modulator frequency ratios, Modulation index (FM knob), Modulator's amplitude shaping (CV knob), feedback FM (output is fed back to the Modulator's input) and many other.
Carrier input has normalled connection to the Modulator's input. This internal routing is disconnected each time a plug is inserted in the Modulator's input. That is a handy option which allows the module to be used with only one signal source - this single signal will act as Carrier and Modulator at the same time. There won't be any frequency differences between Carrier and Modulator in this case, but many interesting wave folding sounds will be available anyway.

Technically speaking FM AID uses Phase Modulation, not Frequency Modulation. The sonic difference is that the produces sound is brighter.

SPECIFICATIONS

Carrier input level: -5V ... + 5V (can also accept inputs ranging from -1V ... +1V] to [-12V ...+12V] / [-15V ...+15V] using onboard trimmer)

Modulator input level: preferably -5V ... + 5V

CV input level: preferably -5V ... + 5V

outputs level: -5V ... + 5V

outputs impedance: 1 kOhm

module depth: 3 cm or 1,5 inches

power consumption: +45 /-45 mA at +/-12 Vdc, +50 /-50 mA at +/-15 Vdc

Notes: HN VCF is a state variable filter having 12 db Low Pass, 12 dB High Pass, 6 dB Band Pass plus 18 db Low Pass marked as "LP!", because it has extra drive. All three parameters: "Freq", "Resonance" and "Drive" have dual knobs with outer knobs controlling bipolar CV amount. These affected CVs are then shown by the relative green/blue LEDs.

The possibility to have CV over "Resonance" and "Drives" makes it a very capable 6 HP filter.

"LP!" output has 6 dB steeper slope (18 dB) compared to ordinary 12 dB "LP" output. Plus it has much more drive.

Dimensions
6 HP
35 mm deep

Current Draw
55 mA +12V
65 mA -12V

Notes: You've been up all night in a bidding war on eBay to win a prized 80s rack effect unit - you can't wait to add some serious cheese to your tracks, and the sound of gated reverbs ring in your ears. Your heart pounds, and your pulse rises to crescendo as you win the auction! But there is one problem: your Eurorack system runs way too hot to simply plug straight into your stereo FX units. Your heart sinks, as you realize there is not much you can do that doesn't involve a lot of messing around with complicated and weird mono modules. That is, until now: introducing the Herzlich SFXI.

The Stereo FX Integrator was designed in response to my own need: owning several cool stereo FX units, and having no easy way to integrate them with an easy send and return, in my Eurorack system. Attenuate your Eurorack signals down to line level, or even all the way down to instrument level, and get a nice, clean boost back up to modular levels, with this dead simple and highly useful device from the R&D department at Herzlich Labs.

You can even use it to integrate external stereo line level signals into your Eurorack, which is both nice and convenient, and also useful. Finally, you have an easy way to get the sound of your JV1080 into your Clouds.

The scientists have been working overtime to produce this unit, and were fed extra rations of maize and millet gruel just to bring you this circuit. Every SFXI sold will grant the poor souls at Herzlich Labs another serving of maize and millet gruel. Please think of the poor scientists at Herzlich Labs.

Dimensions
4 HP

Current Draw
30 mA +12V
30 mA -12V
0 mA 5V

Notes: The Hungry Robot Sample & Hold provides basic S&H functionality with some added bells and whistles. It uses an internal clock dialed into a very useful range. If the internal clock rate is not to your liking, you can bypass the Rate knob by patching a clock signal into Clk In. The Sample & Hold has a built in attenuverter giving a bit of added control over the random voltages that are outputted. White noise out for uses elsewhere. Traditionally a S&H samples voltages from chaotic white noise, but E.In allows you to bypass the white noise and patch in your own sample source (i.e. patching an LFO in for a bit crushed LFO). As with all Hungry Robot "Modular Boxes" the Sample & Hold can be powered with a simple 9V DC, Negative Center power supply.

KNOBS
-MINUS/PLUS: Attenuverter for output. Allows you to sweep between positive and negative voltage outputs.
-RATE: On board clock source ranging from approximately 25ms to 1000ms.

PATCH POINTS
-E.IN: Bypasses internal white noise as a sample source. Patch in any CV source that you want to sample from
-STATIC: Taps into white noise output (0-5V range)
-CLK IN: Bypasses internal clock with your provided external clock
-S&H OUT: Two buffered outputs of S&H voltage

Dimensions: 4.7" x 2.6" x 1.5"
Power: 9V DC - Negative Center - 2.1mm Barrel

Notes: Lovely little mono filter module in a compact desktop format. Based on the classic Prophet 5 filter, ideal for processing synths and signals, hooking up to Eurorack or other Hungry Robot modules.

Supplier's Notes:

The Hungry Robot VCF is an all analog, 4-pole low pass filter with a self-oscillating resonance control. It is a close replication of the filter circuit found on the famous Prophet 5. It uses a HM2040 which is a high quality, faithful replication of the original SSM2040 chip. This resonant filter has a beautiful tonal quality. The over-sized knobs provide a satisfying tactile response. The cutoff frequency can be controlled by external control voltage. It has a built-in attenuator and invert switch for the incoming CV. CV input does not track at 1V/Oct, but is scaled to act as a VCA when a 5V signal is applied to CV input. As with all Hungry Robot "Modular Boxes" the VCF can be powered by a simple 9V DC, Negative Center power supply.

KNOBS
-FREQUENCY: Sweeps the cutoff frequency of the filter.
-CV: Attenuator for incoming CV input.
-RESONANCE: Sets resonance of filter. Small volume drop is to be expected. Will self-oscillate at higher settings.

SWITCHES
-INVERT: Inverts the incoming CV input. Toggle to the right to invert incoming CV

PATCH POINTS
-IN: Patch Audio Signal In
-CV: CV input for Frequency. Allows for CV control of this parameter.
-OUT: Patch Audio Signal Out

Dimensions: 4.7" x 2.6" x 1.5"
Power: 9V DC - Negative Center - 2.1mm Barrel

Notes: Get Amped

Amps comprises two precision linear VCAs that have been carefully designed to offer a wealth of flexibility and additional functionality. The front panel controls and signal normals allow these two VCAs to also be configured to function as: line level boosters, crossfaders, ring modulators, mixers, and much more. They can also be chained together by way of an included cable to form larger, more complex systems.

Amps features cascaded CV inputs and cascaded mix outputs allowing it to be used in a number of versatile configurations. A boost switch enables you to amplify each VCA's input by either +6dB or +20dB i ideal for boosting low amplitude signals or pleasingly overdriving audio. The addition of a phase inversion switch for the second channel allows Amps to function as a ring modulator. The CV normalization, which can also be inverted and offset, also allows for VC-Crossfader functionality.

Features

Manual LEVEL slider per VCA i convenient when using the module as a mixer, or for biasing the signal for CV (such as when modulating the VCA with a bipolar LFO).
Dedicated CV attenuators with dual color LEDs for monitoring bipolar CV signals.
Linear response curve.
Input and CV normalling of VCA A to VCA B to allow a single source to feed and/or control both VCAs.
Output normalling of VCA A to VCA B to allow both VCAs to feed a single output.
Each VCA has a boost switch that can increase the output level by either +6dB or +20dB.
Phase Invert switch on VCA B allows for ring modulation capabilities.
CV Invert switch on both VCAs allows for crossfading one signal into another.
4-pin link connectors on the rear panel allow for multiple AMPS modules to be chained together to create a 4-channel mixer; 6-channel mixer; etc.

Dimensions
6 HP
36 mm deep

Current Draw
40 mA +12V
46 mA -12V

Notes: Noise Random Tools comprises a collection of useful utility blocks that you could use in many of your patches - Clock, Random Pulse, Analog Noise, Sample and Hold, and Slew.

Features:

- Clock and Random pulse source with adjustable rate
- Analog pink and white noise source with very accurate spectrum
- Analog sample / track and hold with very low droop
- Analog slew with adjustable slew rate

Notes: Outs enables your modular system to output both professional and prosumer compliant audio, and send it to external amplifiers, mixers, recording devices, or DAW interfaces. Using the L+R Level knob, it scales modular-level voltages down to the level required to drive external gear at either the +4dBu balanced professional line-level standard or the -10 dbV unbalanced standard.

Headphone monitoring is also provided via a low noise built-in headphone amp (with its own independent level control), capable of driving a wide range of impedances - from studio grade headphones to portable style earbuds.

To use Outs, simply connect the final output of your patch to the 1/8" inputs (where the built-in activity LEDs light up to indicate the presence and intensity of the input signal). The left input is normalled to the right, so you can create a stereo signal from a mono source. Or if you have an Intellijel Mixup, you can remove a jumper from its rear panel, and connect it to the Outs module using the 3-pin link cable included with the Mixup.

Notes: SVF 1U

Multimode State Variable Filter

The perfect 1U, multimode, voltage-controlled filter for sweet-sounding subtractive synthesis duties or to form the basis of more complex patches. Punchy, clean, and precise. Explore new sounds through the dual modulation inputs and dedicated low pass, high pass and band pass/notch outputs. This filter responds beautifully to audio rate FM and you can self-patch to get even more interesting filter responses. Adjust the Q for a sharp howl or use it as a sine VCO.

Features:

Dedicated 2-pole Low pass filter (LP) and 2-pole High pass filter (HP) outputs.
Switchable Bandpass filter (BP) and Notch filter (N) output.
Optional +6dB input boost and asymmetric clipping circuit.
PITCH input tracks 1V/Oct accurately over 4+ octaves.
FM CV input with attenuverter.
Capable of generating very low distortion sine waves from 2Hz to 20kHz when driven to self oscillation (Max Q).

Size: 20HP
Depth: 35mm
Power: 27mA @ +12V 30mA @ -12V

Notes: Triplatt is a three-channel active/buffered attenuverter and summing mixer. Each channel has a knob, which can function as a unipolar attenuator or a bipolar attenuverter, depending on the setting of its corresponding two-position polarity switch.

Each input is normalled to a built-in precision +5V DC voltage source. With nothing plugged into the jacks, each knob controls a voltage range of 0 to +5 V or -5 to +5 V depending on the position of the channel polarity switch. Outputs A and B are also capable of a range of 0-10 / -10 to +10 when using the special function switches.

Each output is normalled to mix into the output of the channel below, making it possible to do sub mixes in groups of two or three.

In addition, each channel has a "special function" switch to alter its input voltage in a specific way. Channel A has a 2x voltage multiplier switch, allowing you to double the voltage sent into Channel A. Channel B has a +5V switch, allowing you to add 5V to whatever voltage is sent into Channel B. Channel C has a mute switch, allowing you to completely turn off the signal being sent into Channel C.

Notes: This is the version II of the original uVCA.

This module was adapted from a design by David G. Dixon

Notes: Mighty oscillations, mini size.

An analog oscillator and LFO with pure waveforms and precise tracking in a compact package. Perfect as a utility modulation source but equally capable to be used as a primary sound source. Patch it up and let it rip!

Features
Four simultaneous pure waveforms: Sine, Triangle, Square and Sawtooth
Pitch input for 1V/Oct tracking and FM
SYNC input for Hard Sync. This input has a comparator so that you can use a variety of waveforms as triggers.
Switch to select VCO (audio) or LFO range of operation
Three position Octave switch to jump pitch up or down by two octaves
PITCH knob has three octave range in VCO mode (extended to seven with the octave switch) and seven octave range in LFO mode (extended to 11 with the octave switch).
Bicolor led indicates the state of the triangle core rate

Specs
Width 14HP
Depth 37.5mm
Power 19mA @ +12V
16mA @ -12V

Notes: Sometimes your ears are not enough and you really need to see the sounds and control voltages you are generating. Zeroscope's two channel design lets you display and compare both control voltages and audio. It's a good old fashioned sci-fi light show!

The Zeroscope 1U is an adaptation of the excellent 3U Zeroscope by VPME.DE.

Three Modes Packed Into 1U:

- Scope: Standard graphical display, with time displayed on the X-axis and voltage displayed on the Y-axis.
- X-Y: Alternate graphical display with CH 1 driving the X-axis and CH 2 driving the Y-axis.
- Tune: Alphanumerical tuning display, which you can configure to show either Hz values or note names.

The Scope displays have adjustable display offset for each channel and an adjustable trigger threshold, while the tuner has options for reference pitch and average update speed.
Ins & Outs

The inputs are DC coupled and accept signals between -10V and +10V. The Signal on the input is normalled to the output below; this allows you to monitor or tune a signal without a mult or re-patching.

Notes: All channels support headphones with 16 - 600 Ohm impendances.

Superb sound with low distortion and great low end.

Linkable channels (B to A and C to A).

All inputs with multiples, ie feeding different mixer channels.

Mono input is normalized to stereo.

Protected with relais, assuring soft starts and DC protection for your headphones (> +/- 10V input)

Width: 12 HP

Notes: GOBLET is an analogue filter and distortion unit with some added quirks and extra controls.

Why:

To make stuff sound filthy.
To shape the output of an oscillator.
To live interact with the sound during a performance.
To soft sweep the cutoff thanks to the optocouplers logarithmic response.

With:

Simple waves - make them unrecognizable.
Complex waves - shape them into something new.
Percussions - crank the resonance and give an acid twist to a beat.
No input - play with the feedback and the touch controls.

Dimensions:

8 HP
18 mm deep

Current Draw:

45 mA +12V
25 mA -12V

Whichever power connector you use should work fine with the polarity.

Notes: By combining a mixer and four VCAs in a single module, Mix 3 manages to provide a unique combination of compact size and functionality in just 6 HP. High-end signal paths ensure extremely low noise and distortion, wide headroom and precise gain control, despite the small form factor.

Each of the three main channels has an exponential response, which is more natural for audio than linear, as it matches the human hearing. However, all signal paths are DC-coupled, so control voltage (CV) signals can be processed as well.

What truly sets Mix 3 apart from other compact mixing modules are the three CV inputs, providing voltage control over the signal levels. This even allows you to go beyond unity gain and reach up to +20 dB of amplification. Once a CV input is used, the corresponding channel knob becomes a CV attenuator.

When clipping, Mix 3 does so in a clean, symmetrical way. This yields a very pure overdriven sound, only containing odd harmonics, and allows the module to be used as a triple voltage controlled distortion.

Additional features include audio indicator LEDs, a fourth auxiliary input, voltage control over the output level and a line output jumper setting.

Notes: Make quick changes to signal routing manually or with CV control. Any audio or CV signal can be routed via two outputs in series, parallel or reverse series. Quick, clever and easy to use.

Supplier's Notes:
Signal flow is an essential concept in modular synthesis: the path taken by audio or control voltages (CVs) may be long or short, branching or linear, intuitive or highly complex.

While the patch programmability of a modular system is its greatest strength, it can also be a weakness: quick experimentation is often hampered by the need to repatch the synthesiser to change the signal flow.

Pivot 2 offers a unique solution: a compact, fully voltage controlled variable signal router. At the turn of a single knob, any signal can be routed through two external modules in series, parallel or reverse series, as well as any combination in between.

Experiment with patching wavefolders before, after or alongside filters, shuffle multiple delay lines, precisely dial in two-stage audio compression or easily control intricate feedback patches.

Looking beyond the basic signal routing application, Pivot 2 will also function as a complementary pair of counter-acting linear voltage controlled amplifiers (VCAs), a voltage controlled crossfader or a voltage controlled panner.

Analogue voltage controlled send/return router.
Seamless transitions from series, through parallel on to reverse series effect routing.
Also functions as a complementary VCA pair, voltage controlled crossfader or panner.
Impedance-compensated outputs with dual-colour LEDs.
Premium mounting hardware: black screws, black nylon washers and matching hex key.
High-quality components and assembly; designed and made in Belgium.

4 HP | +12: 60 mA, -12: 60 mA

Notes: Designed with and for performing artists, Switch 4 delivers a hands-on signal switching and routing solution for your Eurorack modular synthesiser.

Quickly mute audio signals, trigger envelopes live, select modulation sources on the fly... With custom dual-action toggle switches, an intuitive interface and sturdy construction, Switch 4 will prove just as useful on stage as in the studio.

The bottom switching section includes four lever-actuated toggle switches, to make or break the signal path between the inputs and outputs. These switches feature a dual action: latched upwards, momentary downwards.

The four input signals are also sent to the top routing section, where two rotary switches allow you to select the signals to be sent to the matching outputs. Here you'll also find dual-action toggle switches, for added versatility.

Finally, all signal paths are buffered, avoiding signal cuts when shorting a jack during patching or severe loading effects when driving many inputs. The high-end components provide exceptionally low noise and distortion, so Switch 4 can reliably process audio, control voltages and gates/triggers.

Notes: Clever four-channel utility module designed to make it easier to achieve perfect oscillator tracking and transpose CV signals. Also includes some neat quantising and portamento features.

Supplier notes:
The CalTrans solves issues encountered when playing tonal music with a modular system: tracking problems, curves unrelated to Volt per octave ratio, limited octave range, cumbersome transpose, ...

The CalTrans corrects and expands the range of troublesome VCOs and brings V/Oct tracking to anything that oscillates.

Besides calibration, the CalTrans offers live play features. Each channel can be quantized and any combination of them transposed jointly.

A pair of rotary encoders with detent allow an precise selection of octaves and semitones.

VCOs whose tracking doesn't go high enough to follow the leader will see their pitch repositioned in their highest possible octave so that the global harmony is unaffected.

You can add a pinch of portamento and glissando to each channel and save the whole in user presets.

Notes: Focused versatility seems an oxymoron when describing the features that led us to design the Mixwitch.

With only a pinch of mixing, inverting and controlled switching, we brew up a plethora of combinations and uses.

This is voltage processing magic!
The Mixwitch design comes from a frustration with attenuvertors (bipolar attenuators-inverters) whose off (neutral) position is difficult to retrieve, especially in live situations.

We went for a digitally-controlled analog path where polarity inversion would be at the touch of a button. So, the usefulness of attenuating/inverting can be realized by turning the pot down, swiftly pressing the inversion button and reopening the level. The zero level is where you expect it, with the pot full down.

Once we had a clean polarity control, we easily added a mute function offering the benefit of pre- adjusted pot settings ready to be activated at will.

The next step was to bring something extra, useful and creative. There are plenty of analog switches controlled by a clock; but arbitrarily selecting an input with a voltage is less known. Having both control capabilities combined with our specific mixer features creates a unique fusion: welcome to the Mixwitch !

Notes: Affordable logic processing in this appealing little module from Klavis. Two independent dual-input processors offer a total of 15 different functions, with different options on each section.

Supplier's Notes:
Two dual-input sections can be used independently, put in parallel for 4-input wide logic, or chained for more advanced processing.

Each section presents normal and inverted outputs.

The two sections offer a set of common and specific functions for a total 15 different ones.

Several functions offer real-time CV control for dynamic changes of the conditions.

All time-related functions can be independently user adjusted and are saved automatically.

LEDs tell permanently the actual status of all outputs.

Dimensions:
5 HP
21 mm deep

Current Draw:
31 mA +12V
1 mA -12V
0 mA 5V

Notes: Strom+ is a strong, reliable and safe 4HP power solution for your modular system. The Strom+ power module includes many safety mechanisms to prevent your modules from being damaged. These include most importantly short-circuit protection, overvoltage protection and a replaceable main input fuse. See the full list below.

Strom+ also offers a current sensing technology that indicates current consumption of your system. LEDs of each rail will turn orange then red, when current consumption reaches or crosses the maximum load of that rail.

Strom+ has extremely low ripple, even under full load. This means better sound and stability for your modules.

One module can power multiple skiffs via Strom Passive Module, a Strom Connector Cable, or a KOMA Strom Busboard.

Technical Specifications

Inputs and Outputs

Output: 1.5A @ +12V | 1.5A @ +5V | 1.0 A @ -12V
Input: 15V, 4.6 A (center positive)

Safety Mechanisms

Replaceable input fuse. Protects the wall-plugged adapter. The KOMA Strom AC/DC adapter actually has its own protection mechanisms and will itself shutdown in most cases before the input fuse trips.
Input overvoltage. Strom+ works up to specification from 15V - 20V input and works out of specification up to 28V input.
Input reverse polarity protection
Output overvoltage protection
Output short-circuit protection
Output over current protection
Output undervoltage protection
All above output protections independent for each rail. If any rail fails, the whole module shuts down.
Connectors and Controls

Main DC-Input (15 VDC)

On/Off switch
Front panel connector to a passive Strom module
2 standard Eurorack 16-pin connectors (for modules or a flying busboard)
Back panel Strom connector to solid busboards

Dimensions

4HP
48mm without Eurorack power connector connected (distribute power via Strom connector cable)
52mm with Eurorack power cable connected

Notes: An ultra-compact 10HP VC filter with bags of personality. Camber can be treated as a subtle, non-intrusive sound design tool, or something much more lively.

Camber is designed to be a fun, tactile filter with a small footprint. It's sound is neutral enough for basic filtering without a fuss, with a much more aggressive tone available using high resonance settings in three-pole mode.

Filter Core

The core of the filter is based on a state variable topology using 2164 VCAs and 1% tolerance integrating capacitors. Resonance and feedback control is provided by the fantastic circuit design originally by Neil Johnson "Voltage Controlled 3-Pole State Variable Filter" recently made available in Sound Semiconductor documentation.

Operation

Camber is switchable between low pass and high pass responses with one pole (6dB) and three pole (18dB) flavours of each. It has full CV control of both cutoff frequency and resonance amount. The input is DC-coupled allowing LFO and CV signals to be routed through the filter. The filter will also act as a simple oscillator producing a clean sinusoidal signal with the resonance control turned *almost fully clockwise, and no signal at the audio input. Dialling in the resonance so that it is just under the point of self-oscillation allows the filter to be "Pinged" by sending gate signals to the audio input. This is useful for tuned percussion sounds and FX.

Specifications

Intellijel 1u format
Width 10HP
Depth 33mm
Power requirements ~40mA +12V/~40mA -12V
Control voltage range 0-8V
Impedance Input 100K / Output 1K

Notes: Volume 1 pot: regulates the volume for the mini jack input 1.

Volume 2 pot: regulates the volume for the mini jack input 2.

Volume 3 pot: regulates the volume for the mini jack input 3.

Send out the mixer signal before the resonant equalizer, mini jack out, to use with external effect or as mixer dry out.

Return pot: regulate the volume for the mini jack return input, to use with external effect or as a 5- input.

Resomix has one mono mini jack out.

High pass, band pass, low pass switch; selects the filter type.

High, mid, low switch; selects the filter frequency range.

Cutoff pot: regulates the cutoff frequency of the filter, the 0-10v CV input affects the cutoff frequency to obtain the CV in maximum effect keep the cutoff pot to 0.

Resonance pot: regulates the resonance level.

Gain pot: regulates the gain level at the filter input, work as general mixer gain.

Resomix works with a +/-12v 10pin modular connector.

Dimensions

8 HP
38 mm deep

Notes: Sindikat is made to be placed in the heart of every modular setup: copy, invert, attenuate, scale, get different polarity versions simultaneously of two pair of mixes, mix CV as well as audio (up to 8 sources in total), mute or switch to add desired source to a bigger unity mix, scale two separate mixes with chosen gain.. All circuits can preserve their independent use and/or be combined!

Details & use:

The module consists of circuits designed to group the most useful operations for signal mingling in modular synth setups -but in the more fun manner!

It is designed in the way that the circuits can function independently -be patched to the other modules- or to be combined inside the module at the same time!

On the top of the module there is a buffered multiple (the bi-color led is indicating signal input and its polarity) : Next to the input there are two outputs giving the exact copy of the incoming signal. On the third output you'll get the 'attenuverted" version of that signal which is controllable by the dedicated attenuator/inverter potentiometer.

This signal can be further added (or muted) via its switch, internally to a unity gain mixer situated on the bottom of the module via its SUMM OUT.

This mixer has its own 3 inputs who will accept CVs as well as audio signals with an output gain of 1/3.

Its bi-color led will indicate the polarity of the incoming signals.

In the center of the module there is a CV Processor consisting of two mixers each mixing two signals- in the way that:
The first one takes two signals (A and B) and outputs simultaneously the positive version of their mix (AB+ OUT) and the negative version (AB- OUT).
Their gain is scaled by the potentiometer: going on 1x in the middle position to 2x fully turned. (After middle position with a stronger signal and due to higher gain it will start to saturate producing an distortion-like effect)
Further, via their switch, those mixes also can be added to a unity gain mix (SUMM OUT) and therefore creating a larger mix.
You'll do that by choosing which polarity output you want to send to a summing mix.
In the middle position of the switch the signal is "off" so you can use this to mute/un-mute the signal in the unity mix. Also, even if it is in "off" position this only breaks the internal link to a unity mix but you can still use their distinctive outputs to send your positive and negative mixes elsewhere in your system.

Goes the same for the second one: C and D inputs giving positive (CD+) output result and negative (CD-) simultaneously , all with gain select and the switch choice for summ positive or negative (or none) to a bigger unity mix.

You can also choose to use those two circuits as a simple attenuators for ex. by patching only one signal so you'll get an attenuator and polarizer at once!

The module can process CV and audio as well in every circuit.

Therefore, by summing eventually all the signals to a final "SUMM OUT" output you can create up to 8 sources -in the module- large mix!

Made for more fun with a modular!

This module fits perfectly well with Modulaire Maritime "Decca" switch-based manual control module.

As these modules are developed from practicing recording in "one take" (same for a live performing), combining them you get an extended control over CVs, gates and audio going on in the system, allowing to switch- stop/mute, change polarity, introduce/mix more gates, drums,.. on the fly.

8hp
25mm deep
Reverse voltage protected